Barco F50 1080 User guide

F50

User Manual

601–0307–00/02

25/02/2016

Barco Fredrikstad AS

Habornveien 53, N-1630 Gamle Fredrikstad, Norway

Phone: +47 6930 4550

Fax: +47 6930 4580

Support: Support.[email protected]

Visit us at the web: www.barco.com

Printed in N0

Changes

Barco provides this manual ’as is’ w ithout warranty of any kind, either expressed or implied, including but not limited to the implied w ar-

ranties or m erchantability and ﬁtness for a particular purpose. Barco m ay m ake improvements and/o r cha nges to the product(s) and/or the

program(s) described in this publication at any time without notice.

This pub lication could contain technical inaccuracies or typographical errors. Changes are periodically m ade to the information in this

publication; these c hanges are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site w

ww.bar co.com or from the secured Barco web site

h

ttps://www.barco.com/en/signin.

stored in a retrieval system without the prior written consent of Barco.

Federal Communications Commis sion (FCC Statement)

This equipment h as been tested and found to c omply with the limits for a class A digital device, pursuant to Par t 15 of the FCC rules.

These limits are designed to provide reasonable protection aga inst harmful interference when the equipment is operated in a comm ercial

environment. T his equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction m anual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may

cause harmful interference, in which case the user will b e responsible for correcting any interference at his own ex pense

Changes or modiﬁcations not expressly approved by the par ty responsible for compliance could void the user ’s authority to ope rate the

equipment

EN55022/CISPR22 Cla ss A ITE (Information Technology Equipment)

Class A ITE is a category of all other ITE which satisﬁes the class A IT

E limits but not the class B ITE limits. S uch equipment should not

be res tricted in its sale but the following warning shall be included in the instructions for use:

Warning : This is a class A product. In a domestic env ironment this product may cause radio interference in whic h case the us er may be

required to take adequate measures.

Guaran tee and Compensation

Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guarantee. O n receipt, the pu rchaser

must immediately inspect a ll delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco

must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,

at latest 30 days after the transfer of risks. In the event of justiﬁed notice of com plaint, Barco can repair the fault or provide a replacement

at its own discretion w ithin an appr opriate period. If this m easure proves to be impos sible or uns uccessful, the purchaser ca n demand a

reduction in the purchase price or c ancellation of the contract. All other claim s, in particular those relating to compensation for direct or

indirect damage, and also damage attributed to the operation of s oftware as well as to other services provided by Barco, being a component

of the system or independent service, will be deemed invalid provided the dam age is n ot pro ven to be attributed to the absence of properties

guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchase r or a third party carries ou

t m odiﬁcations or repairs on go ods delivered by B arco, or if the goods are ha ndled incorrectly,

in particular if the s ystem s are operated incorrectly or if, after the transfer o f risks, the goods a re subject to inﬂuences not agreed upon in

the contract, all guarantee claims o f the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures

which are attributed to pro grams or spe

cial electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as w ell as normal

maintenance are not subject to the guarantee p rovided by Ba rco either.

The environmental conditions as well as the servicing and maintenance regulations s peciﬁed in this m anual m ust be com plied with by the

customer.

Software License Agreement

You should carefully read the following terms and conditions before using this software. Your use of t his s oftware indicates your acceptance

of this license agreement and warranty.

Terms and Conditions:

1. No redistribution of the software is allowed.

2. Reverse-Engineering. You may not reverse engineer, decom pile, disassemble or alter this software product.

Disclaimer of Warranty:

This software and the ac com panying ﬁles are sold “as is” and without warranties as to performance or mer chantability or any other war-

ranties whether expressed or im plied. In no event shall Barco be liable for dam age of any kind, loss of data, loss of proﬁts, business

interruption or other pecuniary loss arising directly or indirectly. Any liability of the seller will be exclusively limited to replacement of the

product or refund of purchase price.

Trademarks

Brand and pr oduct names mentioned in this m anual may be trademarks, registered trademarks or c opyrights of their respective holders.

All br and and product names mentioned in this man ual serve as comments or examples and are not to be understood as advertising for

the products or their manufacturers.

Table of contents
TABLE OF CON TENTS
Introduction ......................................................................................................... 3
1 Welcome.............................................................................................................................. 4
2 About this manual . ................................................................................................................... 5
Safety................................................................................................................. 7
1 General Considerations .............................................................................................................. 8
2 Important safety instructions ......................................................................................................... 9
3 Product safety labels ................................................................................................................ 13
Getting to know the projector...................................................................................15
1 Introducing a small revolution....................................................................................................... 16
2 About the projector ..................................................................................................................17
3 Projector components ...............................................................................................................18
4 User interface........................................................................................................................19
5 Accessories.......................................................................................................................... 20
Lenses...............................................................................................................23
1 Lens range . . . ........................................................................................................................24
2 Installing a lens ......................................................................................................................25
3 Lens shift .............................................................................................................................26
4 Adjust zoom, focus and iris.......................................................................................................... 27
5 Lens lock.............................................................................................................................28
Installation .........................................................................................................29
1 Installing the projector............................................................................................................... 30
2 Installation conditions ...............................................................................................................31
3 Initial inspection......................................................................................................................33
4 Positioning the projector.............................................................................................................34
5 Mounting the projector on a ﬂat surface ............................................................................................36
6 Installing the projector to a ceiling mount or frame.................................................................................37
7 Throw distance ......................................................................................................................38
8 Lens shift and offset m atrix. ......................................................................................................... 40
9 Scheimpﬂ ug ( Boresight) adjustment ................................................................................................ 42
10 Scheimpﬂug adjustment.............................................................................................................43
Input and communication........................................................................................45
1 Local keypad......................................................................................................................... 46
2 Status indicator light.................................................................................................................47
3 Wireless remote control .............................................................................................................48
4 Connector Panel..................................................................................................................... 49
5 Connect to a source .................................................................................................................50
6 Extended Display Identiﬁcation Data (EDID) .......................................................................................51
7 HDBaseT ............................................................................................................................52
8 VGA..................................................................................................................................53
9 DVI-D ................................................................................................................................ 54
10 HDMI.................................................................................................................................55
11 Display Port 1........................................................................................................................56
12 Display Port 2........................................................................................................................57
13 LAN (Control) ........................................................................................................................58
14 RS232 (Control) ..................................................................................................................... 59
15 USB-A ...............................................................................................................................60
16 Sync 1 and 2......................................................................................................................... 61
17 Sync 3................................................................................................................................62
Change projector settings .......................................................................................63
1 Select a power mode................................................................................................................64
2 Lock the projector ...................................................................................................................65
3 Customize the On Screen Display (OSD) .......................................................................................... 66
4 Review and change network settings ............................................................................................... 67
5 Review system status ............................................................................................................... 68
6 Revert to factory settings............................................................................................................69
Set up the picture .................................................................................................71
1 Select the image orientation ........................................................................................................72
2 Use test images ..................................................................................................................... 73
3 Set up Picture-by-Picture............................................................................................................ 74
4 Apply a display proﬁle ...............................................................................................................75
5 Adjust lamp power...................................................................................................................76
6 Use gamma curves.................................................................................................................. 77
7 Adjust brightness, saturation and contrast.......................................................................................... 79
8 Choose an aspect ratio.............................................................................................................. 80
601–0307–00 F50 25/02/2016
1

Table of contents
Advanced picture adjustments .................................................................................81
1 Apply smear reduction processing (SRP) . . ........................................................................................83
2 Crop the image ......................................................................................................................84
3 Manual adjustments on VG A inputs ................................................................................................86
Color calibration...................................................................................................87
1 RealColor™ ......................................................................................................................... 88
2 BrilliantColor™ ...................................................................................................................... 90
3 Deﬁne the x,y coordinates for RGB(W).............................................................................................91
4 Use color temperature to adjust white point ........................................................................................ 92
5 Color calibration best practice.......................................................................................................93
6 Calibrate projector color.............................................................................................................94
Multichannel installations .......................................................................................95
1 Synchronization best practice....................................................................................................... 96
2 Synchronization concept for the F50 ............................................................................................... 97
3 The Installation — Synchronization menu ......................................................................................... 98
4 Synchronization menu 2D . . .........................................................................................................99
5 Synchronization menu 3D . . ........................................................................................................100
6 Troubleshoot source sync issues . .................................................................................................102
Stereoscopic multichannel setup ............................................................................ 105
1 AS3D modes. .......................................................................................................................106
2 AS3D synchronization best practice ...............................................................................................107
3 The 3D menu .......................................................................................................................108
4 Synchronous frame sequential.....................................................................................................109
5 Asynchronous frame sequen tial . . .................................................................................................110
6 Synchronous side by side . . ........................................................................................................111
7 Asynchronous side by side.........................................................................................................112
Color wheel....................................................................................................... 113
1 VizSim (RGB).......................................................................................................................114
2 VizSim Bright (RGB)................................................................................................................115
3 High Brightness MKIII (RGBC + White)............................................................................................116
User maintenance............................................................................................... 117
1 Replace the projector lamp.........................................................................................................118
2 Update the projector ﬁrmware......................................................................................................119
Technical Speciﬁcations ....................................................................................... 121
1 F50 1080............................................................................................................................122
2 F50 WUXGA........................................................................................................................123
3 F50 WQXGA........................................................................................................................124
4 F50 Panorama ......................................................................................................................125
Environmental information .................................................................................... 127
1 Disposal information................................................................................................................128
2 RoHS compliance ..................................................................................................................129
3 Production address .................................................................................................................131
2
601–0307–00 F50 25/02/2016

1. Introduction

1. INTRODUCTION

Overview

•Welcome

• About this manu al

601–0307–00 F50 25/02/2016

3

1. Introduction

1.1 Welcome

Welcome!

Congratulations on your purchase of a Barco F50 projector! T he F50 projectors are part of a proud tradition of quality projectors built

for superior performance, and feature compact footprint, high performance optics and lenses, excellent resolution, Active S tereo 3D

capabilities and built-in frame-lock synch ronization.

4

601–0307–00 F50 25/02/2016

1. Introduction

1.2 About this manual

General

We recommend you read this user manual before setting up and o perating y our projec tor for the ﬁrst time. F am iliarizing yourself

with the projectors’ features and functions, as well as its safety a nd maintenance f eatures, will help ensure you enjoy m any years

of hassle-free projection.

Following is a brief overview of how information in the manual is org anized and presented.

The content in this manual is s ystematized primarily by function, and then topic.

On the ﬁrst pa ge of each chapter is an overview of the chapter contents.

A menu path is expressed in the following manner: Main Me nu — Sub Menu — Sub sub menu . For example, Main Menu —

Installation — Synchronization

All physical m easur ement units given in this manual are according to the International Standard of Units (SI units). C onversion from

this to other measurement units is the responsibility of the u ser.

Illustrations used in the manu al are for general reference only, and may differ from your product.

601–0307–00 F50 25/02/2016

5

1. Introduction

6 601–0307–00 F50 25/02/2016

2. Safety

2. SAFETY

About this chap ter

Read this chapter thoroughly before attempting to install or operate the projector.

To prevent personal injury to users or physical dam age to the projector while installing and using your projector, ensure that you

understand and follow all safety guidelines, instructions and w arnings inc luded in this chapter and this manual.

Overview

• General Considerations

• Important safety instructions

• Product safety labels

601–0307–00 F50 25/02/2016

7

2. Safety

2.1 General Considerations

General safety instructions

• Before operating this equipment please read this manual thoroughly and retain it for future reference.

• All warnings on the projector and in the docum entation manuals shall be adhered to.

• All instructions for operating and use of this equipmen t shall be followed precisely.

• All local installation codes shall be adhered to.

Owner ’s record

The part n umber and serial number are printed on a label which is stuck on the respective part. Record these numbers in the spaces

provided below. Refer to them wh enever you c all upon your Barco dealer regarding this product.

Product article n umber

Product s erial number

Dealer

General conditions for us e

• Use only the cables and cords supplied with the projector or or iginal replacem ent cables. U sing other cables or cords m ay lead

to malfunction and permane nt damage to the unit.

• Always use a g rounded (3–pronged) power cord to ensure proper grounding of the unit. Never us e 2-pronged power cords, as

this is dangerous and could lead to electrical shock.

• Do not attempt to open the projector unit. The projector contains no use r serviceable parts. Refer all repairs to qualiﬁed per-

sonnel only. Make sure that n o objects enter into the vents and openings

of the chassis.

• Do not s pill any liquids on the projector or into the vents or openings of the unit.

• Always remove the lens cap before switching on the projector. I f the lens cap is not removed, it may melt due to the high energy

light emitted through the lens. Melting the lens cap may perm anently damage the surface of the projection lens.

• Only p lace the projector on a stable sur face, or mount it s ecurely using an ap proved ceiling-mount.

• Always operate the pr ojector acco rding to the rotation guidelines. Operating the unit in other positions may reduce lamp life

signiﬁcantly, and may lead to overheating, re sulting in malfunctioning

.

• Always allow am ple airﬂow through the pr ojector. Never block any of the air vents. Never cover the unit in a ny way while

running. Allow for sufﬁcient dis tance to walls and c eilings to avoid ov erheating.

• Minimum safety (clearance) distance to the sides and rear of the unit is 50cm / 20” in any direction (15 cm/ 6” to ceiling).

• Hot air is exhausted from the rear vent. D o not place objects that are sensitive to heat nearer than 50c m / 20” to the exhaust

vent.

• The projector is designed for indoor use only. Never operate t

he unit outdoors.

• Do not op erate the projector outside its temperature and humidity s peciﬁc ations, as t his may result in overheating and malfunc-

tioning.

• Only connect the projector to signal sources and voltages as described in the technica l speciﬁcation. Connecting to unspeciﬁed

signal sources or voltages may lead to m alfunction and permanent damag e of t he unit.

• Wherever possible, use main pow er supply with surge protection to prevent damage to the projector caused by unscheduled

power surges.

• Allow lamp to cool down for at least 60 m inutes before changing. USE ONLY ORIGIN AL LAMPS .

• Connecting sources to a powered projector may result in product failure. It is recom mended that the power cable connector

(projector-end) or the mains power socket is accessible whilst the product is in use to enable mains power to be disconnected

or switched off when connecting source devices. This s hould be considered during product installation.

8

601–0307–00 F50 25/02/2016

2. Safety

2.2 Important safety instructions

To prevent the risk of electrical shock

• This projector should be operated from an A C power source. Ensure that the m ains voltage and capacity matches the projector

electrical ratings. If you are unable to install the AC requirements, contact your electrician. Do not defeat the purpose of the

grounding.

• Installation according to the local electrical code and regulations by qualiﬁed technical personnel only.

• A readily accessible disconnect device mu st be incorporated externally to the equipment for removal of the power to the pro-

jector cord.

• Warning: High leakage current. Earth connection essential before connecting supply.

• Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the cord.

• Do no t op erate the projector w ith a damaged cord or if the projector has been dropped or damaged - until it has been examined

and approved for operation by a qualiﬁed service technician.

• Position the cord so that it will not be tripped over, pulled, or c ontact hot su rfaces.

• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated

for less amperage than the projec tor may overheat.

• Never push objec ts of any kind into this pr ojector through cabinet s lots as they may touch dangerous voltage po ints or short

circuit parts that could result in a risk of ﬁre or electrical shoc k.

• Do not expose this projector to rain or moisture.

• Do not immerse or expose this projector in w ater or other liquids.

• Do not spill liquid of any kind on this projector.

• Should any liquid or solid object fall into the cabinet, unp lug the set and hav e it checked by qualiﬁed service personnel before

resuming op erations.

• Do not disassemble this projector, always take it to a t rained service person when service or repair work is required.

• Do not use an accessory attachm ent which is not r ecom mended by the m anufacturer.

• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for

long periods of time, r emov e all power from the projector. This will pr event damage to the projector due to lightning and AC

power-line surges.

601–0307–00 F50 25/02/2016

9

2. Safety

To prevent personal injury

• Isolate electrically before replacing the lamp or lamp hous e. Caution: Hot lam p (house).

• Caution: High pressure lam p may explode if improperly handled. Refer servicing to qualiﬁed service personnel.

• To prevent injury a nd physical damage, always read this manual and all labels on the system before inserting the lamp casing,

powering the projector or adjusting the pr ojector.

• To prevent injury, ensure that the lens and all cover plates are correctly installed. See installation procedures.

• Warning: high intensity light beam. NEVER look into the lens ! High luminance c ould result in damage to the eye.

• Warning: e xtremely high b rightness lamp s: T his projector uses extremely high brightness lamps. Never attempt to

look

directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 m eters

away from the projected image. Avoid close range reﬂection of the projected image on any reﬂecting surface ( such as glass,

metal, … ) . W hen operating the projector, we strongly recommend wearing suitable sa fety g lasses.

• Before attempting to re move any of the projector’s covers, disconnect the projector power cord for removal of all power from

the projector.

• When required to rem ove all power from the projector, to access parts inside, always disconnect the projector power cord for

removal of all power from the projec tor.

• Do not place this equipment on an unstable cart, stand, or table. The product m ay fall, causing serious damage to it and

possible injury to the user.

• It is hazardous to operate without lens or shield. Lenses, s hields or ultra violet screens shall b e changed if they hav e become

visibly damaged to such an extent that their effectiveness is im paired. For example by cr acks or deep scratches.

• Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is

an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin

hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary e xposure. Protect yourself and

your employees by making them aware of the hazards and how to protect thems elves. Protecting the skin can be accom plished

by w earing tightly woven garments and gloves. P rotecting t he eyes from UV c an be accomplished by wea ring safety glasses

that are designed to provide UV pr otection. In addition to the UV, the visible light from the lamp is intense and should also be

considered when ch oosing pr otective eye wear.

• Mercury Vapor Warnings: Kee p the following w arnings in m ind when us ing the projector. The lamp used in the projector

contains m ercury. In case of a lamp r upture, explosion there w ill be a m ercury vapor emission. In order to m inimize the potential

risk of inhaling mercury vapors:

- Ensure the projector is installed only in ventilated room s.

- Replace the lamp module before the end of its operational life.

- Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a preg-

nant wom an).

- Seek medical attention if unusual health conditions oc cur after a lamp rupture, explosion, such as headache, fatigue, short-

ness of breath, chest-tightening coughing or nausea.

• Exposure to UV radiation: Som e medications are known to make individuals extra sensitive to UV radiation. The American

Conference of Governmen tal Indus trial Hygienists (ACGIH) recommend s occupational UV e xposure for an-8 hour day to be

less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure

employees are not expos ed to cumulative radiation levels exceed ing these government guidelines.

WARNING: This product contains chemicals, including lead, known to the State of California to cause birth

defects or o ther rep roductive harm. Recycle pro perly, d o not dispose of in ordinary waste!

WARNING: Service personnel must use eye and skin protection during servicing.

10 601–0307–00 F50 25/02/2016

2. Safety

To prevent ﬁre hazard

• Do not place ﬂamma ble or combustible materials near the projector!

• Barco large s creen projection products are designed and manufactured to m eet the most stringent safety regu lations. T his

projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and

safe. Exposing ﬂammable or combustible materials into close p roximity of this projector c ould result in the spontaneous ignition

of that m aterial, resulting in a ﬁre. For this reason, it is absolutely ne cessary to leave an “ex clusion zone” around all external

surfaces of the projector whereby no ﬂam mable o r combustible m aterials are p resent. The exclusion zon e must be not less

than 40 cm (16”) for all DLP Cinema projectors. The ex clusion zone on the lens side mu st be at least 5 m

. Do not cover the

projector or the lens with any material while the pr ojector is in operation. Keep ﬂammable a nd com bustible materials away from

the projector at all times . Mount the projector in a well ventilated area away from s ources of ignition and out of direct sun light.

Never expose the projector to rain or moisture. In the event of ﬁre, use sand, CO

2

or dry powde

r ﬁre extinguishers. Nev er use

water on an electrical ﬁre. Always have service perform ed on this projector by authorized Barco service personnel. Always

insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this

projector.

• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector an d to protect

it from overheating, these openings must not be blocked or covered. The ope nings should never be blocked by placing the

projector too clos e to walls, or other s imilar surface. This projector should never be placed near or over a radiator or heat

register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot e xhaust air from

console to the outside of the building.

• Let the projector cool completely before s toring. Remove cord from the projector when storing.

• Heat sensitive materials should not be placed in the path of t he exhaust air or on the lamp house.

To prevent projector damage

• This projector has been d esigned for use with a speciﬁc lamp (hous e) type. See installation instructions for its correct type.

•Theairﬁlters of the projector must be cleaned or replaced on a regular basis (a "clean" booth would be m onthly-minimum).

Neglecting this could res ult in disrupting the air ﬂow inside the projector, causing ov erheating. Overheating may lead to the

projector shutting down during operation.

• The projector m ust always b e installed in a manner which ensures free ﬂow of air into its air inlets.

• In order to ensure that correct airﬂow is maintained, and that the projector complies with E lectromagnetic C om patibility (EMC )

and sa fety requirements, it should always be operated with all of it’s c overs in place.

• Slots and openings in the cabinet are pro vided for ventilation. To ensure reliable operation of the produc t and to protect it from

overheating, these openings mus t not be bloc ked or covered. T he openings should never be blocked by plac ing the p roduct

on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. T he

device shou ld not be plac ed in a built-in installation or enclosure unless proper ventilation is provided.

• Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and rem ove all power

from the projector. Do not operate the projector again until it has been chec ked by qualiﬁed service personnel.

• Do not block the pr ojector cooling fans or free air movement around the projector. Loose papers or other objec ts may not be

nearer to the projector than 10 cm (4") on any si

de.

• Do not us e this equipment near water.

• Proper oper ation of the projector can only be guar anteed in table mounting. It is not permitted to use the projector in another

position. See installation procedure for correct installation. A ceiling mount w ill be supported in the future.

• Special care for Laser Beam s: Special care should be used when DLP projectors are us ed in the same room as high pow er

laser equipment. Direct or indirect hitting o f a laser beam on to the lens can severely da mage the Digital Mirror Devices

TM

in

which case there is a loss of warranty.

• Never place the projector in direct sunlight. Sunlight on the lens c an severely damage the Digital Mirror Devices

TM

in which

case there is a loss of warranty.

• Save the original shipping carton and packing material. They will come in handy if y ou ever have to ship y our equipm ent. For

maximum protection, repac k your set as it was originally pack ed at the factory.

• Disconnect the power to the projector before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning. Nev er use strong solvents, s uch as thinner or benzine, or, patrol, or abrasive cleaners, since these will damage the

cabinet. Stubborn stains may be remov ed with a cloth lightly dampened with m ild detergent solution.

• To ensure the highest optical performance and resolution, the projection lenses are specially treated with an an ti-reﬂective

coating, therefore, avoid touching the lens. To remove dust on the lens, use a so ft dry cloth. Do not use a damp cloth, detergent

solution, or thinner.

• Rated maximum ambient temperature, t

a

= 35°C (95°F).

• The lamp hou se shall be r eplaced if it has become damaged or thermally deform ed.

601–0307–00 F50 25/02/2016

11

2. Safety

On servicing

• Do not attempt to service this pr oduct yourself, as o pening or removing covers may expose you to dangerous voltage potentials

and risk of electric s hock.

• Refer all servicing to qualiﬁed s ervice personnel.

• Attempts to alter the factory-set internal c ontrols or to change o ther control settings not specially discussed in this m anual c an

lead to permanent dam age to the pr ojector and cancellation of the warranty.

• Remove all po wer from the projector and refer servicing to qualiﬁed service technicians under the following conditions:

- When the power cord or plug is da maged or frayed.

- If liquid has bee n spilled into the equipment.

- If the product has b een expo sed to rain or water.

- If the product does not operate norm ally wh en the operating instructions are followed. Adjus t only t hose controls that are

covered by the operating instructions since im proper adjustment of the other c ontrols may result in dam age and will often

require extensive work by a qualiﬁed technician to restore the product to normal operation.

- If the product has been dropped or the cabinet has been damaged.

- If the product exhibits a distinct change in per formance, indicating a need for service.

• Replacement pa rts: W hen replacement pa rts ar e r equired, be sure the service technician has us ed original Barco replac ement

parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu-

tions may result in degraded performance and reliability, ﬁre, electric shock or other h azards. Unauthorized substitutions may

void warra nty.

• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks

to determine that the pr oduct is in proper operating condition.

• Possible explosion hazard: Always keep in mind the caution below:

To prevent battery explosion

• Danger of explosion if battery is incorrectly installed.

• Replace only with the same or equivalent type recommended by the manufacturer.

• For disposal of used batteries, always consult federal, state, local a nd provincial hazardous waste disposal rules and regulations

to ensure proper disposal.

12

601–0307–00 F50 25/02/2016

2. Safety

2.3 Product safety labels

Product safety labels

Label image Label description

The Lam p House is v ery h ot after operation. To avoid burns, let the projector

cool down for at least 60 minutes before p roceeding to remov e the Lamp

House.

General Warning H azard

Electric Volta ge Haz ard

Hot Surface Hazard

UV Haza rd

Hazardous moving parts.

Keep away from moving fan blades.

Keep ﬁngers and other body parts away.

601–0307–00 F50 25/02/2016 13

2. Safety

14 601–0307–00 F50 25/02/2016

3. Getting to know the projector

3. GETTING TO KNOW THE PROJECTOR

Overview

• Introducing a small revolution

• About the projector

• Projector components

• User interface

• Accessories

601–0307–00 F50 25/02/2016

15

3. Getting to know the projector

3.1 Introducing a small revolution

A world best in ﬁt and function

The F50 is the m arket’s brightest, sharpest and mos t compact 120Hz single chip D LP® projector.

Image 3-1

Unmatched imagery

•1ChipDLP®

• Wide range of resolutions

• High P erformance Optics

• Custom-designed smear r eduction technology

• High A NSI contrast

Built fo r th e chall e nge

• Compact footprint and weight

• Motion platform warranted (3G Certiﬁed)

• Optical locking s ystem s

• Minimal m aintenance requirements

Ideal for multichannel installations

• Large depth of focus (DoF)

• Unmatched sharpness

• RealColor™ Color Managem ent

• Color batch matching for quicker and easier color calibration in color critical a pplications

16

601–0307–00 F50 25/02/2016

Page is loading ...

Barco F50 1080 User guide

This manual is also suitable for

Barco F50 1080 User guide

Related papers

Other documents