(2M) 8/09 Printed in U.S.A.
CH048
Pot, Pan, Utensil
Door Type
Washing Machine
PP28
PP28 POT, PAN, UTENSIL WASHER
STANDARD FEATURES
• Balanced door system
• Detergent/chemical connection provisions
• Door safety switch on each door
• Enclosure panels (front and sides)
• External lift-out refuse basket
• Fully automatic wash and rinse cycle
• Hold-down grid
• 7.5-Hp drip-proof pump motor
• Interchangeable upper and lower wash and rinse arms
• Low water tank heat protection
• Recessed, front-mounted controls
• Six-inch diameter vent connection
• Electric wash tank heat
SPECIFIER STATEMENT
Specified unit will be Champion model PP-28 pot, pan,
utensil door type washing machine.
Features adjustable wash cycle depending on solid wares from
2 to 5 minutes, revolving upper and lower high pressure spray
arms, large wash chamber spacious enough to accommodate
140 quart mixing bowls, fully automatic operation, and made
entirely of heavy gauge stainless steel from the base to spray
arms. One year parts and labor warranty.
Project______________________________________________
Item No._____________________________________________
Quantity_____________________________________________
Champion Industries, Inc.
P. O. Box 4149, Winston-Salem, NC 27115
Tel: 336/661-1556 Fax: 336/661-1979
www.championindustries.com
OPTIONS & ACCESSORIES
Corner Operation
Straight-through Operation
Front-loading Operation
Ten-inch Shelf on front-loading machine
Steam Coil tank heat
Steam Injector tank heat
Boosters, Stainless Steel (completely interplumbed,
controls are interwired)
Steam: 40°F-70°F Rise (built-in) (externally mounted
with cover for corner model)
Electric: 40°F Rise (built-in) (externally mounted
with cover for corner model)
Electric: 70°F Rise (externally mounted with cover)
Exhaust Fan, 1/3 Hp
Racks, Stainless Steel (5" x 28" x 28")
NOTE: ALL electric boosters require separate electrical connection.
Electric Steam Electric Heat Steam Heat
Voltage
Heat Heat & Exhaust Fan & Exhaust Fan
208/60/3 50 22 53 25
240/60/3 45 21 48 24
480/60/3 22 11 24 13
Pot, Pan, Utensil
Door Type
Washing Machine
PP28
Volume crated: 111 cu. ft.
Shipping weight crated: 1100 lbs.
Shipping weight crated
with built-in booster: 1200 lbs.
Details, Dimensions & Connections
Warning: Plumbing and electrical connections should be made by qualified
workmen who will observe all the applicable plumbing, sanitary, safety codes
and the National Electrical Code.
Plumbing Notes: Because of the variation in house-supplied steam and
water pressures, steam and water pressure regulating valves (PRVs) are needed
(water PRV is standard on model with built-in booster). The PRVs can either be
purchased from Champion or obtained locally.
Note: Water Hammer Arrestor (meeting ASSE-1010 standard or equivalent)
to be supplied (by others) in common water supply line at service connection.
10"
2A
2A
1A
3A 6A 5A
4
5A
6A
4
1A
3A
2A
1A
3A
2B
6B
3B
5
4
5A
6A
6A
6A
4
1A3A
2A
1A
3A
1B
2B
4
4
1B
2B
1A3A
Steam BoosterElectric or Steam Heat
Front Loading
Operation
Corner
Operation
Plan ViewPlan View Plan View
18"
16"
42"
37"
42"
37"
2-1/2"
21-1/2"
30-3/8"
34"
34"
15"
15"
11-1/4"
11-1/4"
3-1/4"
24"
28-1/2"
3-1/4"
4-1/4"
7-3/4"
2-3/4"
24"
28-1/2"
4-1/2" 4-1/2"
1"
1"
73"
34"
Table
Height
Connection
34"
Table
Height
Connection
2-1/2"
12-1/2"
9-1/2"
9-1/2"
8-3/4"
3"
4"
35-3/4"
9-3/4"
24-1/4"
12-1/2"
8-1/2"
8"
6"
24-1/4"
12-1/2"
4-1/2"
1"
73"
1"
2"
28-7/8"
1-1/2" Roll
36"
34"
Table
Height
Connection
12"
Plumbing
Clearance
106"
Doors
Removal
95"
Doors
Up
28-7/8" Opening
28-1/2" Inside Track
28-3/8"
Inside Track
Booster
Consult Factory
for Clearance
* With built-in booster, allow
approximately 24" clearance
for ease of use.
Wall
Wall
28-3/8"
Inside Track
28"
Clearance
Through
Machine
19"
17"
24-1/4"
12-1/2"
22-1/2"
10-1/2"
35-3/4"
42"
37"
25-1/4"
34"
15"
11-1/4"
3-1/4"
4-3/4"
6" Min.
6" Min.
6" Min.
6" Min.
4-3/4"
24"
28-1/2"
9-1/2"
4-5/8"
3"
4"
5"
4"
35-3/4"
Front View Front View
Front View Side View
Electric Booster
Machine Load Amps
Front Loading
Operation
Electric or Steam Heat
Typical Table Construction
Plan View
Front View Side View
Corner Operation
Dimensions shown in inches
Utilities
1 Electrical
A See box (1) for machine connection.
B See box (2) for separate built-in 27 kW electric booster connection.
2 Hot Water
A 1" NPT 180°F connection. Flow pressure 20-22 psi/82.5 gph.
B 1" NPT 140°F connection. Flow pressure 20-22 psi/82.5 gph.
Unmounted water PRV provided.
3 Drain
A 1-1/2" NPT connection. Maximum flow 15 gpm.
B 3/4" NPT steam booster relief to open drain.
4 Vent
6" diameter. 200 cfm. (Contact the factory for optional
exhaust fan connections.)
5 Steam
A 3/4" NPT connection. Flow pressure 15-30 psi.
B 1-1/4" NPT connection (steam heat, steam booster).
6 Condensate
A 1/2" NPT machine connection return to boiler
(steam coil heat only).
B 3/4" NPT machine connection return to boiler
(steam heat, steam booster).
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
Pot, Pan, Utensil
Door Type
Washing Machine
PP28
SPECIFICATIONS
Machine Capacities
Racks per hr. (NSF rated) 25
Wash tank (gal.) 24
Motor Horsepower
Wash 7.5
Pump Capacity (gpm) 280
Wash Nozzle Pressure
(ft. head water) 50
Water Consumption
Gal. per hr. (max. use) 82
Gal. per rack 3.3
Temperatures °F
Wash 150
Rinse 180
Heating
Tank heat, electric (kW) 10
Tank heat, steam
(lbs./hr. at 15 psi flow pressure) 50
Electric booster (Kw required for 40°F rise) 27
Electric booster (kW required for 70°F rise) 45
Steam booster (lbs./hr. required for 40°F rise) 50
Steam booster (lbs./hr. required for 70°F rise) 85
Time Cycle
Wash – adjustable (minutes) 2-5
Rinse (seconds) 16
NOTE: For 70°F rise booster
connections and load amps,
contact factory. For corner model
booster connections and load
amps, contact factory.
For booster connections
contact factory.
10"
2A
2A
1A
3A 6A 5A
4
5A
6A
4
1A
3A
2A
1A
3A
2B
6B
3B
5
4
5A
6A
6A
6A
4
1A3A
2A
1A
3A
1B
2B
4
4
1B
2B
1A3A
Steam BoosterElectric or Steam Heat
Front Loading
Operation
Corner
Operation
Plan ViewPlan View Plan View
18"
16"
42"
37"
42"
37"
2-1/2"
21-1/2"
30-3/8"
34"
34"
15"
15"
11-1/4"
11-1/4"
3-1/4"
24"
28-1/2"
3-1/4"
4-1/4"
7-3/4"
2-3/4"
24"
28-1/2"
4-1/2" 4-1/2"
1"
1"
73"
34"
Table
Height
Connection
34"
Table
Height
Connection
2-1/2"
12-1/2"
9-1/2"
9-1/2"
8-3/4"
3"
4"
35-3/4"
9-3/4"
24-1/4"
12-1/2"
8-1/2"
8"
6"
24-1/4"
12-1/2"
4-1/2"
1"
73"
1"
2"
28-7/8"
1-1/2" Roll
36"
34"
Table
Height
Connection
12"
Plumbing
Clearance
106"
Doors
Removal
95"
Doors
Up
28-7/8" Opening
28-1/2" Inside Track
28-3/8"
Inside Track
Booster
Consult Factory
for Clearance
* With built-in booster, allow
approximately 24" clearance
for ease of use.
Wall
Wall
28-3/8"
Inside Track
28"
Clearance
Through
Machine
19"
17"
24-1/4"
12-1/2"
22-1/2"
10-1/2"
35-3/4"
42"
37"
25-1/4"
34"
15"
11-1/4"
3-1/4"
4-3/4"
6" Min.
6" Min.
6" Min.
6" Min.
4-3/4"
24"
28-1/2"
9-1/2"
4-5/8"
3"
4"
5"
4"
35-3/4"
Front View Front View
Front View Side View
Electric Booster
Load Amps Electric Booster
(27 kW) (When specified)
Front View Front View
Steam Booster
Plan View Plan View
Electric Booster
Dimensions shown in inches
Voltage PP-28
208/60/3 75
240/60/3 65
480/60/3 34
Pot, Pan, Utensil
Door Type
Washing Machine
PP28
PP28 POT, PAN, UTENSIL WASHER
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: 336/661-1979 • www.championindustries.com
Basket Rack
Utility Rack
Bake Sheet Rack
Pan Rack
ACCESSORIES
Rack Basket P/N 109584
(utensils and loose items)
Rack Pan P/N 109585
(baking pans)
Rack Bake Sheet P/N 109587
(baking sheets)
Rack Utility P/N 109586
(large pots and pans)
-
1
-
2
-
3
-
4
