Etac RELAX Operating instructions

RELAX
Etac
Brand
Etac
Model
RELAX
Type
Operating instructions

Etac RELAX is a backrest for shower seats, providing extra support and comfort during showering. It is easy to install, with strong adhesion when the glue area and fitting surface have a temperature of at least 20°C (68°F) and large pressure is applied. It takes 60 minutes for the glue to fully adhere, after which the backrest can withstand loads. RELAX is a valuable aid for individuals who need extra support and stability while showering, enhancing their safety and comfort.

Etac RELAX is a backrest for shower seats, providing extra support and comfort during showering. It is easy to install, with strong adhesion when the glue area and fitting surface have a temperature of at least 20°C (68°F) and large pressure is applied. It takes 60 minutes for the glue to fully adhere, after which the backrest can withstand loads. RELAX is a valuable aid for individuals who need extra support and stability while showering, enhancing their safety and comfort.

Monteringsanvisning/Assembly instructions/Montageanweisung/Montage-instructies
Etac Supply Center AB
Långgatan 12
SE-334 33 Anderstorp
www.etac.com
60°C
140°F
1a11939.3 2023-03-20
x1
Ryggstöd Relax duschsits
Backrest Relax shower seat
Rückenlehne für Duschklappsitz Relax
Rugleuning Relax douchezitting
8170 4060
1 2
3
4
5
Rengör underlaget där ryggstödet ska sitta från fett, damm,
smuts och fukt.
Clean off any grease, dust, dirt and moisture from the sur-
face where the backrest is to be tted.
Säubern Sie den Bereich, wo die Rückenlehne angebracht
werden soll, von Staub, Schmutz, Feuchtigkeit und Fett.
Verwijder vet, stof, vuil en vocht van het oppervlak waar de
rugleuning moet worden gemonteerd.
Optimal vidhäftning erhåller man när limytan resp.
underlaget har en temperatur av minst 20°C. Dessutom är
det viktigt att man använder hårt tryck vid appliceringen
Best adhesion is obtained when the glue area and the
tting surface have a temperature of at least 20°C. It is also
important to apply large pressure when tting the backrest.
Die beste Haftkraft erzielen Sie, wenn Klebeäche und das
zu befestigende Teil eine Mindesttemperatur von 20 °C
haben. Es ist des Weiteren wichtig, beim Anbringen der
Rückenlehne starken Druck auf die Klebeächen aus
zuüben.
Het te lijmen gebied en het montageoppervlak moeten voor
de beste hechting een temperatuur van minimaal 20 °C
hebben. Het is ook belangrijk om grote druk uit te oefenen
bij het monteren van de rugleuning.
Eftersom limmet behöver tid att fästa ordentligt i
underlaget, skall belastning av ryggstödet ske tidigast efter
60 minuter.
As the glue requires times to stick properly to the surface, it
is not permitted to put any loads on the backrest until
60 minutes have elapsed.
Der Kleber haftet erst nach einer gewissen Zeit voll an der
Oberäche, daher dürfen Sie die Rückenlehne erst nach
60 Minuten belasten.
De lijm heeft tijd nodig om aan het oppervlak te hechten;
daarom mag er pas 60 minuten na het aanbrengen van de
lijm belasting op de rugleuning worden geplaatst.
  • Page 1 1

Etac RELAX Operating instructions

RELAX
Etac
Brand
Etac
Model
RELAX
Type
Operating instructions

Etac RELAX is a backrest for shower seats, providing extra support and comfort during showering. It is easy to install, with strong adhesion when the glue area and fitting surface have a temperature of at least 20°C (68°F) and large pressure is applied. It takes 60 minutes for the glue to fully adhere, after which the backrest can withstand loads. RELAX is a valuable aid for individuals who need extra support and stability while showering, enhancing their safety and comfort.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents