RM TTS Communication Headset EY06489 User manual

Brand: RM

Model: TTS Communication Headset EY06489

Type: User manual

Warranty & Support

This product is provided with a one year warranty for problems found during

normal usage. Mistreating the Communication Headset or opening the unit will

invalidate this warranty. Any data stored on the unit and any consequential loss

is not covered by this warranty. The battery is not user replaceable.

Technical Support

Please visit www.tts-group.co.uk for the latest product information.

Email [email protected] for technical support.

TTS Group Ltd.

Park Lane Business Park

Kirkby-in-Ashfield

Nottinghamshire,

NG17 9GU, UK.

Freephone: 0800 318686 Freefax: 0800 137525

TTS Product Code:

EY06489

WARNING: Do not dispose of this product in household

waste. Hand it over to a collection point for recycling

electronic appliances.

WARNING! Not suitable for children under 36 months

due to small parts – choking hazard. Made in China,

on behalf of the TTS Group Ltd.

Communication

Headset

USER GUIDE

Nxxxxx

N448

TTS is proud to be part of plc

COMMUNICATION HEADSET MANUAL 3/12/14.indd 1 18/12/2014 16:17

Great for Communication outdoors

Communication

Headset

USER GUIDE

TTS is proud to be part of plc

COMMUNICATION HEADSET MANUAL 3/12/14.indd 2 18/12/2014 16:17

Important information

Please retain these instructions for future reference, as they contain important

information.

Use only the provided power adaptor.

The supply terminals are not to be short-circuited.

Do not allow the Communication Headsets to come into contact with water or

other liquids.

Keep the Communication Headsets away from direct sunlight and heat.

In the event of electrostatic discharge your Communication Headsets may

malfunction – please refer to the trouble shooting section for guidance on resetting

the units.

It is recommended that Communication Headsets are switched off when not in

use.

Know your Communication Headsets

On/Off Switch

Press to talk

Reset Button

Pairing Button

COMMUNICATION HEADSET MANUAL 3/12/14.indd 3 18/12/2014 16:17

Communication Headset

Using your Communication Headsets

Volume Adjustment

The Communication Headsets have a volume control on the headset. The

volume control is located on the right hand side ear cup, towards the back of the

headset. The control is raised slightly so it can be easily located without the need

to remove the headset during use.

Switching On and Off

To switch on, slide switch into the ON position. The status LED will light green

to indicate that they are ready to transmit and receive. Repeat these steps with

the other headsets. To switch off, slide the switch to OFF. The LED will turn off to

indicate headsets have fully switched off.

To Communicate

A green LED will indicate that the Headsets are ready to use. To talk, push the

button (microphone icon) on the right cup of the headsets. A solid Amber LED

will indicate headsets are communicating. The user wearing the other headset

should hear the sound from the first headset. As with all walkie-talkies the

Communication Headsets are half-duplex. This means both users cannot speak

at the same time and will need to alternate pressing the microphone button.

If the LED indicates an alternating red and green flashing light this means that the

destination headset is switched off.

Charging

When fully charged the Communication Headset will have a battery life of

approximately 10 hours continuous use (depending on distance and volume

setting). When the Communication Headset requires recharging, the status LED

will flash red to indicate low battery. To charge the Communication Headsets,

connect all the Headsets to the charger using the leads and splitter provided. The

statues LED will change to red to show they are charging. Once fully charged the

status LED will change to green.

COMMUNICATION HEADSET MANUAL 3/12/14.indd 4 18/12/2014 16:17

LED Indication

Green - Power on

Red (flashing) - Low battery. Headsets needs charging

Red (solid) - Battery charging

Green (solid) - Battery charged

Amber (solid) - Communicating

Amber (flashing) - Pairing

Green and red (flashing) - Receiving headset switched off.

Replacing the Ear cushions

The headset cushions can be removed and replaced with new ones (Available

from TTS product code EL00413)

The headset cushions can be removed and replaced with new ones (Available

from TTS product code EL00413)

To remove: Grip the ear pad firmly and rotate anticlockwise 1/8th turn. The whole

ear pad assembly can then be removed. To replace: Locate the lugs on the ear

pad assembly into the headset, and then rotate clockwise 1/8th turn until it clicks.

International Charging Adaptor

The Communication Headsets are supplied with a multi-region adaptor. The

adaptor is supplied with the UK plug fitted but this can easily be switched to suit

any country. Press the release button behind the plug head and rotate the plug

anti-clockwise to remove it.Replace with the desired plug head and rotate clock-

wise until it clicks into place securely.

The safety isolating transformer to be used with the product should be regularly

examined for potential hazards such as damage to the cable, cord, plug,

enclosure or other parts. In the event of any damage, the adaptor must not be

used until the damage has been properly repaired.

COMMUNICATION HEADSET MANUAL 3/12/14.indd 5 18/12/2014 16:17

Troubleshooting

In the first instance always check the units are fully charged, switched on and the

volume not set to zero.

If for any reason the Headsets malfunction, switch the units off, wait for 10

seconds and switch them back on again. If this doesn’t resolve the issue the

Headsets may have become unpaired. To re-pair the units complete BOTH (1) and

(2) below:

Reset the Headsets

Press the reset button. Green LED will flash once, indicating that it’s reset

Pairing

Press the pairing button of Headset A, amber LED will flash. Then press pairing

button of headset B, its amber LED will flash, Headset (A /or B) will search for

Headset (B/or A), LED will change to green when pairing is completed.

Communication Headset

Speciﬁcations

100 – 16KHz

16K – 20KHz

-30dB (± 3dB)

650mAH Lithium Polymer

10 hours (Typical)

Speaker frequency response

Microphone frequency response

Microphone sensitivity

Battery

Battery Life

Technical Specification

COMMUNICATION HEADSET MANUAL 3/12/14.indd 6 18/12/2014 16:17

RM TTS Communication Headset EY06489 User manual

RM TTS Communication Headset EY06489 User manual

RM TTS Communication Headset EY06489 User manual

Other documents