Champion Industries, Inc.
P. O. Box 4149, Winston-Salem, NC 27115
Tel: 336/661-1556 Fax: 336/661-1979
www.championindustries.com
Project
Item No.
Quantity
Champion Industries, Inc.
2674 N. Service Road,
Jordan Station, Ontario, Canada L0R 1S0
Tel: 905/562-4195 Fax: 905/562-4618
(1M) 3/10 Printed in U.S.A.
CH070
SPECIFIER STATEMENT
Specified unit will be a Champion model 54 DR
Series high temperature dual rinse rack conveyor
dishwashing machine. Features top mounted control
cabinet; upper and lower one-piece stainless steel spray
arm assemblies, removable internal scrap basket with
three-piece scrap screen. Large 26" front access
door and double-hook safety latch (Prewash unit
has additional 15 1/2" or 26" wash door). Anti-jam
conveyor drive system.
1 year parts and labor warranty.
Model 54 DR Shown with
Vent Cowl and Damper Option
STANDARD FEATURES
• ENERGY STAR® Qualified
• Exclusive DualRinse Technology
• Dual-pawl cradle drive system
• One-piece cast stainless steel upper
& lower spray arm assemblies
• Internal removable scrap basket and
three-piece scrap screen
• Standard vertical opening accommodates
18" x 26" sheet pans
• Wide 26" leakproof doors on wash tank
• Anti-jam conveyor drive system
• Energy Sentinel (Idle pump shut-off)
• Convenient top-mounted controls
• Automatic tank fill
• Door safety switch
• Door activated drain closure
• Enclosure panels (front and sides)
• Splash shields
• Stainless steel heavy-gauge construction,
including base and feet
• Electric tank heat
• Wash pump 2 Hp motor
• Stainless steel pump and impeller
• Single-point electrical connection
• Vent fan control switch
• Stainless steel rear manifolds
PREWASH MODELS ONLY
• External prewash scrap basket
• Prewash pump 1 Hp motor
• Wide 15 1/2" leak proof door internally fitted
(22" Prewash)
• Wide 26" leak proof door internally fitted
(36" Prewash)
54 DR SERIES RACK CONVEYOR
The DualRinse feature offers the
Lowest Water/Utility/Chemical Consumption
while circulating a generous
300+ gallons of water for
Consistently Good Results
High-Temperature
Rack Conveyor Dishwashing Machines with
Dual Stage Rinse
54 DR SERIES
54 DR, 76 DRPW, 80 DRFFPW, 90 DRHDPW
SPECIFICATIONS
Capacity
Racks per hr. (NSF rated) 266
Wash tank (US gal.) 21
Conveyor speed (ft/min.) 7.4
Motor Horsepower
Drive 1/6
Wash 2
Dual Rinse 1/10
Water Consumption
US Gal. per hr. (max. use) 115
US Gal. per rack .43
Heating
Tank Heat, electric (kW) 15
DualRinse Tank Heat, electric (kW) 3
Tank heat, steam
(lbs/hr. required at
15 PSI flow pressure) 75
Electric booster (built-in)
(kW supplied for 40°F rise) 12
Electric booster (built-in)
(kW supplied for 70°F rise) 22
Steam booster
(lbs./hr. required for 40°F rise) 60
Steam booster
(lbs./hr. required for 70°F rise) 110
Booster heaters completley inter plumbed,
Controls are interwired
Venting
Load end (minimum CFM) 200
Unload end (minimum CFM) 400
Standard 20" x 20"
rack complement
Peg 2
Flat 1
NEW Exclusive Digital Gauges
Built-in Scrap Basket for ease
of cleaning
One-Piece Cast Stainless Steel
Spray Assembly
Two-Piece Scrap Screen
Stainless Steel
Built-in Nested Booster
NEW Durable Stainless Steel
Start/Stop Switches
LESS IS MORE WITH CHAMPION’S DUAL RINSE MODEL 54 DR SERIES
Check our NSF listings and you’ll see the Dual Rinse offers the lowest water consumption in its class with less than .43 US gallons per
rack. This ENERGY STAR® qualified product brings energy savings. Our 40°F rise booster only requires 12 kW and 70°F rise is only 22 kW.
What the numbers don’t show you is the advantage that our Dual Rinse technology provides by making sure all wares are
fully rinsed with more than 300 gallons per hour while actual fresh water consumption is only 115 gallons per hour.
www.championindustries.com
High-Temperature
Rack Conveyor Dishwashing Machine with
Dual Stage Rinse
54 DR SERIES
54 DR, 76 DRPW, 80 DRFFPW, 90 DRHDPW
10-7/8" [276]
15-7/8" [403]
3-1/4" [83]
2-1/2" [64]
10-1/2" [267]
33-1/2" [851]
8-5/8" [219]
5-1/4" [133]
6" [152]
CLEAR
20"
[508]
89"
[2,261]
DOOR
REMOVAL
HEIGHT
82"
[2,083]
DOOR OPEN
HEIGHT
[1,480]
MACHINE
HEIGHT
58-1/4"
7-1/4"
[184]
5-1/4" [133]
LOAD
HEIGHT
34"
[864]
"
8"
[203]
" [1,372]54
4-1/8" [105]
3-1/4"
[83]
5
26" [660]
DOOR WASH
8A
8B
1A 1B
2
6
7
4A
4A
4B
4B
4-1/8" [105]
8"
[203]
PLUMBING
CLEARANCE
12-3/4"
[324]
7
6
Dimensions shown in inches [mm]
2-1/4" [57]
1-3/4" [44]
1-1/2" [38]
Can be up
to 10" [254]
5/8"
[16]
21" [533]
8" [203]
High-Temperature
Rack Conveyor Dishwashing Machine with
Dual Stage Rinse
54 DR SERIES
Front View
Right to Left
Front View
Left to Right
Plan View
Left to Right
Plan View
Right to Left
End View
Suggested Table
Construction
MODEL 54 DR
54 DR, 76 DRPW, 80 DRFFPW, 90 DRHDPW
Shipping weight crated: 850 lbs.
" [25]1
12-3/8" [314]
37-5/8" [956]
33-1/2" [851]
58-3/8" [1,483]
2-1/8" [54 ] 2-1/8" [54 ]
16"
[406]
18-5/8" [473]
16" [406]
4-3/4" [121]
" [51]2
14-1/2" [368]
1A
1A
1B
1B
2
2
5
5
6
7
4A 4B
VENT STACK DISTANCE
25"
[635]
5-1/4" [133]
8-5/8" [219]
10-7/8" [276]
5-1/4" [133]33-1/2" [851]
PLUMBING
CLEARANCE
12-3/4"
[324]
4-1/8" [105]
4-1/8" [105]
54" [1,372]
6" [152]
8" [203]
8" [203]
15-7/8" [403]
26" [660]
DOOR WASH
[1,480]
MACHINE
HEIGHT
58-1/4"
89"
[2,261]
DOOR
REMOVAL
HEIGHT
82"
[2,083]
DOOR OPEN
HEIGHT
LOAD
HEIGHT
34"
[864]
CLEAR
20"
[508]
3-1/4" [83]
2-1/2" [64]
10-1/2" [267]
3-1/4"
[83]
7-1/4"
[184]
5
8A
8B
1A 1B
2
6
7
4A
4A
4B
4B
7
6
2-1/2" [64] 2-1/2" [64]
20"
[508]
21-7/8"
[556]
" [152] NOMINAL
WALL CLEARANCE
6
26-7/8"
[683]
INSIDE TRACK
OPENING
" [25]1
12-3/8" [314]
37-5/8" [956]
33-1/2" [851]
58-3/8" [1,483]
2-1/8" [54]
2-1/8" [54 ]
16"
[406]
18-5/8" [473]
16" [406]
4-3/4" [121]
" [51]2
14-1/2" [368]
1A
1A
1B
1B
2
2
5
5
67
4A 4B
VENT STACK DISTANCE
25"
[635]
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
2674 N. Service Road, Jordan Station, Ontario, Canada L0R 1S0 • 905/562-4195 • Fax: 905/562-4618
High-Temperature
Rack Conveyor Dishwashing Machine with
Dual Stage Rinse
54 DR SERIES
Dimensions shown in inches [mm]
54 DR, 76 DRPW , 80 DRFFPW, 90 DRHDPW
Shipping weight crated: 923 lbs.
MODEL 76 DRPW WITH 22" PREWASH
MODEL 80 DRFFPW WITH 26" FRONT FREED PREWASH
MODEL 90 DRHDPW WITH 36" HEAVY DUTY PREWASH
Shipping weight crated: 975 lbs.
Shipping weight crated: 1050 lbs.
NOTE: For complete machine dimensions, plan view, end view, specifications and table construction see 54 DR drawing page.
Front View
Front View
Front View
Left to Right
Left to Right
Left to Right
Right to Left
Right to Left
Right to Left
64-3/8"
[1,635]
76"
[1,930]
76DRPW
5
80-3/8" [2,041]
VENT STACK DISTANCE
76" [1,930]
69-1/2" [1,765]
VENT STACK DISTANCE
80-3/8" [2,041]
76DRPW
5
VENT STACK DISTANCE
66-1/2"
[1,689]
80DRFFPW
5
80" [2,032]
77-5/8" [1,972]
65-1/2"
[1,664]
90DRHDPW
VENT STACK DISTANCE
5
94-3/8" [2,397]
90" [2,286]
5
80" [2,032]
71-3/8" [1,813]
VENT STACK DISTANCE
77-5/8" [1,972]
80DRFFPW
5
90" [2286]
82-3/8" [2092]
VENT STACK DISTANCE
94-3/8" [2397]
90DRHDPW
High-Temperature
Rack Conveyor Dishwashing Machine with
Dual Stage Rinse
54 DR SERIES
54 DR, 76 DRPW, 80 DRFFPW, 90 DRHDPW
Plumbing Notes: Because of the variation
in house-supplied steam and water pressures,
steam and water pressure regulating valves
(PRVs) may be needed. (Water PRV is standard on
machines with booster.) The PRVs can either be
purchased from Champion or obtained locally.
Venting Notes: Fabricated duct size:
3-7/8" x 15-7/8" (Outside dimensions)
Warning: Plumbing and electrical
connections should be made by qualified
personnel who will observe all the applicable
plumbing, sanitary, safety codes and the
National Electrical Code.
Note: Water Hammer Arrestor (meeting
ASSE-1010 standard or equivalent) to be
supplied (by others) in common water supply
line at service connection.
54 DR Only
TABLE A - Machine Connection
54 DR Only
TABLE B - Machine & Booster Connection
Utilities
1 Electrical Connection
A Machine electrical connection
B Booster electrical connection
2 Hot Water
Main connection 3/4" NPT
3 Cold Water
Contact Factory
4 Hot Water Tank
A Heat inlet connection 1" NPT
B Heat return connection 1" NPT
5 Drain
Connection 1 1/2" NPT
6 Steam
Inlet connection 1 1/4" NPT
7 Condensate
connection 1" NPT return to boiler
8 Vents
A Stack connection - Load end
150 CFM @ 1/4" static pressure
B Stack connection - Unload end
400 CFM @ 1/4" static pressure
Machine Only
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 70 90 90
240/60/3 62 80 80
480/60/3 31 40 40
575/60/3 24 35 35
Machine and steam built-in booster
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 25 35 35
240/60/3 22 30 30
480/60/3 12 15 15
575/60/3 9 15 15
70°F/39°C Rise – 22 kW
Machine and Electric built-in booster
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 131 175 175
240/60/3 115 150 150
480/60/3 58 80 80
575/60/3 47 60 60
40°F/22°C Rise – 12 kW
Machine and Electric built-in booster
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 104 150 150
240/60/3 91 125 125
480/60/3 46 60 60
575/60/3 37 50 50
Machine Only
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 74 100 100
240/60/3 65 90 90
480/60/3 33 45 45
575/60/3 25 35 35
Machine and steam built-in booster
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 29 40 40
240/60/3 26 35 35
480/60/3 12 15 15
575/60/3 10 15 15
70°F/39°C Rise – 22 kW
Machine and Electric built-in booster
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 136 175 175
240/60/3 118 150 150
480/60/3 60 80 80
575/60/3 47 60 60
40°F/22°C Rise – 12 kW
Machine and Electric built-in booster
Elec.
Specs.
Rated
Amps
Minimum
Supply Ckt.
Conductor
Ampacity
Maximum
Overcurrent
Protective
Device
208/60/3 108 150 150
240/60/3 94 125 125
480/60/3 47 60 60
575/60/3 37 50 50
76 DRPW, 80 DRFFPW, 90 DRHDPW
TABLE A - Machine Connection
76 DRPW, 80 DRFFPW, 90 DRHDPW
TABLE B - Machine & Booster Connection
Contaqct factory for single phase information.
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
2674 N. Service Road, Jordan Station, Ontario, Canada L0R 1S0 • 905/562-4195 • Fax: 905/562-4618
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
‘USGBC’ and related logo is a trademark owned by the U.S. Green Building Council and is used by permission.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
2674 N. Service Road, Jordan Station, Ontario, Canada L0R 1S0 • 905/562-4195 • Fax: 905/562-4618
54 DR SERIES RACK CONVEYOR
Cantilever
Sideloader
(No hood)
Model RCT 64
or RCT 84
Roller
Conveyor Table
OPTIONS & ACCESSORIES
: Tank heat: choice of steam coil, steam injector, hot water coil
: 2 Hp prewash motor
: 48" Blower-dryer - steam or electric
: Booster Heaters (completely interplumbed, controls
are interwired)
: Steam: 40°F or 70°F rise
: Electric: 12 kW (40°F rise) (built-in only)
: Electric: 22 kW (70°F rise) (built-in only)
Cantilever sideloader (with or without hood) for 90° load operation
: 24" Sideload
: 30" Sideload (accepts sheet pans)
: Extended pawl bar (extended drive unit) for use with
load tabling
: Racks: peg or flat racks (specify type)
: Steam pressure regulating valve (unmounted)
: Table limit switch, unmounted (recommended on all
rack conveyor installations)
: Vent cowl, stainless steel with 7" stack and locking damper
: Extended vent hood, stainless steel with 7" stack and
locking damper
: Water pressure regulating valve (unmounted)
(standard with booster)
: Two-point electrical connection
: Water hammer kit
: Drain tempering kit
: Vertical clearance through machine: 24"
(instead of standard 20") for larger ware
: Model CCT 180 (180° Corner Conveyor Table)
: Model CCT 90 (90° Corner Conveyor Table)
: Model RCT 64 or RCT 84 Roller Conveyor Table
(See factory for custom length)
NEW CCT 90
90° Corner Conveyor Table (shown)
NEW CCT 180
180° Corner Conveyor Table
also available
High-Temperature
Rack Conveyor Dishwashing Machine with
Dual Stage Rinse
54 DR SERIES
54 DR, 76 DRPW, 80 DRFFPW, 90 DRHDPW
/
