Gigabyte S451-3R0 User manual

Brand: Gigabyte

Model: S451-3R0

Type: User manual

R451-3R0

4U 38-Bay Dual Processors Storage Server

User Manual

Rev. 1.0

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentation:

 User Manual: detailed information & steps about the installation, conguration and use of this

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

software component (e.g. BMC rmware, rail-kit) compatible with this product.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents.

For More Information

For related product specications, the latest rmware and software, and other information please visit our website at

http://www.gigabyte.com

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller

portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

https://esupport.gigabyte.com/ to create a new support ticket

For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:

server[email protected]

Conventions

The following conventions are used in this user's guide:

NOTE!

Gives bits and pieces of additional

information related to the current topic.

CAUTION!

Gives precautionary measures to

avoid possible hardware or software problems.

WARNING!

Alerts you to any damage that might

result from doing or not doing specic actions.

Server Warnings and Cautions

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING!

To reduce the risk of electric shock or damage to the equipment:

• Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

• Unplug the power cord from the power supply to disconnect power to the equipment.

• Do not route the power cord where it can be walked on or pinched by items placed against it.

Pay particular attention to the plug, electrical outlet, and the point where the cord extends from

the server.

WARNING!

To reduce the risk of personal injury from hot surfaces, allow the drives

and the internal system components to cool before touching them.

WARNING!

This server is equipped with high speed fans. Keep away from hazardous

moving fan blades during servicing.

CAUTION!

• Do not operate the server for long periods with the access panel open or removed. Operat-

ing the server in this manner results in improper airow and improper cooling that can lead to

thermal damage.

• Danger of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)

CAUTION!

ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU

PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,

PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-

TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER

WHEN HANDLING PARTS.

Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by

their edges without any component and pin touching. After removing a board from its protective

wrapper or from the system, place the board component side up on a grounded, static free sur-

face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over

any surface.

System power on/off: To remove power from system, you must remove the system from

rack. Make sure the system is removed from the rack before opening the chassis, adding, or

removing any non hot-plug components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be

present on power, telephone, and communication cables. Turn off the system and discon-nect

the cables attached to the system before servicing it. Otherwise, personal injury or equipment

damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,

boards, and other parts. We recommend that you perform all procedures in this chapter only at

an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic

wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling

parts.

ESD and handling boards: Always handle boards carefully. They can be extremely

sensi-tive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a

board from its protective wrapper or from the system, place the board component side up on a

grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.

Do not slide board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased conductor that

slips over two jumper pins. Some jumpers have a small tab on top that can be gripped with n-

gertips or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care

when using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper

with the pliers, never the wide sides. Gripping the wide sides can damage the contacts inside

the jumper, causing intermittent problems with the function con-trolled by that jumper. Take care

to grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the

board may bend or break.

CAUTION!

Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery

only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-

teries according to the manufacturer’s instructions.

- 7 -

Table of Contents

Chapter 1 Hardware Installation ...................................................................................11

1-1 Installation Precautions .................................................................................. 11

1-2 Product Specications .................................................................................... 12

1-3 System Block Diagram ................................................................................... 16

Chapter 2 System Appearance ..................................................................................... 17

2-1 Front View ...................................................................................................... 17

2-2 Rear View ....................................................................................................... 18

2-3 Front Panel LED and Buttons ........................................................................ 19

2-4 Rear System LAN LEDs ................................................................................. 21

2-5 Hard Disk Drive LEDs .................................................................................... 22

2-6 Power Supply Unit LED .................................................................................. 25

Chapter 3 System Hardware Installation ......................................................................27

3-1 Removing and Installing the Chassis Cover .................................................. 28

3-2 Removing and Installing the Fan Duct ........................................................... 29

3-3 Removing and Installing the CPU and Heat Sink ........................................... 30

3-4 Removing and Installing Memory ................................................................... 32

3-4-1 Six-Channel Memory Conguration ........................................................................32

3-4-2 Removing and Installing a Memory Module ...........................................................33

3-4-3 DIMM Population Table ..........................................................................................33

3-5 Removing and Installing the PCI Expansion Card ......................................... 34

3-6 Removing and Installing the Hard Disk Drive ................................................. 35

3-7 Replacing the Fan Assembly .......................................................................... 37

3-8 Removing and Installing the Power Supply .................................................... 39

3-9 Cable Routing ................................................................................................ 40

Chapter 4 Motherboard Components ...........................................................................43

4-1 Motherboard Components ............................................................................. 43

4-2 Jumper Settings ............................................................................................. 45

Chapter 5 BIOS Setup ..................................................................................................47

5-1 The Main Menu .............................................................................................. 49

5-2 Advanced Menu ............................................................................................. 52

5-2-1 Trusted Computing .................................................................................................53

5-2-2 Serial Port Console Redirection .............................................................................54

5-2-3 SIO Conguration ...................................................................................................57

- 8 -

5-2-4 PCI Subsystem Settings .........................................................................................58

5-2-5 USB Conguration ..................................................................................................60

5-2-6 Post Report Conguration ......................................................................................61

5-2-7 NVMe Conguration ...............................................................................................62

5-2-8 Chipset Conguration .............................................................................................63

5-2-9 Network Stack Conguration ..................................................................................64

5-2-10 iSCSI Conguration ................................................................................................65

5-2-11 Intel(R) I210 Gigabit Network Connection ..............................................................66

5-2-12 VLAN Conguration ................................................................................................68

5-2-13 QLogic FastLinQ .....................................................................................................70

5-2-14 Driver Health ...........................................................................................................72

5-3 Chipset Setup Menu ....................................................................................... 73

5-3-1 Processor Conguration .........................................................................................74

5-3-2 Common RefCode Conguration ...........................................................................77

5-3-3 UPI Conguration ...................................................................................................78

5-3-4 Memory Conguration ............................................................................................79

5-3-5 IIO Conguration ....................................................................................................81

5-3-6 Advanced Power Management Conguration ........................................................83

5-3-7 PCH Conguration .................................................................................................86

5-3-8 Miscellaneous Conguration ..................................................................................88

5-3-9 Server ME Conguration ........................................................................................89

5-3-10 Runtime Error Logging ...........................................................................................90

5-3-11 Power Policy ...........................................................................................................92

5-4 Server Management Menu ............................................................................. 94

5-4-1 System Event Log ..................................................................................................96

5-4-2 View FRU Information ............................................................................................97

5-4-3 BMC VLAN Conguration .......................................................................................98

5-4-4 BMC Network Conguration ...................................................................................99

5-4-5 IPv6 BMC Network Conguration .........................................................................100

5-5 Security Menu .............................................................................................. 101

5-5-1 Secure Boot .........................................................................................................102

5-6 Boot Menu .................................................................................................... 104

5-6-1 UEFI NETWORK Drive BBS Priorities ................................................................106

5-6-2 UEFI Application Boot Priorities ................................................................. 107

5-7 Save & Exit Menu ......................................................................................... 108

5-8 BIOS POST Codes ...................................................................................... 110

5-8-1 AMI Standard - PEI ...............................................................................................110

5-8-2 AMI Standard - DXE .............................................................................................110

5-8-3 AMI Standard - ERROR .......................................................................................112

5-8-4 Intel UPI POST Codes .......................................................................................... 113

- 9 -

5-8-5 Intel UPI Error Codes ...........................................................................................113

5-8-6 Intel MRC POST Codes .......................................................................................114

5-8-7 Intel MRC Error Codes .........................................................................................114

5-8-8 Intel PM POST Codes ..........................................................................................115

5-8-9 Intel PM POST Codes ..........................................................................................115

5-9 BIOS POST Beep code (AMI standard) ....................................................... 116

5-9-1 PEI Beep Codes ...................................................................................................116

5-9-2 DXE Beep Codes .................................................................................................116

5-10 BIOS Recovery Instruction ........................................................................... 117

This page intentionally left blank

- 11 - Hardware Installation

1-1 Installation Precautions

The motherboard/system contain numerous delicate electronic circuits and components which

can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully

read the service guide and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap, keep your hands dry and rst touch a metal object to eliminate static electricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

Hardware Installation - 12 -

1-2 Product Specications

CPU 2nd Generation Intel® Xeon® Scalable and Intel® Xeon® Scalable Processors

Intel® Xeon® Platinum Processor, Intel® Xeon® Gold Processor, Intel® Xeon®

Silver Processor and Intel® Xeon® Bronze Processor

NOTE: If only 1 CPU is installed, some PCIe or memory functions might be

unavailable

Chipset Intel C621 Express Chipset

Memory 16 x DIMM slots

DDR4 memory supported only

6-channel memory per processor architecture

RDIMM modules up to 64GB supported

LRDIMM modules up to 128GB supported

Supports Intel® Optane™ DC Persistent Memory (DCPMM)

1.2V modules: 2933/2666/2400/2133 MHz

Maximum veried DCPMM conguration:

* Ambient temperature 35°C

* 2nd Generation Intel® Xeon® Scalable processor 145W (Max.)

* DCPMM 256GB x4 pcs

DCPMM installation locations:

DIMM_P0_( A1, D1)

DIMM_P1_( G1, J1)

NOTE:

1. 2933MHz for 2nd Generation Intel® Xeon® Scalable Processors only

2. Intel® Optane™ DC Persistent Memory for 2nd Generation Intel® Xeon®

Scalable Processors only

3. The maximum number of DCPMM that can be installed is based on a

maximum operating (ambient) temperature of 35°C

4. To enquire about installing a greater number of DCPMM, please consult with

your GIGABYTE technical or sales representative

LAN 2 x 10Gb/s SFP+ LAN ports (QLogic® QL41102)

2 x 1Gb/s LAN ports

1 x 10/100/1000 management LAN

- 13 - Hardware Installation

Expansion Slot Slot_7 (PCIe_4): 1 x PCIe x16 (Gen3 x16 bus) slot from CPU_1

Slot_6 (PCIe_3): 1 x PCIe x16 (Gen3 x16 bus) slot from CPU_1

Slot_5 (PCIe_2): 1 x PCIe x16 (Gen3 x16 bus) slot from CPU_1

Slot_4 (PCIe_1): 1 x PCIe x16 (Gen3 x16 bus) slot from CPU_0

1 x Mezzanine card slot:

- PCIe Gen3 x16 (x8+x8)

- From CPU_0

- Optional for OCP mezzanine card with low prole type

Video Integrated in Aspeed® AST2500

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Storage Front side: 24 x 3.5" or 2.5" SATA/SAS hot-swappable HDD/SSD bays

Rear side: 12 x 3.5" or 2.5" SATA/SAS hot-swappable HDD/SSD bays

Rear side booting device bay: 2 x 2.5" hot-swappable SSD bays*

NOTE:

*For rear side 2.5" bays support Solid State Drives only due to thermal

consideration

2 x Broadcom SAS3x36R expanders

Bandwidth: SATAIII 6Gb/s or SAS 12Gb/s per port

Default conguration supports:

2 x SAS/SATA drives in rear side

SAS card is required to enable the drive bays

Suggested 12Gb/s SAS cards:

CRA4648

CSA4648

SAS Depends on SAS Card

Internal I/O 2 x SATA 7-pin connectors

1 x TPM header

1 x VROC connector

Front I/O 2 x USB 3.0

1 x Power button with LED

1 x ID button with LED

1 x NMI button

1 x System status LED

4 x LAN activity LEDs

Hardware Installation - 14 -

Rear I/O 2 x USB 3.0

1 x VGA

2 x SFP+

2 x RJ45

1 x MLAN

1 x ID button with LED

2 x LAN activity LEDs

Backplane I/O Bandwidth: SATAIII 6Gb/s or SAS 12Gb/s per port

TPM 1 x TPM header with SPI interface

Optional TPM2.0 kit: CTM010

System

Management

Aspeed® AST2500 management controller

GIGABYTE Management Console (AMI MegaRAC SP-X) web interface

Dashboard

JAVA Based Serial Over LAN

HTML5 KVM

Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)

Sensor Reading History Data

FRU Information

SEL Log in Linear Storage / Circular Storage Policy

Hardware Inventory

Fan Prole

System Firewall

Power Consumption

Power Control

LDAP / AD / RADIUS Support

Backup & Restore Conguration

Remote BIOS/BMC/CPLD Update

Event Log Filter

User Management

Media Redirection Settings

PAM Order Settings

SSL Settings

SMTP Settings

Hardware Installation - 15 -

Power Supply 2 x 1200W redundant PSUs

80 PLUS Platinum

AC Input:

- 100-240V~/ 12-7A, 50-60Hz

DC Input:

- 240Vdc/ 6A

DC Output:

- Max 1000W/ 100-240V~

+12V/ 80.5A

+12Vsb/ 3A

- Max 1200W/ 200-240V~ or 240Vdc input

+12V/ 97A

+12Vsb/ 3A

Environment

Ambient

Temperature

Relative

Humidity

Operating temperature: 10°C to 35°C

Operating humidity: 8-80% (non-condensing)



Non-operating temperature: -40°C to 60°C

Non-operating humidity: 20%-95% (non-condensing)

System

Dimension

4U

482.6mm (W) x 177mm (H) x 625mm (D)

* We reserves the right to make any changes to the product specications and product-related information without

prior notice.

- 16 - Hardware Installation

1-3 System Block Diagram

2 x USB 3.0

(rear side)

PCIe3.0 x16

UPI 10.4GT/s

2A~2D

Slot_7: PCIe x16 (Gen3 x16)

Slot_6: PCIe x16 (Gen3 x16)

Slot_5: PCIe x16 (Gen3 x16)

Slot_4: PCIe x16 (Gen3 x16)

PCIe3.0 x16

PCIe3.0 x8

2 x 1GbE

Base-T LAN

2 x 10GbE

SFP+ LAN

Q-Logic

(QL41102)

PHY

Intel

X722

Intel

X722

PCIe3.0 x1

SPI

ASPEED

AST2500

MLAN MAC

BMC

2 x SSATAIII

(SATA DOM)

8 x SATAIII

3 x SlimSAS

2 x SSATAIII

4 x SSATAIII

Uplink x1

DMI3 x4

2 x USB 3.0

2 x USB 2.0

2 x USB 3.0

PCH

Intel C621

Lewisburg

Switch

PCIe3.0 x8

COM

VGA

OCP Mezzanine

2 x SlimSAS 4i

Skylake SP

Cascade Lake SP

LGA3647 (Socket P0)

CPU0

Skylake SP

Cascade Lake SP

LGA3647 (Socket P1)

CPU1

6-Channel DDR4, 8 x DIMMs

2933(1DPC)/2666/2400 MHz

6-Channel DDR4, 8 x DIMMs

2933(1DPC)/2666/2400 MHz

10/100/1G

PHY(1ch)

SW_RAID

for VROC

TPM

2-bay 2.5” SATA

(rear side)

SAS Card (HW or SW RAID)

12-bay 3.5" SAS/SATA (rear side)

expander

optional

4 x SAS3.0

24-bay 3.5" SAS/SATA (front side)

- 17 - System Appearance

HDD1

HDD5

HDD9

HDD13

HDD17

HDD21

HDD2

HDD6

HDD10

HDD14

HDD18

HDD22

HDD3

HDD7

HDD11

HDD15

HDD19

HDD23

HDD4

HDD8

HDD12

HDD16

HDD20

HDD24

Chapter 2 System Appearance

2-1 Front View

No. Description

1. Front Panel LEDs and buttons

2. Reset Switch

3. Front USB 3.0 ports

• Refer to Chapter 2-3 Front Panel LED and Buttons for a detailed description of the function

of the LEDs.

System Appearance - 18 -

2-2 Rear View

No. Description

1. USB 3.0 Port x 2

2. 10/100/1000 Server management LAN port

3. VGA Port

4. 10Gbe LAN Port x 2

5. ID Button with LED

6. 10Gbe LAN Port x 2

7. PCIe Card Bay x 7

• Refer to Chapter 2-4 Rear System LAN LEDs for a detailed description of the function of

the LEDs.

HDD25

HDD29

HDD33

HDD26

HDD30

HDD34

HDD_OS1

HDD_OS2

HDD27

HDD31

HDD35

HDD28

HDD32

HDD36

Primary PSU

Secondary PSU

1 2 4 5 6 73

• HDD_OS1 and HDD_OS2 are 2.5" hard drives while the remaining hard drives on the front and

rear side of the server are 3.5" hard drives.

- 19 - System Appearance

2-3 Front Panel LED and Buttons

LAN1 LAN2

LAN3

RSV

LAN4

No. Name Color Status Description

1. Power button

with LED

Green On Indicates the system is powered on.

Green Blink System is in ACPI S1 state (sleep mode).

N/A Off • System is not powered on or in ACPI S5 state (power off)

• System is in ACPI S4 state (hibernate mode)

2. LAN1 Active/

Link LED

Green On Indicates a link between the system and the network or

no access.

Green Blink Indicates data trasmission or receiving is occuring.

N/A Off Indicates no data transmission or receiving is occuring.

3. LAN3 Active/

Link LED

Green On Indicates a link between the system and the network or

no access.

Green Blink Indicates data trasmission or receiving is occuring.

N/A Off Indicates no data transmission or receiving is occuring.

4. Reserved

button N/A N/A The button's is reserved for custom functions and behavior.

5. ID Button

with LED

Blue On Indicates the system identication is active.

N/A Off Indicates the system identication is disabled.

6. LAN2 Active/

Link LED

Green On Indicates a link between the system and the network or

no access.

Green Blink Indicates data trasmission or receiving is occuring.

N/A Off Indicates no data transmission or receiving is occuring.

8. LAN4 Active/

Link LED

Green On Indicates a link between the system and the network or

no access.

Green Blink Indicates data trasmission or receiving is occuring.

N/A Off Indicates no data transmission or receiving is occuring.

System Appearance - 20 -

8. System

Status LED

Green On Indicates system is operating normally.

Amber

Indicates a critical condition, may include:

-System fan failure

-System temperature

Blink

Indicates non-critical condition, may include:

-Redundant power module failure

-Temperature and voltage issue

N/A Off

Indicates system is not ready, may include:

-POST error

-NMI error

-Processor or terminator is missing

Page is loading ...

Gigabyte S451-3R0 User manual

Gigabyte S451-3R0 User manual

Gigabyte S451-3R0 User manual

Related papers

Other documents