Lenovo ThinkSystem SR950 7X13 Setup Manual

ThinkSystem SR950

Setup Guide

Machine Types: 7X12, 7X11, and 7X13

Note

Before using this information and the product it supports, be sure to read and understand the safety

information and the safety instructions, which are available at:

http://thinksystem.lenovofiles.com/help/topic/safety_documentation/pdf_files.html

This equipment is not suitable for use in locations where children are likely to be present.

In addition, be sure that you are familiar with the terms and conditions of the Lenovo warranty for your server,

which can be found at:

http://datacentersupport.lenovo.com/warrantylookup

Second Edition (December 2017)

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services

Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.

GS-35F-05925

Contents

Chapter 1. Introduction . . . . . . . . . 1

Server package contents . . . . . . . . . . . . 1

Features. . . . . . . . . . . . . . . . . . . 1

Specifications . . . . . . . . . . . . . . . . 3

Management options. . . . . . . . . . . . . . 8

Chapter 2. Server components . . . . 15

Front view . . . . . . . . . . . . . . . . . 16

Front operator panel . . . . . . . . . . . 18

Rear view . . . . . . . . . . . . . . . . . 21

Internal cable routing. . . . . . . . . . . . . 24

Cable routing for common components . . . 26

Cable routing for drives . . . . . . . . . . 29

Parts list. . . . . . . . . . . . . . . . . . 39

Power cords . . . . . . . . . . . . . . 43

Chapter 3. Server hardware setup . . 45

Server setup checklist . . . . . . . . . . . . 45

Installation Guidelines . . . . . . . . . . . . 46

System reliability guidelines . . . . . . . . 47

Handling static-sensitive devices . . . . . . 47

Install server hardware options . . . . . . . . . 48

Remove the front cover . . . . . . . . . . 48

Install the compute system board . . . . . . 49

Install a processor-heat-sink module. . . . . 51

Install a memory module . . . . . . . . . 54

Install a hard disk drive backplane . . . . . . 57

Install a hard disk drive . . . . . . . . . . 62

Install the front cover . . . . . . . . . . . 65

Install an adapter . . . . . . . . . . . . 65

Install a riser . . . . . . . . . . . . . . 74

Install a power supply. . . . . . . . . . . 81

Install the server in a rack . . . . . . . . . . . 84

Cable the server . . . . . . . . . . . . . . 84

Power on the server (connect input power) . . . . 85

Validate server setup . . . . . . . . . . . . . 85

Power off the server (disconnect input power) . . . 85

Chapter 4. System configuration . . . 87

Set the network connection for the Lenovo XClarity

Controller . . . . . . . . . . . . . . . . . 87

Set front USB port for Lenovo XClarity Controller

connection. . . . . . . . . . . . . . . . . 87

Update the firmware . . . . . . . . . . . . . 88

Configure the firmware . . . . . . . . . . . . 91

Memory configuration . . . . . . . . . . . . 91

Independent memory mode . . . . . . . . 92

Memory mirroring . . . . . . . . . . . . 92

Memory sparing . . . . . . . . . . . . . 92

RAID configuration . . . . . . . . . . . . . 92

Install the operating system . . . . . . . . . . 93

Back up the server configuration . . . . . . . . 93

Chapter 5. Resolving installation

issues . . . . . . . . . . . . . . . . . 95

Appendix A. Getting help and

technical assistance . . . . . . . . . . 99

Before you call . . . . . . . . . . . . . . . 99

Collecting service data . . . . . . . . . . . . 100

Contacting Support . . . . . . . . . . . . . 101

Appendix B. Component

reference . . . . . . . . . . . . . . . . 103

Internal connectors . . . . . . . . . . . . . 103

System-board connectors . . . . . . . . . 103

Storage-board-assembly connectors . . . . 103

I/O-tray connectors . . . . . . . . . . . 104

Storage interposer connectors . . . . . . . 107

RAID card connectors . . . . . . . . . . 108

Drive backplane connectors . . . . . . . . 109

Component access . . . . . . . . . . . . . 110

Adapter replacement . . . . . . . . . . . 110

Compute tray (upper or lower)

replacement . . . . . . . . . . . . . . 123

Compute system board replacement. . . . . 126

Compute system board filler replacement . . . 129

Fan cage replacement . . . . . . . . . . 131

Front cover replacement . . . . . . . . . 139

Hard disk drive replacement . . . . . . . . 140

Hard disk drive backplane replacement. . . . 144

I/O tray replacement . . . . . . . . . . . 151

M.2 backplane replacement . . . . . . . . 154

M.2 drive replacement . . . . . . . . . . 158

Memory air baffle replacement . . . . . . . 161

Memory module replacement . . . . . . . 165

Riser replacement . . . . . . . . . . . . 169

Storage interposer replacement. . . . . . . 181

Storage tray replacement . . . . . . . . . 187

Index . . . . . . . . . . . . . . . . . . 191

ii ThinkSystem SR950 Setup Guide

Chapter 1. Introduction

The Lenovo ThinkSystem SR950 server is a high performance 4U rack server that supports up to eight Intel

Xeon processors. It is an enterprise-class server designed for customers requiring four or more processors,

large amounts of memory, and numerous I/O connections.

The server comes with a limited warranty. For details about the warranty, see:

https://datacentersupport.lenovo.com/documents/ht100742

For details about your specific warranty, see:

http://datacentersupport.lenovo.com/warrantylookup

Server package contents

When you receive your server, verify that the shipment contains everything that you expected to receive.

The server package includes the following items:

• Lenovo ThinkSystem SR950 server

• Rail installation kit (optional). Detailed instructions for installing the server in a rack using these rails are in

the Rack Installation Instructions document packaged with your server.

• Material box, including items such as the power cords, printed documentation, and an accessory kit.

If any item is missing or damaged, contact your place of purchase. Ensure that you retain your proof of

purchase and packing material. They might be required to receive warranty service.

Features

Performance, ease of use, reliability, and expansion capabilities were key considerations in the design of

your server. These design features make it possible for you to customize the system hardware to meet your

needs today and provide flexible expansion capabilities for the future.

Your server implements the following features and technologies:

• Lenovo XClarity Controller (XCC)

The Lenovo XClarity Controller is the common management controller for Lenovo ThinkSystem server

hardware. The Lenovo XClarity Controller consolidates multiple management functions in a single chip on

the server system board.

Some of the features that are unique to the Lenovo XClarity Controller are enhanced performance, higher-

resolution remote video, and expanded security options. For additional information about the Lenovo

XClarity Controller, see:

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.systems.management.xcc.doc/product_page.html

• UEFI-compliant server firmware

Lenovo ThinkSystem firmware is Unified Extensible Firmware Interface (UEFI) 2.5 compliant. UEFI

replaces BIOS and defines a standard interface between the operating system, platform firmware, and

external devices.

Lenovo ThinkSystem servers are capable of booting UEFI-compliant operating systems, BIOS-based

operating systems, and BIOS-based adapters as well as UEFI-compliant adapters.

Note: The server does not support DOS (Disk Operating System).

• Active Memory

The Active Memory feature improves the reliability of memory through memory mirroring. Memory

mirroring mode replicates and stores data on two pairs of DIMMs within two channels simultaneously. If a

failure occurs, the memory controller switches from the primary pair of memory DIMMs to the backup pair

of DIMMs.

• Large system-memory capacity

The server supports synchronous dynamic random-access memory (SDRAM) registered dual inline

memory modules (DIMMs) with error correcting code (ECC). For more information about the specific types

and maximum amount of memory, see “Specifications” on page 3.

• Integrated network support

The server comes with one of several types of LOM adapter, which supports connection to one of the

following network types: 10GBASE-T (2–port or 4–port), 1GBASE-T (2–port or 4–port), or 2x 10Gb SFP+

(2–port or 4–port). An ML2 form factor network adapter is also supported.

• Integrated Trusted Platform Module (TPM)

This integrated security chip performs cryptographic functions and stores private and public secure keys.

It provides the hardware support for the Trusted Computing Group (TCG) specification. You can

download the software to support the TCG specification when the software is available.

Note: For customers in the People's Republic of China, TPM is not supported. However, customers in the

People's Republic of China can install a Trusted Cryptographic Module (TCM) adapter (sometimes called

a daughter card).

• Large data-storage capacity and hot-swap capability

The server models support a maximum of 24 2.5-inch hard disk drives that are of the hot-swap Serial

Attached SCSI (SAS) or hot add/remove NVMe types (depending on system configuration).

With the hot-swap feature, you can add, remove, or replace hard disk drives without turning off the server.

• Light path diagnostics

Light path diagnostics provides LEDs to help you diagnose problems and an LCD information display

panel that provides additional diagnostic information. For more information about the light path

diagnostics, see Light path diagnostics panel and Light path diagnostics LEDs.

• Mobile access to Lenovo Service Information website

The server provides a QR code on each system board that you can scan using a QR code reader and

scanner with a mobile device to get quick access to the Lenovo Service Information website. The Lenovo

Service Information website provides additional information for parts installation, replacement videos, and

error codes for server support. See “QR code” on page 15 for information about accessing the QR code

label.

• Active Energy Manager

2

ThinkSystem SR950 Setup Guide

Lenovo XClarity Energy Manager is a power and temperature management solution for data centers. You

can monitor and manage the power consumption and temperature of Converged, NeXtScale, System x,

and ThinkServer servers, and improve energy efficiency using Lenovo XClarity Energy Manager.

• Redundant networking connection

The Lenovo XClarity Controller provides failover capability to a redundant Ethernet connection with the

applicable application installed. If a problem occurs with the primary Ethernet connection, all Ethernet

traffic that is associated with the primary connection is automatically switched to the optional redundant

Ethernet connection. If the applicable device drivers are installed, this switching occurs without data loss

and without user intervention.

• Redundant cooling and optional power capabilities

The server supports a maximum of four 1100-watt (110V or 220V ac) or 1600-watt (220V ac) hot-swap

power supplies and six or twelve hot-swap fans, depending on the server configuration. The redundant

cooling by the fans in the server enables continued operation if a fan fails.

Note: You cannot mix power supply types in the server.

• ThinkSystem RAID support

The ThinkSystem RAID adapter provides hardware redundant array of independent disks (RAID) support

to create configurations. The standard RAID adapter provides RAID levels 0 and 1. An optional RAID

adapter is available for purchase.

Specifications

The following information is a summary of the features and specifications of the server. Depending on the

model, some features might not be available, or some specifications might not apply.

Table 1. Server Specifications

Specification

Description

Size

4U server

• Height: 175.8 mm (6.9 in.)

• Depth:

– EIA flange to rear: 800.0 mm (31.5 in.)

– Overall: 853.0 mm (33.6 in.)

• Width:

– Top cover: 447.0 mm (17.6 in.)

– EIA flange: 483.0 mm (19.0 in.)

Weight Approximately 32.6 kg (71.9 lbs.) to 58.7 kg (129.4 lbs.) depending on your

configuration.

Processor (depending on the

model)

Supports multi-core Intel Xeon processors, with integrated memory controller and

Ultra Path Interconnect (UPI)

• Two processors, minimum (expandable up to eight).

• Designed for the LGA 3647-0 socket

• Scalable up to 224 cores (with eight processors installed)

For a list of supported processors, see

http://www.lenovo.com/us/en/serverproven/

and the “Processor Options” section of the Lenovo ThinkSystem SR950 Product Guide

at http://lenovopress.com/LP0647

.

Chapter 1. Introduction 3

Table 1. Server Specifications (continued)

Specification

Description

Memory

• Minimum: 32 GB

• Maximum: 12 TB

– 3.1 TB using registered DIMMs (RDIMMs)

– 6.2 TB using load reduction DIMMs (LRDIMMs)

– 12.4 TB using three-dimensional-stacking registered DIMMs (3DS RDIMMs)

• Type:

– PC4-21300 (DDR4-2666), operating speed depends on processor model and

UEFI settings

– Single-rank or dual-rank

– Registered DIMM (RDIMM), load reduced DIMM (LRDIMM), or three-

dimensional-stacking registered DIMM (3DS RDIMM)

• Slots: 24 dual inline in each compute tray (96 DIMMs, maximum)

• Supports (depending on the model):

– 16 GB, 32 GB RDIMMs

– 64 GB LRDIMMs

– 128 GB 3DS RDIMMs

Drive expansion

• Up to six SAS/SATA/NVMe drive backplanes:

• Up to 24 2.5-inch hot-swap drive bays:

– Up to 24 SATA/SAS drives (dependent on installed drive backplanes)

– Up to 12 NVMe drives (dependent on installed drive backplanes)

4 ThinkSystem SR950 Setup Guide

Table 1. Server Specifications (continued)

Specification

Description

Expansion slots

Up to seventeen expansion slots (dependent on server configuration):

• Slot 1 - 4: PCI Express 3.0 for PCIe riser-card with the following slots available

depending on the riser card installed:

1. x8/x8/x8/x8 PCIe full-height riser kit provides:

– Slot 1: PCI Express 3.0 x8

– Slot 2: PCI Express 3.0 x8

– Slot 3: PCI Express 3.0 x8

– Slot 4: PCI Express 3.0 x8

2. x16/x16 PCIe full-height riser kit provides:

– Slot 3: PCI Express 3.0 x16

– Slot 4: PCI Express 3.0 x16

3. x16/x16/x16/x16 PCIe full-height riser kit (8–processor systems only)

provides:

– Slot 1: PCI Express 3.0 x16

– Slot 2: PCI Express 3.0 x16

– Slot 3: PCI Express 3.0 x16

– Slot 4: PCI Express 3.0 x16

• Slot 5: PCI Express 3.0 x16 (low profile)

• Slot 6: PCI Express 3.0 x16 (low profile)

• Slot 7: PCI Express 3.0 x8 (low profile)

• Slot 8: ML2 x16 network adapter (with NC-SI support)

• Slot 9: LOM adapter

• Slot 10 - 15: PCI Express 3.0 for PCIe riser-card with the following slots available

depending on the riser-card installed:

1. x8/x8/x8/x8 PCIe full-height riser kit provides:

– Slot 10: PCI Express 3.0 x8

– Slot 11: PCI Express 3.0 x8

– Slot 12: PCI Express 3.0 x8

– Slot 13: PCI Express 3.0 x8

2. x16/x16 PCIe full-height riser kit provides:

– Slot 12: PCI Express 3.0 x16

– Slot 13: PCI Express 3.0 x16

3. x16/x16/x16/x16 PCIe and ML2 x16 full-height riser kit (8–processor systems

only) provides:

– Slot 10: PCI Express 3.0 x16

– Slot 11: PCI Express 3.0 x16

– Slot 12: PCI Express 3.0 x16

– Slot 13: PCI Express 3.0 x16

– Slot 14: PCI Express 3.0 x16

– Slot 15: ML2 x16 network adapter (no NC-SI support)

• Slot 16 - 17: x8/x8 PCIe low-profile riser kit (processor-rich systems only)

provides:

Chapter 1. Introduction 5

Table 1. Server Specifications (continued)

Specification

Description

– Slot 16: PCI Express 3.0 x8

– Slot 17: PCI Express 3.0 x8

Integrated functions

• Lenovo XClarity Controller, which provides service processor control and

monitoring functions, video controller, and remote keyboard, video, mouse, and

remote drive capabilities.

• Light-path diagnostics

• Standard connectors (front of server):

– DB-15 VGA port

– USB 2.0 ports (two):

– USB 2.0 for Lenovo XClarity Controller management

– USB 2.0

• Standard connectors (rear of server):

– DB-15 VGA port

– DB-9 serial port

– RJ-45 system-management network port. This connector is dedicated for

Lenovo XClarity Controller functions and runs at 1 gigabit (Gb) speed.

– USB 3.0 ports (two)

RAID controller (depending on

the model)

The following RAID options are available for this server:

• ThinkSystem 430-8i Basic Hardware RAID PCIe Adapter (supports RAID levels 0/

1/10/5 cacheless)

• ThinkSystem 430-16i Basic Hardware RAID PCIe Adapter (supports RAID levels 0/

1/10/5 cacheless)

• ThinkSystem 530-8i Basic Hardware RAID PCIe Adapter (RAID levels 0/1/10/5

cacheless)

• ThinkSystem 730-8i Value Advanced Hardware RAID 1 GB Cache PCIe Adapter

(supports RAID levels 0/1/5/10)

• ThinkSystem RAID 930-8i Advanced Hardware 2 GB Flash Cache PCIe Adapter

(supports RAID levels 0/1/5/6/10/50/60)

• ThinkSystem RAID 930-16i Advanced Hardware 4 GB Flash Cache PCIe Adapter

(supports RAID levels 0/1/5/6/10/50/60)

Fans Up to twelve (60 mm x 38 mm) internal hot-swap system fans (dependent on server

configuration)

Notes:

• The six upper fans are not installed for the four-processor-limited server

configuration.

• Only three upper fans are installed for the storage-rich configuration.

Power supplies

• This server supports two types of hot-swap power supply units:

– 1100-watt power supply

– input voltage 110V or 220V ac

– 1600-watt power supply

– input voltage 220V ac

• The power subsystem supports balanced N+N redundancy operation, where N =

1 or 2.

6 ThinkSystem SR950 Setup Guide

Table 1. Server Specifications (continued)

Specification

Description

Acoustical noise emissions

(base configuration)

• Sound power, idling: 6.1 bels

• Sound power, operating: 6.1 bels

Note: The options supported in this server vary in function, power consumption, and

required cooling. Any increase in cooling required by these options will increase the

fan speed and generated sound level. The actual sound pressure levels measured in

your installation depend upon a variety of factors, including: the number of racks in

the installation; the size, materials, and configuration of the room; the noise levels of

other equipment; the room ambient temperature and barometric pressure; and the

location of employees in relation to the equipment.

Heat output Approximate heat output:

• Minimum configuration: 935 BTU, 275 W (in BTU per hour and watts)

– Minimum configuration of two microprocessors, two memory modules, one M.2

adapter, and no PCIe adapters.

• Maximum configuration: 21837 BTU, 6400 W (in BTU per hour and watts)

– Maximum configuration with four 1600–watt power supplies configured for

non-redundant operation under maximum loading.

Environment

• Air temperature:

– Server on: 5° to 45°C (41° to 113°F); altitude: 0 to 3050 m (10,006 ft) derate

maximum dry bulb temperature 1°C (33°F) per 125 m (410 ft) above 950 m

(3,117 ft). Maximum rate of change 20°C (68°F) per hour

– Server off: 5° to 45°C (41° to 113°F)

– Shipment: -40°C to 60°C (-40°F to 140°F)

• Humidity range (noncondensing):

– Server on: Minimum = higher (more moisture) of -12°C (10°F) dew point and 8%

to 90% relative humidity; maximum dew point: 24°C (75°F)

– Server off: 8% to 90% relative humidity; maximum dew point: 27°C (80°F)

– Shipment: 5% to 100%

Notes:

• Airborne particulates and reactive gases acting alone or in combination with other

environmental factors such as humidity or temperature might pose a risk to the

server. For information about the limits for particulates and gases, see

Particulate

contamination

.

• ASHRAE compliance information (see the “Operating Environment” section of

the

Lenovo ThinkSystem SR950 Product Guide at http://lenovopress.com/LP0647

for

specific ASHRAE compliance levels for each server configuration):

– The server is designed for thermal compliance in ASHRAE A4 ambient

environments. Certain processor and adapter configurations will limit product

environmental support to ASHRAE A2 ambient conditions.

– 205W processors used in an eight-socket configuration might experience a

slight drop in performance under extreme workloads when the ambient

temperature is above 30°C.

– NVMe devices are supported up to an ambient temperature of 35°C.

Chapter 1. Introduction 7

Management options

Several management interfaces are available for managing your server. The management options described

in this section are provided to support the direct management of Lenovo servers.

Function

Lenovo

XClarity

Administrator

Lenovo

XClarity

Integrator

Lenovo

XClarity

Energy

Manager

Lenovo

XClarity

Provisioning

Manager

Lenovo

XClarity

Essen-

tials

1

Lenovo

XClarity

Controller

Lenovo

Capacity

Planner

Lenovo

Business

Vantage

Multiple

systems

manage-

ment

√ √ √ √

Operating

system

deployment

√ √

Firmware

updates

2

√ √ √

3

√ √

System

configura-

tion

√ √ √ √ √

Events /

alerts

√ √ √ √

Inventory /

Log

√ √ √

4

√ √

Power

manage-

ment

√

5

√

Data center

planning

√

Security

manage-

ment

√

6

Notes:

1. Lenovo XClarity Essentials includes Lenovo XClarity Essentials OneCLI, Lenovo XClarity Essentials

Bootable Media Creator, and Lenovo XClarity Essentials UpdateXpress.

2. Most options can be updated through the Lenovo tools. Some options, such as GPU firmware or Omni-

Path firmware require the use of vendor tools.

3. Firmware updates are limited to Lenovo XClarity Provisioning Manager, Lenovo XClarity Controller

firmware, and UEFI updates only. Firmware updates for optional devices, such as adapters, are not

supported.

4. Limited inventory.

5. Power management function is supported by Lenovo XClarity Integrator for VMware vCenter.

6. Available only in the People’s Republic of China.

Lenovo XClarity Administrator

Lenovo XClarity Administrator is a centralized, resource-management solution that simplifies infrastructure

management, speeds responses, and enhances the availability of Lenovo server systems and solutions. It

8

ThinkSystem SR950 Setup Guide

runs as a virtual appliance that automates discovery, inventory, tracking, monitoring, and provisioning for

server, network, and storage hardware in a secure environment.

Lenovo XClarity Administrator provides a central interface to perform the following functions for all managed

endpoints:

• Manage and monitor hardware. Lenovo XClarity Administrator provides agent-free hardware

management. It can automatically discover manageable endpoints, including server, network, and storage

hardware. Inventory data is collected for managed endpoints for an at-a-glance view of the managed

hardware inventory and status.

• Configuration management. You can quickly provision and pre-provision all of your servers using a

consistent configuration. Configuration settings (such as local storage, I/O adapters, boot settings,

firmware, ports, and Lenovo XClarity Controller and UEFI settings) are saved as a server pattern that can

be applied to one or more managed servers. When the server patterns are updated, the changes are

automatically deployed to the applied servers.

• Firmware compliance and updates. Firmware management is simplified by assigning firmware-

compliance policies to managed endpoints. When you create and assign a compliance policy to managed

endpoints, Lenovo XClarity Administrator monitors changes to the inventory for those endpoints and flags

any endpoints that are out of compliance.

When an endpoint is out of compliance, you can use Lenovo XClarity Administrator to apply and activate

firmware updates for all devices in that endpoint from a repository of firmware updates that you manage.

• Operating System deployment. You can use Lenovo XClarity Administrator to manage a repository of

operating-system images and to deploy operating-system images to up to 28 managed servers

concurrently.

• Service and support. Lenovo XClarity Administrator can be set up to collect and send diagnostic files

automatically to your preferred service provider when certain serviceable events occur in Lenovo XClarity

Administrator and the managed endpoints. You can choose to send diagnostic files to Lenovo Support

using Call Home or to another service provider using SFTP. You can also manually collect diagnostic files,

open a problem record, and send diagnostic files to the Lenovo Support Center.

Lenovo XClarity Administrator can be integrated into external, higher-level management and automation

platforms through open REST application programming interfaces (APIs). Using the REST APIs, Lenovo

XClarity Administrator can easily integrate with your existing management infrastructure. In addition, you can

automate tasks using the PowerShell toolkit or the Python toolkit.

To obtain the latest version of the Lenovo XClarity Administrator, see:

https://datacentersupport.lenovo.com/documents/LNVO-LXCAUPD

Documentation for Lenovo XClarity Administrator is available at:

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxca.doc/aug_product_page.html

Lenovo XClarity Integrator

Lenovo also provides the following integrators that you can use to manage Lenovo servers from higher-level

management tools:

• Lenovo XClarity Integrator for VMware vCenter

• Lenovo XClarity Integrator Microsoft System Center

For more information about Lenovo XClarity Integrator, see:

http://www3.lenovo.com/us/en/data-center/software/systems-management/xclarity-integrators

Chapter 1. Introduction 9

Lenovo XClarity Energy Manager

Lenovo XClarity Energy Manager is a web-based power and temperature management solution designed for

data center administrators. It monitors and manages the power consumption and temperature of servers,

such as Converged, NeXtScale, System x, ThinkServer, and ThinkSystem servers, using the out-of-band

method. Lenovo XClarity Energy Manager models data center physical hierarchy and monitors power and

temperature at the server/group level. By analyzing monitored power and temperature data, Lenovo XClarity

Energy Manager greatly improves business continuity and energy efficiency.

With Lenovo XClarity Energy Manager, administrators can take control of power usage through improved

data analysis and lower the TCO (total cost of ownership). The tool optimizes data center efficiency by

allowing administrators to:

• Monitor energy consumption, estimate power need, and re-allocate power to servers as needed via IPMI

or Redfish.

• Track platform power consumption, inlet temperature, and component-level power consumption, such as

CPU and memory power consumption.

• Visually check the layout of room, row and rack via 2D thermal map.

• Show events and send e-mail or SNMP trap notifications when certain faults occur or certain thresholds

are reached.

• Limit the consumed amount of energy of an endpoint by setting up policies.

• Optimize energy efficiency by identifying hotspot or over-cooling servers to optimize cooling efficiency

and identifying low-usage servers to save energy.

• Reduce the power consumption to the minimum level to prolong service time during emergency power

event (such as a data-center power failure).

For more information about downloading, installation, and usage, see:

https://datacentersupport.lenovo.com/solutions/lnvo-lxem

Lenovo XClarity Provisioning Manager

Lenovo XClarity Provisioning Manager is embedded software that provides a graphic user interface (GUI) for

configuring the system with support for 10 languages. It simplifies the process of configuring Basic Input

Output System (BIOS) settings and configuring Redundant Array of Independent Disks (RAID) in an GUI

wizard. It also provides functions for updating applications and firmware, performing system diagnostics,

and automating the process of installing the supported Windows, Linux, or VMware ESXi operating systems

and associated device drivers.

Note: When you start a server and press F1, the Lenovo XClarity Provisioning Manager interface is displayed

by default. However, the text-based interface to system configuration (the Setup Utility) is also available.

From Lenovo XClarity Provisioning Manager, you can choose to restart the server and access the text-based

interface. In addition, you can choose to make the text-based interface the default interface that is displayed

when you press F1.

Lenovo XClarity Provisioning Manager provides a system summary of all installed devices and includes the

following functions:

• UEFI setup. Use this function to configure UEFI system settings, such as processor configuration, start

options, and user security. You can also view POST events and the System Event Log (SEL).

• Firmware update. Use this function to update the firmware for Lenovo XClarity Controller, Unified

Extensible Firmware Interface (UEFI), Lenovo XClarity Provisioning Manager, and operating system device

drivers.

10

ThinkSystem SR950 Setup Guide

• RAID setup. Use this function to configure RAID for the server. It provides an easy-to-use graphical

wizard that supports a unified process for performing RAID setup for a variety of RAID adapters. You can

also perform advanced RAID configuration from the UEFI Setup.

• OS installation. Use this function to deploy an operating system for the server with an easy-to-use

Guided Install mode. Operating systems can be installed using unattended mode after you choose the

Operating System version and basic settings; the device drivers are installed automatically.

A Manual Install mode is also available. You can export the drivers from system, manually install the

operating systems, and then install the drivers. This way, you do not need to go to the web to download

device drivers.

• Diagnostics. Use this function to view the overall health of devices installed in the server and to perform

diagnostics for hard disk drives and memory. You can also collect service data that can be saved to a

USB device and sent to Lenovo Support.

Note: The service data collected by Lenovo XClarity Provisioning Manager does not include the operating

system logs. To collect the operating system logs and the hardware service data, use Lenovo XClarity

Essentials OneCLI.

Documentation for Lenovo XClarity Provisioning Manager is available at:

http://sysmgt.lenovofiles.com/help/topic/LXPM/LXPM_introduction.html

Lenovo XClarity Essentials

Lenovo XClarity Essentials (LXCE) is a collection of server management utilities that provides a less

complicated method to enable customers to manage Lenovo ThinkSystem, System x, and Thinkserver

servers more efficiently and cost-effectively.

Lenovo XClarity Essentials includes the following utilities:

• Lenovo XClarity Essentials OneCLI is a collection of several command line applications, which can be

used to:

– Configure the server.

– Collect service data for the server. If you run Lenovo XClarity Essentials OneCLI from the server

operating system (in-band), you can collect operating system logs as well. You can also choose to view

the service data that has been collected or to send the service data to Lenovo Support.

– Update firmware and device drivers for the server. Lenovo XClarity Essentials OneCLI can help to

download UpdateXpress System Packs (UXSPs) for your server and update all the firmware and device

drivers payloads within the UXSP.

– Perform miscellaneous functions, such as rebooting the server or rebooting the BMC.

To learn more about Lenovo XClarity Essentials OneCLI, see:

https://datacentersupport.lenovo.com/documents/LNVO-CENTER

Documentation for Lenovo XClarity Essentials OneCLI is available at:

http://sysmgt.lenovofiles.com/help/topic/xclarity_essentials/overview.html

• Lenovo XClarity Essentials Bootable Media Creator (BoMC) is a software application that applies

UpdateXpress System Packs and individual updates to your system.

Using Lenovo XClarity Essentials Bootable Media Creator, you can:

– Update the server using an ISO image or CD.

– Update the server using a USB key.

– Update the server using the Preboot Execution Environment (PXE) interface.

– Update the server in unattendance mode.

Chapter 1. Introduction 11

– Update the server in Serial Over LAN (SOL) mode.

To learn more about Lenovo XClarity Essentials Bootable Media Creator, see:

https://datacentersupport.lenovo.com/solutions/lnvo-bomc

• Lenovo XClarity Essentials UpdateXpress is a software application that applies UpdateXpress System

Packs and individual updates to your system.

Using Lenovo XClarity Essentials UpdateXpress, you can:

– Update the local server.

– Update a remove server.

– Create a repository of updates.

To learn more about Lenovo XClarity Essentials UpdateXpress, see:

https://datacentersupport.lenovo.com/solutions/lnvo-xpress

Lenovo XClarity Controller

Lenovo XClarity Controller is the management processor for the server. It is the third generation of the

Integrated Management Module (IMM) service processor that consolidates the service processor

functionality, super I/O, video controller, and remote presence capabilities into a single chip on the server

system board.

There are two ways to access the management processor:

• Web-based interface. To access the web-based interface, point your browser to the IP address for the

management processor.

• Command-line interface. To access the CLI interface, use SSH or Telnet to log in to the management

processor.

Whenever power is applied to a server, the management processor is available. From the management

processor interface, you can perform the following functions:

• Monitor all hardware devices installed in the server.

• Power the server on and off.

• View the system event log and system audit log for the server.

• Use the Remote management function to log in to the server itself.

Documentation for Lenovo XClarity Controller is available at:

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.systems.management.xcc.doc/product_page.html

Lenovo Capacity Planner

Lenovo Capacity Planner is a power consumption evaluation tool that enhances data center planning by

enabling IT administrators and pre-sales to understand important parameters of different type of racks,

servers, and other devices. Lenovo Capacity Planner can dynamically calculate the power consumption,

current, British Thermal Unit (BTU), and volt-ampere (VA) rating at the rack level, and therefore improves the

efficiency of large scale deployments.

Lenovo Capacity Planner provides the following functions:

• Power and thermal evaluation in different deployments, including Flex System and High-Density servers,

chassis-level, and node-level customizable configuration.

• Customizable server configuration, selectable workload, CPU turbo model, and worst case of fans for

different evaluations in different user scenarios.

12

ThinkSystem SR950 Setup Guide

• Comprehensive and visual memory configuration guidance for best memory performance.

• Easy to download and run with popular web browsers, such as Internet Explorer 11, Firefox, Chrome, and

Edge.

Note: Users can also access the Lenovo website to run the tool online.

More information about Lenovo Capacity Planner is available at:

https://datacentersupport.lenovo.com/solutions/lnvo-lcp

Lenovo Business Vantage

Lenovo Business Vantage is a security software tool suite designed to work with the Trusted Cryptographic

Module (TCM) adapter for enhanced security, to keep user data safe, and to erase confidential data

completely from a hard disk drive.

Lenovo Business Vantage provides the following functions:

• Data Safe. Encrypt files to ensure data safety by using the TCM adapter.

• Sure Erase. Erase confidential data from a hard disk. This tool follows the industry standard method to do

the erasing and allows the user to select different erasing levels.

• Smart USB Protection. Prohibit unauthorized access to the USB port of devices.

• USB Data Safe. Encrypt files to ensure data security on a USB storage device.

Note: This tool is available in the People’s Republic of China only.

More information about Lenovo Business Vantage is available at:

http://support.lenovo.com.cn/lenovo/wsi/es/es.html

Chapter 1. Introduction 13

14 ThinkSystem SR950 Setup Guide

Chapter 2. Server components

Use the information in this section to learn about each of the components associated with your server.

Identifying your server

When you contact Lenovo for help, the machine type, model, and serial number information helps support

technicians to identify your server and provide faster service.

Figure 1 “Location of the ID label for the Lenovo ThinkSystem SR950” on page 15 shows the location of the

label containing the machine type, model, and serial number.

The model number, serial number, and a barcode of this server identification information are on the ID label

on the front of the server, as shown in the following illustration. You can also add other system information

labels to the front of the server in the customer label spaces (

1 in the following illustration).

Note: If any customer labels are placed on the removable front cover, make sure that the cover remains

installed on the same server where the labels were originally added.

Figure 1. Location of the ID label for the Lenovo ThinkSystem SR950

QR code

In addition, the service label that is located at the top rear of the compute system board inside the server,

provides a quick reference (QR) code for mobile access to service information. (You must disconnect all

server power cords before attempting to access the compute system board.) You can scan the QR code with

a mobile device using a QR code reader application and get quick access to the Service Information web

page (https://support.lenovo.com/p/servers/sr950). The Service Information web page provides additional

information for parts installation and replacement videos, and error codes for server support.

Figure 2. Service label and QR code

Network access label

The xClarity Controller (XCC) network access label is on the front of the server and must be removed before

operating the system. The label provides the default IPv4 host name and default IPv6 link local address of the

XCC.

Figure 3. Network access tag

Front view

The front view of the server varies slightly by the model. In some models, components are replaced by fillers.

16

ThinkSystem SR950 Setup Guide

Page is loading ...

Lenovo ThinkSystem SR950 7X13 Setup Manual

This manual is also suitable for

Lenovo ThinkSystem SR950 7X13 Setup Manual

Related papers

Other documents