Primo International EZ Base Assembly Instructions Manual

Brand: Primo International

Model: EZ Base

Type: Assembly Instructions Manual

EZBaseAssembly

Instructions

STEP1

Openthepackagingattheend

wherethehandleisandidentify

thelocationoftheupholstered

framesinsidethepackaging.

WeatPrimoInternationalwouldliketothankyouforyour

purchase.

Nowthatyournewproducthasbeendeliveredto

you,letushelpyouthroughitsassemblysoyoucanenjoyitfully.

STEP2

Openthepackagingaftermakingsuretheupholstered

framesinsidetheboxareontheoppositesidetoavoiddamaging

thematerial.

STEP3

Removeallpiecesfromthepackagingandmakesurethereis

nothingleftinsidethecartonbeforedisposingofit.Pleasepay

attentiontoanysmallhardwarethatcouldhavecomeloose.

STEP4

Removethecomponentsfromtheprotectivematerialandplace

themonaclean,flatandlevelledsurface,thisisimportant.

Theboxshouldcontainthefollowingpieces:

2xSideframes(A)

2xEndframes(B)

1xCenterrail(C)

10xSlats(D)

1xCover(E)

1xHardware(F)

pack

STEP5

IdentifythecontentoftheHardwarepack(F):

4xLegs(H)

4xCornerbrackets(I)

1xSupportleg(J)

2xHeadboard

bracket(K)

2xCenterrail

Bracket(L)

H I

26xBolts(M)

26xWashers(N)

4xCarriagebolts(O)

4xFlatwashers(P)

4xNuts(Q)

4xWoodscrews(R)

1xSpanner(S)

1xAllenkey(T)

RS T

IMPORTANTNOTE

Donotuseapowertooltoassemblethisproductasitcould

damagethethreadofthehardwareandaffectthesolidity/durability

oftheproduct.

STEP6

Nowthatyouhaveidentifiedallcomponents,wecanstartthe

assemblyprocessbutfirst,paycloseattentiontothefollowing

detail:

IMPORTANTNOTE

Thecornerbracketsarefittedwithroundholesandroundedrectangle

holes.TheroundholesmustbeusedtoattachthebrackettotheSide

Frames(A)andtheroundedrectangleholesusedtoattachthebracket

totheEndframes(B)

Roundhole

Roundedrectangle

hole

STEP7

Usethebolt(M)andwasher(N)toattachthe2centerrailbracket(L)to

theendframes(B).Thebracketmustbeinstalledupwardasillustrated

below.Adjustthebracketstobestraightandlevelagainstthetopofthe

frameandtightenusingtheAllenkey(T)

NLT

STEP8

Attachthe4cornerbrackets(I)tothe2endframes(B)withthe

bolts(M)andwashers(N)usingtherounded

rectangleholes. Donotfullytighten theboltsatthisstage,leave

themloose.

Rounded

rectangle

hole

Thebottomofthecorner

bracketisfittedwithaplate

wherethelegswillattachon.

Insuretopositionthebracket

sotheplateisatthesame

leveltothebottomofthe

frame.

STEP9

Attachthesideframe(A)

totheendframe(B)using

bolts(M)andwashers(N)

Leavetheboltloose,

donottightenatthis

stageoftheassembly

STEP10

Completeattachingallframesbutleaveallboltsloose

STEP11

Adjusteachcornersotheendonthesideframe(A)correctlylines

upwithendofendframe(B)thenthightenthebolts.

STEP12

Puttheframeonitsside

andattachthelegs(H)to

thecornerbracketsbase

Onceall4legshavebeenattached,pleasere‐checkthatallboltsare

evenlytighten.

STEP13

Takethecenterrail(C)andthesupportleg(J).

Locatetheattachmentscrewsonthecenterrail

Attachthesupportleg(J)tothecenterrail(C)usingthebolts(M)

andwashers(N).VERYIMPORTANT,theboltsmustbeattachedfrom

theoppositesideofwheretheattachmentnutisflushagainsttherail.

Thisisthewrongside.

Correctsidetoattachthe

supportleg

STEP14

Oncethesupportlegisattachedto

thecenterrail,placethecenterrail

inthecenterrailbrackets.

STEP15

2ofthewoodenslats(D)are

fittedwithholeswhichwillbe

usedtoattachthemtotheside

frames.Those2slatsaretobe

placedinthecenterofthebase

asillustratedbelow.

Yournewplatformbasecannowbecovered.

UseaPhillips(starhead)

screwdrivertoattachthe2

middleslatstothesideframes

usingthewoodscrews(R)

LASTSTEP

Usethecover(E)torecovertheframeandvoila,yournew

platformbaseisreadyforuse.

OPTIONALSTEPSFORHEADBOARD

Shouldyoudecidetouseyournewplatformbasewithaheadboard,

therequiredhardwareisalreadyprovidedwiththepackyoureceived.

1st STEP:

Taketheheadboardbracket(K)providedwiththehardwarepack

ofyourbaseandidentifywhichholesonthebracketcorresponds

totheattachmentholesonyourheadboard.

2nd STEP:

Onceyouhaveidentifiedthematchingholes,put1carriagebolt (O)

ineachmatchinghole(Intheillustrationbelow,thewasher(P)and

nut(N)areusedtokeepthecarriageboltsinplaceonly)

3rd STEP:

Attachtheheadboardbracket(K)totheendframe(B)thatisalready

fittedwithpre‐drilledholesusingthebolts(M)andwashers(N).

Adjusttheheightofthebraketbyslidingitupordown.Onceatthe

desiredheight,makesurethebracketisstraightandtightenthebolts.

4th STEP:

Youcanslidethecarriagebolts

side‐to‐sidetofitintothehead‐

boardattachmentholesafter

removingthenutandwasher.

Oncetheheadboard(not

Illustrated)isinplace,usethe

spanner(S) totightenittothe

headboardbracketsusingthe

Washers(P)andnuts(Q).

Primo International EZ Base Assembly Instructions Manual

Brand: Primo International

Model: EZ Base

Type: Assembly Instructions Manual

Download PDF

report

Primo International EZ Base Assembly Instructions Manual

Primo International EZ Base Assembly Instructions Manual

Other documents