ML Knightsbridge HBL Series User manual

Brand
ML
Model
Knightsbridge HBL Series
Type
User manual

This manual is also suitable for

1
122
INSTALLATION & MAINTENANCE MANUAL
HBL series
IP
65
230V
50Hz
2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
HBL100 / HBL150 / HBL200 / HBL240
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this luminaire should only be carried out by a qualified electrician or competent
person to the latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for
installation
• This product series is Class I and requires an earth
• This product series is IP65 rated (recommended indoor use only)
• This product is dimmable via a 1-10V dimmer
• Provide power to the required point of installation. Suitable IP rated junctions boxes should be used
where required
Suspension mounting
• To suspend the fitting, screw the mounting hoop into the top of the luminaire (see Fig 1)
HBLseries
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:
HBL100/HBL150/HBL200/HBL240
SAFETY
• Installationofthisluminaireshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductseriesisClassIandrequiresanearth
• ThisproductseriesisIP65rated(recommendedindooruseonly)
• Thisproductisdimmableviaa1-10Vdimmer
INSTALLATION
• Providepowertotherequiredpointofinstallation.SuitableIPratedjunctionsboxesshouldbeusedwhere
required
Suspensionmounting
• Tosuspendthefitting,screwthemountinghoopintothetopoftheluminaire(seeFig1)
Fig1
Bracketmounting
• Usingthebracketasatemplate,markthelocationofthefixingholes,drill2x10mmholesensuringnotto
infringewithanyjoists,gasorwaterpipesorelectricalcables
• Usingahammer,taptheexpansionboltsintothe10mmfixingholes(seeFig2)
Fig2
Screwdown
mountinghoop
Fig 1
3
Bracket mounting
• Using the bracket as a template, mark the location of the fixing holes, drill 2 x 10mm holes
ensuring not to infringe with any joists, gas or water pipes or electrical cables
• Using a hammer, tap the expansion bolts into the 10mm fixing holes (see Fig 2)
• Tighten expansion bolt nuts but allow enough space for the bracket to mount
• Remove the driver housing via the 4 Allen screws (see Fig 3)
• Align the mounting bracket with 2 of the driver housing screw pillars (see Fig 4)
HBLseries
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproducts:
HBL100/HBL150/HBL200/HBL240
SAFETY
• Installationofthisluminaireshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductseriesisClassIandrequiresanearth
• ThisproductseriesisIP65rated(recommendedindooruseonly)
• Thisproductisdimmableviaa1-10Vdimmer
INSTALLATION
• Providepowertotherequiredpointofinstallation.SuitableIPratedjunctionsboxesshouldbeusedwhere
required
Suspensionmounting
• Tosuspendthefitting,screwthemountinghoopintothetopoftheluminaire(seeFig1)
Fig1
Bracketmounting
• Usingthebracketasatemplate,markthelocationofthefixingholes,drill2x10mmholesensuringnotto
infringewithanyjoists,gasorwaterpipesorelectricalcables
• Usingahammer,taptheexpansionboltsintothe10mmfixingholes(seeFig2)
Fig2
Screwdown
mountinghoop
• Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount
• Removethedriverhousingviathe4Allenscrews(seeFig3)
Fig3
• Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)
Fig4
• PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown
the4Allenscrews(seeFig5)
Fig5
Removethe4Allenscrews
FastendownAllenscrews
Removethe4Allenscrews
FastendownAllenscrews
Fig 2
Fig 3
Fig 4
4
• Tightenexpansionboltnutsbutallowenoughspaceforthebrackettomount
• Removethedriverhousingviathe4Allenscrews(seeFig3)
Fig3
• Alignthemountingbracketwith2ofthedriverhousingscrewpillars(seeFig4)
Fig4
• PositionthedriverhousingintothebracketensuringallAllenscrewholesarecorrectlyalignedandfastendown
the4Allenscrews(seeFig5)
Fig5
Removethe4Allenscrews
FastendownAllenscrews
• Liftthefittinguptotheexpansionboltsandslideintothebracket(seeFig6)
Fig6
• Tightenthe2expansionboltstosecuretheluminairetothesurface
Towiretheluminairewithoutadimmer(seefig7)
Fig7
Towiretheluminairewitha1-10Vdimmer(seeFig8)
Live-brown
Earth–green/yellow
Neutral-blue
Blue:Dim+
White:Dim-
Neutral-blue
Earth–green/yellow
Live-brown
• Liftthefittinguptotheexpansionboltsandslideintothebracket(seeFig6)
Fig6
• Tightenthe2expansionboltstosecuretheluminairetothesurface
Towiretheluminairewithoutadimmer(seefig7)
Fig7
Towiretheluminairewitha1-10Vdimmer(seeFig8)
Live-brown
Earth–green/yellow
Neutral-blue
Blue:Dim+
White:Dim-
Neutral-blue
Earth–green/yellow
Live-brown
• Position the driver housing into the bracket ensuring all Allen screw holes are correctly
aligned and fasten down the 4 Allen screws (see Fig 5)
• Lift the fitting up to the expansion bolts and slide into the bracket (see Fig 6)
• Tighten the 2 expansion bolts to secure the luminaire to the surface
To wire the luminaire without a dimmer (see fig 7)
Fig 5
Fig 6
Fig 7
5
• Liftthefittinguptotheexpansionboltsandslideintothebracket(seeFig6)
Fig6
• Tightenthe2expansionboltstosecuretheluminairetothesurface
Towiretheluminairewithoutadimmer(seefig7)
Fig7
Towiretheluminairewitha1-10Vdimmer(seeFig8)
Live-brown
Earth–green/yellow
Neutral-blue
Blue:Dim+
White:Dim-
Neutral-blue
Earth–green/yellow
Live-brown
Fig8
TowiretheluminairewithHBLS(seeFig9)

Fig9
Neutral-blue
Live-brown
Neutral-blue
Earth–green/yellow
White:Dim-
Blue:Dim+
Live-brown
Switchedlive-yellow
Attachthemicrowavesensor
mountingbracketusingthe
5xscrewsprovided
Black
To wire the luminaire with a 1-10V dimmer (see Fig 8)
To wire the luminaire with HBLS (see Fig 9)
Fig 8
Fig 9
Red
6
INSTALLATION
Detection area
Detection area can be adjusted from a maximum range of 15 meters down to 7 meters by observing
the below settings
Hold time
Hold time refers to the time that the luminaire will remain at 100% brightness after no motion is
detected
Standby period
Refers to the time period that the luminaire will remain at low light level in the absence of movement
If set to “DISABLE”, the low light level will permanently be maintained until motion is detected
S1 Detection
Area
On 100%
- 50%
ON
S2 S3 S4 HOLD TIME
On On On 5sec
- On On 30sec
On - On 90sec
- - On 3min
On On - 20min
- - - 30min
S5 S6 S7 STANDBY
PERIOD
On On On DISABLE
- On On 60min
On - On 30min
- - On 10min
On On - 5min
- - - 5sec
ON
ON
7
ON
ON
Standby dimming level
This setting refers to the light level you require once “hold time” has elapsed
Daylight sensor
This setting is to set the ambient light level you would require the luminaire to operate in, selecting
“DISABLE” would enable the luminaire to operate at all times regardless of ambient light levels
Do not use any source of high pressure washers to maintain or clean this luminaire
Ensure correct fixtures are used for the surface that the luminaire is fixed to
This luminaire is recommended for indoor use only
• Switch on and check for correct operation
S8 S9 STANDBY
DIMMING LEVEL
On On 50%
- On 30%
On - 20%
- - 10%
S10 S11 S12 DAYLIGHT SENSOR
On On On DISABLE
- On - 200lx
On - - 100lx
- - - 50lx
WARNING
ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk SBFEB17_V2
8
GENERAL
WARRANTY
The unit should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the product
Be aware that these products may require an MCB upgrade to a type C due to high inrush currents
This product has a warranty of 5 years from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period it
should be returned to the place of purchase for a free of charge replacement. ML Accessories does
not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ML Knightsbridge HBL Series User manual

Brand
ML
Model
Knightsbridge HBL Series
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents