Trendnet TEW-657BRM Quick Installation Guide

Brand: Trendnet

Model: TEW-657BRM

Category: WLAN access points

Type: Quick Installation Guide

TEW-657BRM

1.01

Quick Installation Guide

English 1

1. Before You Start

2. Hardware Installation 3

3. Configure The Modem 4

4. Setting up Encryption 7

Troubleshooting 9

Wireless Tips 11

Table of Contents

Version 10.23.2009

1. Before You Start

?A computer with a wired or wireless network adapter properly installed.

?Web Browser: Internet Explorer (5.0 or above)

A working ADSL Internet Connection

Package Contents

?CD-ROM (User’s Guide)

?Multi-Language Quick Installation Guide

?1 x RJ-45 Ethernet Cable

?1 x RJ-11 Telephone Cable

?Power Adapter (12V DC, 1A)

TEW-657BRM

System Requirements

During the installation of your Wireless ADSL Modem Router, the Setup Wizard will

automatically detect your ISP connection type. If the router cannot detect your ISP

connection type, you can manually specify the connection type. Please verify your DSL

Internet broadband connection type with your ISP and ensure you have all the

information for one of the following connection types:

A. Dynamic IP connection

ADSL Modem parameters (VPI or VCI), if it cannot be detected automatically.

ISP may require you to use a particular Hostname or Domain name.

B. Static or Fixed IP connection

Internet IP Address:_____. _____._____._____ (e.g. 215.24.24.129)

Subnet Mask: _____. _____._____._____

Gateway IP Address: ____. _____._____._____

Primary DNS:_____. _____._____._____

Secondary:_____. _____._____._____

ADSL Modem Parameters (VPI or VCI), if it cannot be detected

automatically.

C. PPPoE or PPPoA Dynamic IP connection

Password: ________________

ADSL Modem Parameters (VPI or VCI), if it cannot be detected

automatically.

D. IPoA Static or Fixed (IP over ATM) connection

Internet IP Address:_____. _____._____._____ (e.g. 215.24.24.129)

Subnet Mask: _____. _____._____._____

Gateway IP Address: ____. _____._____._____

Primary DNS:_____. _____._____._____

Secondary:_____. _____._____._____.

ADSL Modem Parameters (VPI or VCI), if it cannot be detected

automatically.

Collect Internet Service Provider (ISP) Information

ADSL

Terminator

To PCs

Power

LAN1

LAN2

LAN3

LAN4

ADSL

2. Hardware Installation

3. Connect the AC Power Adapter to the TEW-

657BRM and then to a power outlet.

1. Connect one end of the RJ-45 cable to one of

the TEW-657BRM's LAN ports. Connect the

other end of cable to the computer's Ethernet

port.

2. Connect one end of the RJ-11 cable to the

TEW-657BRM's ADSL port. Connect the other

end of the cable to the phone jack.

4. Verify that the following panel lights are on:

Power, LAN and Wireless.

3. Configure the Modem

Note: It is recommended that you configure the Modem from a wired computer.

1. Open your web browser, type

http://192.168.10.1 in the Address bar, and

then press Enter.

2. Enter the User Name and

password and then click OK. By default:

User name: admin

Password: admin

Note: User name and Password is case

sensitive.

3. Click Setup Wizard.

Note:

1. The example below is for Auto-detect. If the Setup Wizard could not automatically

detect your Internet connection, select Manual Selection and input the information

using the information provided by your ISP.

2. In the example below, the ADSL connection is PPPoE

4. Click Next.

5. Select Auto-detect and then click Next.

6. Configure the settings based on information

provided by your ISP. Then click Next.

7. Configure the settings based on information

provided by your ISP. Then click Next.

Note: For other connection methods, follow the on screen instructions after you select

auto-detect.

8. Please wait while the TEW-657BRM reboots.

9. Check the LEDs and then click OK.

10. Check Test Internet Connection, and then

click Finish.

11. Verify that the test has completed successfully.

Check that the ADSL and Internet LEDs are lit.

Then click Close.

12. Open up your browser and enter in a URL

(e.g. www.trendnet.com) to verify that you

have Internet connection.

4. Setting up Encryption

1. Click Wireless

Note: To protect your network from any unauthorized access it is recommended to

enable wireless encryption.

2. Select the Region, enter the desired SSID and

then click Save.

3. Click Configure SSID1 to set up Wireless

Security.

Your Configuration is complete

To ensure the highest level of customer service and support, please take a moment to

Thank you for choosing TRENDnet

For detailed information regarding the TEW-657BRM’s configuration and advanced settings,

please refer to the Troubleshooting section, User's Guide CD-ROM, or TRENDnet's website

at http://www.trendnet.com.

4. This example below is WPA2-PSK. Select a

Security System and enter an encryption key

in the PSK field. Keep the Encryption value

as AES, click Save and then click Close. For

WPA-PSK or WPA2-PSK, the Pre-Shared Key

must be between 8 and 63 ASCII or 64 HEX

characters. Make sure to copy down the

encryption key.

I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error message says

“The page cannot be displayed.” How can I get into the TEW-567BRM's web configuration

page?

heck your hardware settings again by following the instructions in Section 2.

2. Make sure the Power, LAN and WLAN lights are lit.

3. Make sure your TCP/IP settings are set to Obtain an IP address automatically

(see the steps below).

1. C

4. Reset the TEW-657BRM. To reset the TEW-657BRM, take a pin or paperclip and press

the reset button on the back of the Wireless Modem for 15 seconds. Then let go.

Troubleshooting

Windows Vista

Windows XP/2000

1. Go into the Control Panel, click Network and

Internet, click Network and Sharing Center,

click Manage Network Connections and

then right-click the Local Area Connection

icon and then click Properties.

2. Click Internet Protocol Version 4 (TCP/IPv4)

and then click Properties. Then click on

Obtain an IP address automatically.

1. Go into the Control Panel, double-click the

Network Connections icon and then right-

click the Local Area Connection icon and

then click Properties.

2. Click Internet Protocol (TCP/IP) and then

click Properties. Then click on Obtain an IP

address automatically.

The Modem does not auto-detect my DSL connection. What should I do?

Verify that your DSL account is activated.

2. Make sure all the cables are properly connected (see Section 2).

3. In Section 3, select manual selection in the Setup Wizard and configure the Modem based

on information provided by your ISP.

All the settings are correct, but I cannot make a wireless connection to the Modem. What

should I do?

1. Double check that the Wireless LED on the Modem is lit.

2. Power cycle the Modem. Unplug the power to the Modem. Wait 15 seconds, then plug

the power back in.

3. Contact the manufacturer of your wireless network adapter. Make sure the

wireless network adapter is configured with the proper SSID. The default SSID

of the TEW-657BRM is TRENDnet657. If you have enabled any encryption on

the Access Point, make sure to configure the wireless network adapter with the

same encryption key.

I forgot my login password. What should I do?

Take a pin or paperclip and press the reset button on the back of the Wireless Modem for 15

seconds. Then let go. This will return all settings to factory default. The default user name

and password is admin.

If you still encounter problems or have any questions regarding the TEW-657BRM, please contact

TRENDnet's Technical Support Department.

Page is loading ...

The following are some general wireless tips to help minimize the impact of interference within an

environment.

Assign your network a unique SSID

Do not use anything that would be identifying like “Smith Family Network”. Choose

something that you would easily identify when searching for available wireless networks.

Do not turn off the SSID broadcast

The SSID broadcast is intended to be on and turning it off can cause connectivity issues.

The preferred method of securing a wireless network is to choose a strong form of encryption

with a strong and varied encryption key.

Change the channel

Most wireless access points and routers are defaulted to channel 6. If you have a site survey

tool that will display the channels you can plan your channel selection around neighboring

access points to minimize interference from them. If your site survey tool does not display

the channel try using channels 1 or 11.

Change the channel bandwidth

If you are using an 802.11n router or access point you can also make the following changes.

Change the channel bandwidth to 20/40MHz. This will provide the highest possible

performance using an 802.11n device. Also, if using 802.11n you should be securing the

network with WPA2 security.

Avoid stacking hardware on top of each other to prevent overheating issues

Maintain enough free space around the hardware for good ventilation and airflow. There

should also be plenty of free space around the antennas to allow the wireless signal to

propagate. Please also make sure that the wireless hardware is not placed in any type of

shelving or enclosures.

There are a number of other environmental factors that can impact the range of wireless

devices.

1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at

an angle. The more material the signal has to pass through the more signal you will lose.

Note: after setting up the SSID, encryption type and encryption key/passphrase, please

make a note of them for future reference. You will need this information to connect your

wireless computers to the wireless router/access point.

Note: Due to Wi-Fi certification considerations if you choose WEP, WPA or WPA2-TKIP

encryption this device may operate in legacy wireless mode (802.11b/g). You may not get

802.11n performance as these forms of encryption are not supported by the 802.11n

specification.

Wireless Tips

2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of

a wireless device. Position the wireless devices in a manner that will minimize the amount

of obstructions between them.

3. Building materials can have a large impact on your wireless signal. In an indoor

environment, try to position the wireless devices so that the signal passes through less

dense material such as dry wall. Dense materials like metal, solid wood, glass or even

furniture may block or degrade the signal.

4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless

adapter's site survey tool to determine the best antenna orientation for your wireless

devices.

5. Interference from devices that produce RF (radio frequency) noise can also impact your

signal. Position your wireless devices away from anything that generates RF noise, such

as microwaves, HAM radios, Walkie-Talkies and baby monitors.

6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as

2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency

can potentially drop the wireless signal. Although the phone may not be in use, the base

can still transmit wireless signals. Move the phone's base station as far away as possible

from your wireless devices.

If you are still experiencing low or no signal consider repositioning the wireless devices or installing

additional access points. The use of higher gain antennas may also provide the necessary

coverage depending on the environment.

GPL/LGPL General Information

This TRENDnet product includes free software written by third party developers. These codes are subject to the GNU

General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). These codes are distributed WITHOUT

WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these

codes. The details of the GNU GPL and LGPL are included in the product CD-ROM.

Please also go to (http://www.gnu.org/licenses/gpl.txt) or (http://www.gnu.org/licenses/lgpl.txt) for specific terms of each

license.

The source codes are available for download from TRENDnet's web site (http://trendnet.com/downloads/list_gpl.asp) for at

least three years from the product shipping date.

You could also request the source codes by contacting TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

Informations générales GPL/LGPL

Ce produit TRENDnet comprend un logiciel libre écrit par des programmeurs tiers. Ces codes sont sujet à la GNU General

Public License ("GPL" Licence publique générale GNU) ou à la GNU Lesser General Public License ("LGPL" Licence

publique générale limitée GNU). Ces codes sont distribués SANS GARANTIE et sont sujets aux droits d'auteurs des

programmeurs. TRENDnet ne fournit pas d'assistance technique pour ces codes. Les détails concernant les GPL et LGPL

GNU sont repris sur le CD-ROM du produit.

Veuillez également vous rendre en (http://www.gnu.org/licenses/gpl.txt) ou en (http://www.gnu.org/licenses/lgpl.txt) pour les

conditions spécifiques de chaque licence.

Les codes source sont disponibles au téléchargement sur le site Internet de TRENDnet web site

(http://trendnet.com/downloads/list_gpl.asp) durant au moins 3 ans à partir de la date d'expédition du produit.

Vous pouvez également demander les codes source en contactant TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

Allgemeine Informationen zu GPL/LGPL

Linux Version 2.4.0-test 3 v. 10.07.2000 (http://www.kernel.org/pub/linux/kernel/v2.4/old-test-kernels/linux-2.4.0-test3.tar.bz2),

sowie weitere freie Software. Sie haben durch den Erwerb dieses Produktes keinerlei Gewährleistungsansprüche gegen die

Berechtigten an der oben genannten Software erworben; weil diese die Software kostenfrei lizenzieren gewähren sie keine

Haftung gemäß unten abgedruckten Lizenzbedingungen. Die Software darf von jedermann im Quell-und Objektcode unter

Beachtung der Lizenzbedingungen der GNU General Public License Version 2, und GNU Lesser General Public License

(LGPL) vervielfältigt, verbreitet und verarbeitet werden. Die Lizenz ist unten im englischsprachigen Originalwortlaut

wiedergegeben. Eine nichtoffizielle Übersetzung in die deutsche Sprache finden Sie im Internet unter

(http://www.gnu.de/documents/gpl-2.0.de.html). Eine allgemeine öffentliche GNU Lizenz befindet sich auch auf der

mitgelieferten CD-ROM.

Sie können Quell-und Objektcode der Software für mindestens drei Jahre auf unserer Homepage www.trendnet.com im

Downloadbereich (http://trendnet.com/langen/downloads/list_gpl.asp) downloadend. Sofern Sie nicht über die Möglichkeit

des Downloads verfügen können Sie bei TRENDnet.

20675 Manhattan Place, Torrance, CA 90501 -U.S.A -, Tel.: +1-310-961-5500, Fax: +1-310-961-5511 die Software anfordern.

Información general sobre la GPL/LGPL

Este producto de TRENDnet incluye un programa gratuito desarrollado por terceros. Estos códigos están sujetos a la

Licencia pública general de GNU (“GPL”) o la Licencia pública general limitada de GNU (“LGPL”). Estos códigos son

distribuidos SIN GARANTÍA y están sujetos a las leyes de propiedad intelectual de sus desarrolladores. TRENDnet no ofrece

servicio técnico para estos códigos. Los detalles sobre las licencias GPL y LGPL de GNU se incluyen en el CD-ROM del

producto.

Consulte también el (http://www.gnu.org/licenses/gpl.txt) ó el (http://www.gnu.org/licenses/lgpl.txt) para ver las cláusulas

específicas de cada licencia.

Los códigos fuentes están disponibles para ser descargados del sitio Web de TRENDnet

(http://trendnet.com/downloads/list_gpl.asp) durante por lo menos tres años a partir de la fecha de envío del producto.

También puede solicitar el código fuente llamando a TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

Îáùàÿ èíôîðìàöèÿ î ëèöåíçèÿõ GPL/LGPL

Â ñîñòàâ äàííîãî ïðîäóêòà TRENDnet âõîäèò áåñïëàòíîå ïðîãðàììíîå îáåñïå÷åíèå, íàïèñàííîå ñòîðîííèìè

ðàçðàáîò÷èêàìè. Ýòî ÏÎ ðàñïðîñòðàíÿåòñÿ íà óñëîâèÿõ ëèöåíçèé GNU General Public License ("GPL") èëè GNU

Lesser General Public License ("LGPL"). Ïðîãðàììû ðàñïðîñòðàíÿþòñÿ ÁÅÇ ÃÀÐÀÍÒÈÈ è îõðàíÿþòñÿ àâòîðñêèìè

ïðàâàìè ðàçðàáîò÷èêîâ. TRENDnet íå îêàçûâàåò òåõíè÷åñêóþ ïîääåðæêó ýòîãî ïðîãðàììíîãî îáåñïå÷åíèÿ.

Ïîäðîáíîå îïèñàíèå ëèöåíçèé GNU GPL è LGPL ìîæíî íàéòè íà êîìïàêò-äèñêå, ïðèëàãàåìîì ê ïðîäóêòó.

Â ïóíêòàõ (http://www.gnu.org/licenses/gpl.txt) è (http://www.gnu.org/licenses/lgpl.txt) èçëîæåíû êîíêðåòíûå óñëîâèÿ

êàæäîé èç ëèöåíçèé.

Èñõîäíûé êîä ïðîãðàìì äîñòóïåí äëÿ çàãðóçêè ñ âåá-ñàéòà TRENDnet (http://trendnet.com/downloads/list_gpl.asp) â

òå÷åíèå, êàê ìèíèìóì, òðåõ ëåò ñî äíÿ ïîñòàâêè ïðîäóêòà.

Êðîìå òîãî, èñõîäíûé êîä ìîæíî çàïðîñèòü ïî àäðåñó TRENDnet.

20675 Manhattan Place, Torrance, CA 90501, USA. Tel: +1-310-961-5500 Fax: +1-310-961-5511

Page is loading ...

Trendnet TEW-657BRM Quick Installation Guide

Brand: Trendnet

Model: TEW-657BRM

Category: WLAN access points

Type: Quick Installation Guide

Download PDF

report

Trendnet TEW-657BRM Quick Installation Guide

Trendnet TEW-657BRM Quick Installation Guide

Related papers

Other documents