PACK 11
STAGE P.
87 THE FRONT LIGHTS – 3 214
88 THE CAR BODY 216
89 THE WINDSCREEN 220
90 THE REAR WINDOW 222
91 THE ROOF PANEL 224
92 THE SEAT BELTS 226
93 THE BOOT LINER 230
94 JOINING THE PLATFORM
AND THE CAR BODY 234
95 THE REAR LIGHTS – 1 240
Designed and produced by Milanoedit srl – www.milanoedit.com
Published by De Agostini Publishing S.p.A., 28100 Novara,
Via G. da Verrazzano 15
All rights reserved © 2020
NOT SUITABLE FOR CHILDREN UNDER THE AGE OF 14.
THIS PRODUCT IS NOT A TOY AND MUST BE USED UNDER
THE SUPERVISION OF AN ADULT.
ITEMS MAY VARY FROM THOSE SHOWN.
❷
❶
❸
❺ ❻
❹
THE FRONT LIGHTS – 3
87
In this stage you will continue to work on your model’s front lights.
❺
❻
❶
❷
❸
❹
❺
❻
Wheel arch
Wiring
Front light unit
Pipe
Screws A (2.3 x 6mm) x2
Screws B (2.3 x 4mm) x2
Attach the pipe to the wheel arch, positioning the pieces as shown in the photo. Check that you have attached the components correctly.
Step
1
COSMO SPORT
The pipe
TOOLS NEEDED
• Cross screwdriver no. 1
• Modelling glue
INDICATOR
❶
❹
RECOMMENDED TOOLS
• T o o t h p i c k s
LIST OF PIECES
Stage 87Pack 11
214
Step
2
COSMO SPORT
The wiring – 1
Step
3
COSMO SPORT
The wiring – 2
Attach the circuit board (wiring 2, plug marked C2)
that you received with stage 85 to the wheel arch.
Make sure the screw holes are aligned.
Secure the pieces with
one of the screws you
received with stage 85.
Attach the circuit board, positioning the pieces
as shown in the photo.
Be careful not to damage the components
of the circuit board.
Apply a drop of glue, as shown in the photo,
to secure the circuit board to the car body.
This is the result of this
assembly session. As always,
keep the pieces
in a safe place.
FINAL RESULTFINAL RESULT
❷
❷
❶
❷ Stage 85
You have now installed both of the circuit
boards for the front lights.
The next stage
Stage 87Pack 11
215
THE CAR BODY
88
You have finally received the main body of your model, so in this stage
you will attach the doors and other components you worked on in the
previous stages.
❶
❷
❸
Main body
Screws A (2.3 x 4mm) x5
Screws B (2.3 x 4mm) x6
❷
❸
Attach the boot lid you worked on in stage 84 to the body.
Turn the body over and place one of the mount brackets you received
with stage 84 in the position shown in the photo.
Secure the pieces together
with one of the screws you
received with stage 84.
Step
1
COSMO SPORT
The car body – 1
TOOLS NEEDED
• Cross screwdriver no. 1
• Adhesive tape
CAR BODY
❹ Stage 84
❶
❷
❶
❸
LIST OF PIECES
Stage 88Pack 11
216
Step
2
COSMO SPORT
The car body – 2
Step
3
COSMO SPORT
The car body – 3
Check that the boot lid opens and closes smoothly.
Now attach the second mount bracket you received with stage 84, as shown in the photo. Secure the pieces together with another of the screws
you received with stage 84.
To avoid damaging any components during the next few sessions, apply two strips of
adhesive tape to keep the boot lid closed.
❹ Stage 84
Stage 88Pack 11
217
Step
4
Step
5
COSMO SPORT
COSMO SPORT
The car body – 4
The car body – 5
Now secure the door
windows with adhesive tape.
This way, you will avoid
damaging any components
while working on your model.
Attach the left door to the
car body, positioning
the pieces as shown
in the photo.
Secure the pieces together
with two type A screws.
Now attach the right door to the car body.
Secure the pieces together with two type A screws.
Apply another strip of adhesive tape
to secure the door.
Apply another strip of adhesive tape
to secure the door.
❶
❷
❷
Stage 88Pack 11
218
This is what your model’s
body looks like at the end of
this assembly session. Keep
it in a safe place with the rest
of the pieces.
FINAL RESULTFINAL RESULT
The next stage
Step
7
COSMO SPORT
The car body – 7
From the inside of the car body, insert and tighten
one type B screw in the circled hole.
Now insert and tighten two type B
screws in the holes circled in the photo.
Insert and tighten two
more type B screws in the
holes circled in the photo.
Step
6
COSMO SPORT
The car body – 6
Get the front section of the body and attach it to the main
section, positioning the pieces as shown in the photo.
We recommend you secure the bonnet with two strips of adhesive tape.
❶
❸
Stage 88Pack 11
219
THE WINDSCREEN
89
In this stage you will attach the windscreen to the body of your 1:8 scale
Mazda Cosmo Sport model.
❶
❷
Windscreen
Screws (2.3 x 4mm) x3
Attach the windscreen to the car body,
positioning the pieces as shown
in the photo.
Turn the body over and insert one
of the screws you received with this stage
in the circled hole. Don’t fully tighten it.
Now insert a second screw into the hole
circled in the photo. Again, don’t fully
tighten it.
Step
1
COSMO SPORT
The windscreen – 1
TOOLS NEEDED
• Cross screwdriver no. 1
WINDSCREEN
❷
❶
❶
LIST OF PIECES
Stage 89Pack 11
220
Step
2
COSMO SPORT
The windscreen – 2
Step
3
COSMO SPORT
The windscreen – 3
To attach the top of the windscreen to the body, push it in
the direction indicated by arrow A and press at the point
indicated by arrow B.
Now you can tighten the two screws you inserted in step 1. Be careful: over-tightening the screws
could damage the components.
Do the same on the other side of the windscreen.
Finally, press the top of the windscreen in the middle.
B
B
A
A
FINAL RESULTFINAL RESULT
The next stage
This is the result of this
assembly session.
As always, keep the
pieces in a safe place.
Stage 89Pack 11
221
THE REAR WINDOW
90
In this stage you will attach the rear window to the car body, in more
or less the same way you attached the windscreen in the previous
assembly session.
❶
❷
❸
Rear window
Screws (2.3 x 4mm) x3
Stickers
Attach the rear window to the body, positioning the pieces as shown in the photo. Turn the body over and secure the pieces together
with two of the screws you received with this stage.
Do not fully tighten the screws.
Step
1
COSMO SPORT
The rear window – 1
TOOLS NEEDED
• Cross screwdriver no. 1
REAR WINDOW
RECOMMENDED TOOLS
• T w e e z e r s
• Cotton wool / cotton buds
❶
❷
❶
❸
LIST OF PIECES
Stage 90Pack 11
222
Step
2
COSMO SPORT
The rear window – 2
Step
4
COSMO SPORT
The stickers – 2
Step
3
COSMO SPORT
The stickers – 1
To attach the top of the rear window to
the body, push it in the direction indicated
by arrow A and press on the point indicated
by arrow B.
Do the same on the other side
of the rear window.
Now you can fully tighten the
screws you inserted in step 1.
Attach the sticker to the platform of
your model, as shown in the photo.
Again, use a piece of cotton wool
or a cotton bud to secure it firmly
to the platform.
Attach the sticker to the platform of
your model, as shown in the photo.
Gently press on the sticker with
a piece of cotton wool or a cotton
bud, so that it attaches firmly
to the platform.
Now remove the other sticker from its backing.
Remove the sticker shown in the photo from
its backing.
This is the result of this
simple assembly session.
Keep everything
in a safe place with
the rest of the pieces.
FINAL RESULTFINAL RESULT
The next stage
B
B
AA
❸
❸
❸
❸
Stage 90Pack 11
223
THE ROOF PANEL
91
In this stage you will attach a panel to the underside of your model’s roof.
❶
❷
❸
Panel
Double-sided adhesive tape
Screws (2.3 x 4mm) x3
Remove the paper backing from one side
of the double-sided tape. Attach the tape
to the panel, as shown in the photo, and then
remove the second piece of paper backing.
You are now going to attach the
panel to the body. Position the
pieces as shown in the photo.
Step
1
COSMO SPORT
The panel – 1
TOOLS NEEDED
• Cross screwdriver no. 1
PANEL
RECOMMENDED TOOLS
• T w e e z e r s
❶
❷
Make sure the screw
holes in the panel and
the body are aligned,
as shown in the photo.
❷
❶
❸
LIST OF PIECES
Stage 91Pack 11
224
Step
2
COSMO SPORT
The panel – 2
Step
3
COSMO SPORT
The panel – 3
Attach the panel to the body by inserting the small linchpins circled in the photo into the corresponding holes in the panel.
Insert and tighten two of the screws
received with this stage in the circled holes.
Press the middle of the panel to attach it firmly to the body.
This is the result of this
simple assembly session.
The body is almost ready
to be attached to the
rest of your model.
FINAL RESULTFINAL RESULT
The next stage
Stage 91Pack 11
225
THE SEAT BELTS
92
In this assembly session you will install your model’s seat belts.
Follow our instructions and explanatory photographs very carefully.
❶
❷
❸
❹
❺
❻
❼
Seat belts (parts A)
Seat belts (parts B)
Seat belt (part C)
Seat belt (part D)
Aerial
Rear-view mirror
Rear air vents (R and L)
Look at the photo carefully to familiarise
yourself with the seat belts. The top
seatbelt in the photo shows the front
of parts A.
Now attach one of the parts A, positioning
the pieces as shown in the photo.
Arrange part D of the left seat belt on your work
surface.
Arrange part A as shown in the photo.
Step
1
COSMO SPORT
The seat belts – 1
TOOLS NEEDED
• Scissors
• Ruler
SEAT BELTS
❹
❶
❹
❷
❶
❸
❺❻ ❼
❹
RECOMMENDED TOOLS
• Modelling glue
LIST OF PIECES
Stage 92Pack 11
226
Step
2
COSMO SPORT
The seat belts – 2
Step
3
COSMO SPORT
The air vents
Insert the free end of part A into the buckle, as shown in the photo.
Look at the photo to help you adjust the length
of part A.
Repeat the previous steps to assemble
the right seat belt, using the second part A
and part C.
Cut off the excess piece of part A,
as shown in the photo.
Get the body of your model and attach the two air vents to it, positioning the pieces as shown in the photo.
❼
❶
Stage 92Pack 11
227
Insert the linchpins on the buckle into the corresponding holes in the body, as shown in the photo.
You will now attach the right seat belt (shown in the photo)
to the body.
Attach the rear-view mirror to the car body, positioning the
pieces as shown in the photo.
Be careful not to damage the components as you work on them.
Attach the left seat
belt to the car body
in the same way.
Step
4
Step
5
COSMO SPORT
COSMO SPORT
The seat belts – 3
The rear-view mirror
❻
Stage 92Pack 11
228
Step
7
COSMO SPORT
The seats
This is the result of this
satisfying assembly session.
As always, keep the pieces
in a safe place.
FINAL RESULTFINAL RESULT
The next stage
Now you can finally attach the seats
to the platform: start with the driver’s
side, as shown in the photo.
Now attach the passenger seat.
Arrange parts B of the
seat belts over the seats,
as shown in the photo.
Position one of the parts B as shown
in the photo.
Insert the buckle into the circled hole in the platform.
Do the same with the second part B
on the other side of the platform.
Step
6
COSMO SPORT
The seat belts – 4
❷
❷
Stage 92Pack 11
229
THE BOOT LINER
93
In this assembly session you will install a mat that acts as the boot liner
of your model. You will also replace the front suspension springs with the
two you received with this stage.
❶
❷
❸
❹
❺
❻
❼
❽
Mat part A
Mat part B
Mount bracket
Cap
Body detail
Lock
Screws (2.3 x 4mm) x3
Springs
Position the mount bracket as shown in the photo.Attach the detail to the body, positioning the pieces
as shown in the photo.
Secure the pieces together with two of the screws received
with this stage.
Step
1
COSMO SPORT
Details – 1
TOOLS NEEDED
• Cross screwdrivers no. 1 and 2
BOOT
RECOMMENDED TOOLS
• F i l e
❸
❺
❷❶
❸❺ ❻ ❽
❹❼
LIST OF PIECES
Stage 93Pack 11
230
Now attach the lock to the body, positioning the pieces
as shown in the photo.
Remove the strip of adhesive tape securing the jack handle.
Press until the pieces click together.
Place part B of the mat on the floor of the boot.
If necessary, you can enlarge the holes of the lock slightly
with a file.
Check that the holed linchpins are inserted into the holes
in part B.
Step
2
Step
3
COSMO SPORT
COSMO SPORT
Details – 2
The mat – 1
❻
❷
Stage 93Pack 11
231
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
