Page is loading ...
PAGE [2]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
Introduction
Congratulations on your purchase of Century Helicopter Product’s newest RC helicopter model. The Century 50NX is a new breed of
helicopter, ideal for beginners new to the hobby through to expert pilots. The Century 50NX can be setup for a multitude of flight styles
- from the beginner to intermediate pilot and on up to the most advanced 3D aerobatic flights. This kit will exceed your expectations for
precision control at an affordable price.
Warning
This radio controlled model is not a toy! It is a precision machine requiring proper assembly and setup to avoid accidents. It is the
responsibility of the owner to operate this product in a safe manner as it can inflict serious injury otherwise. It is recommended that if
you are in doubt of your abilities, seek assistance from experienced radio control modelers and associations. Keep loose items that can
get entangled in the rotor blades away for the main and tail blades, including loose clothing, hair, or other objects such as pencils and
screwdrivers. Especially keep your hands away from the rotor blades. As manufacturer, we assume no liability for the use of this product.
Pre-assembly Information
Upon opening the kit, all the major component parts are bagged for ease of assembly which correspond to the sections of the manual.
Various assemblies have been pre-assembled however, only as a reference assembly. Final assembly is up to the user. Installation onto
the particular parts, screws and nuts required for each step are packaged in the same bag as the parts. Be careful when opening each
bag as not to lose any hardware. Care has been taken in filling and packing of each bag however mistakes do happen. If there is a parts
shortage or missing hardware please contact us at:
General Guidelines
Apply thread lock to all metal to metal thread contact points. Do not apply CA (cyanoacrylate) glue or thread lock to ny-lock nuts (metal nuts
with plastic inserts). Diagrams indicated by bounding boxes for screws, bearings, etc. are illustrated at a 1-to-1 ratio. All other illustrations
are not drawn to scale. Throughout this manual, you will find building tips. Please follow the tips and use common sense when building.
Century Helicopter Products
1740-C Junction Ave.
San Jose, CA. 95112
www.centuryheli.com
BUILDING INSTRUCTIONS FOR THE 50NX
Century Helicopter Products warranties that the Products purchased (the “Product”) will be free from defects in materials and workman-
ship 30 days from the date of purchase by the Purchaser.
Warranty Period
Required Items
(a) This warranty is limited to the original customer (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products purchased
from an authorized Century Helicopter Products dealer. Third party transactions are not covered by this warranty. Proof of purchase is
required for warranty claims. Further, Century Helicopter Products reserves the right to change or modify this warranty without notice
and disclaims all other warranties, express or implied.
(b) Limitations- CENTURY HELICOPTER PRODUCT MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOWLEDG-
ES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.
(c) Purchaser Remedy- Century Helicopter Products’s sole obligation hereunder shall be that Century Helicopter Products will, at its
option, (i) repair or (ii) replace, any Product determined by Century Helicopter Products to be defective. In the event of a defect, these
are the Purchaser’s exclusive remedies. Century Helicopter Products reserves the right to inspect any and all equipment involved in
a warranty claim. Repair or replacement decisions are at the sole discretion of Century Helicopter Products. This warranty does not
cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any
part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by
anyone other than Century Helicopter Products. Return of any goods by Purchaser must be approved by Century Helicopter Products
before shipment.
Limited Warranty
Flight Guidelines
Please note this checklist is not intended to be a replacement for the content included in this instruction manual. Although it can
be used as a quick start guide, we strongly suggest reading through this manual completely before proceeding.
Always turn the transmitter on first
Allow the gyro, and receiver to arm and initialize properly
Do a pre-flight check making sure all electronics are working and look for any mechanical issues
Fly the model
Land the model
Turn off the engine
Always turn the transmitter off last
CN2050
PADDLE GAUGE
CN2034A
BALL LINK PLIERS
HOBBY KNIFE
RECEIVER BATTERY
SERVOS X 5
ZIP TIES
4-WAY WRENCH
GYRO
6 CHANNEL RECEIVER
(MINIMUM)
HOBBY SCISSORS
GLOW PLUG
IGNITOR
METRIC RULER OR
SIMILAR MEASURING
DEVICE
CN2017
HEX DRIVERS
1.5, 2.0, 2.5, 3.0 & 4.0
6 CHANNEL
CCPM TRANSMITTER
(MINIMUM)
NITRO HELICOPTER
FUEL
CN3038A
SILENT POWER
50 MUFFLER
CN266166C
ROTORTECH 610MM BLADES
50 SIZE NITRO
ENGINE
CN2027
G-FORCE PITCH GAUGE
CN2051
ACCURATECH BLADE BAL-
ANCER V.2
CN2255
CONTROL ROD
SETUP GAUGE
CN2057 & CN0426
STARTER
AND STARTER SHAFT
NEEDLE NOSE
PLIERS
SYNTHETIC
OIL/GREASE
1.000
PAGE [3]
1
3
7
2
6
4
编号
数量（PCS）
序号
1
2
3
4
5
6
2
2
2
2
2
2
7
8
CNBB0730
(M3球头螺丝芽长6.5MM)
(平衡杆固定片)
(轴承)
(平衡控制臂)
CNBB0840
(轴承)
HI3167B
HI3167G
HI3167E
8
9
5
CNM3X14BHCS
HI3167G
(伞头螺丝)
(铁套)
2
2
1
(主旋翼中心座)
HI3160D
9
CNM3X6BHCS
(伞头螺丝)
METAL ROTOR HEAD YOKE SET
BUTTON HEAD CAP SCREWS M3 x 6
3X7X3 BALL BEARING
SEESAW TIE BAR SET
SEESAW OFFSET PLATES
SPECIAL BALL M3 x 6
4X8X3 BALL BEARING
SEESAW TIE BAR SET
BUTTON HEAD CAP SCREWS M3 x 14
名称（英文-中文）
DESCRIPTION
HEAD ASSEMBLY
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
CNM3X14BHCS
CNBB0730
CNBB0840
HI3167E
HI3167E
CNM3X6BHCS
CA
BAG 1
In Bag 2, there is a small poly-bag of various extra/spare
screws and a bottle of medium strength thread lock. Use
this thread lock when indicated.
Take special care when pressing in these bearings. Do not
press in on the inner race of the bearing.
Do not secure all the screws until lining up
the components in the following steps.
PAGE [4]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
FLYBAR ASSEMBLY
1
2
3
4
5
6
7
9
8
编号 数量（PCS）
序号
1
2
3
4
5
6
2
2
2
2
2
2
7
(拉杆)
(球头连接头)
CNM4X5SS
(稳定翼控制臂)
(M3球头双牙螺丝)
(平衡杆控制臂)
(圆头螺丝)
CNM3X12BHCS
(无头内六角螺丝)
2
8
(平衡杆)
1
9
(平衡翼)
2
HI3176C
HI3176C
HI3176C
HW3173A
HI6179
HI6145
HW3192A
4MM FLYBAR
BALL LINK SET (26 LONG,4 SHORT)
M4X5 SOCKET HEAD SET SCREW
PUSHROD SET
SYMMETRICAL FLY BAR ARMS
SYMMETRICAL FLYBAR ARM
名称（英文-中文）
DESCRIPTION
SYMMETRICAL FLYBAR ARM
CNM3X12BHCS
CNM4X5SS
HI3167C
CA
Make sure the distance on
both sides are equal.
Flybar weights are provided for
optional stability. Use the supplied
M3x3 set screw to set in place
on the flybar. Set the weights as
far out towards the paddles for in-
creased stability and closer to the
head block for increased response.
Make sure the distance on
both sides are equal.
Black = 30g
for stability
Yellow = 22g
for aerobatics
BAG 1, 6
10
CNLR1006
BUTTON HEAD CAP SCREWS M3 x 12
M4X6X0.5 WASHER
M4X6X0.5 WASHER
Be sure to attach these links prior
to securing screws.
10
4MM 30GRAM 3D NX FLYBAR PADDLES
PAGE [5]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
BLADE GRIP ASSEMBLY
Comes pre-assembled
Do not apply CA or
thread lock to locknut!
Do not overtighten
this locknut.
Notice orientation
of blade grips.
LARGER ID TOWARDS THE GRIP
SIDE PROFILE - BLADE GRIP
RECESSED CREVICE FACES MAIN SHAFT
THRUST BEARING INSTALLATION GUIDE
GROOVES INSIDE
编号
名称（英文-中文）
数量（PCS）
序号
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
(六角螺帽)
2
(止推轴承)
CNBB1260T
HW3180A
2
(平面垫片)
4
(轴承)
CNBB1360
2
(主旋翼夹片)
HI3184
2
HI3189A
(平面垫片)
(轴承)
CNBB0730
4
HI3189A
(铁套)
2
2
(球头螺丝)
CNLR1014
HI3189A
(主桨控制臂)
2
2
(有头内六角螺丝)
(球头螺丝)
CNLR1016A
2
HW3180A
1
HW3180A
2
(横轴)
(垫片)
6X12X4.5 THRUST BEARING
6x13x5 BALL BEARING
MAIN ROTOR BLADE GRIP SET
WASHER
STAINLESS BALL, 3mm THREAD, MEDIUM
6mm FEATHERING SHAFT
SPACER
3X7X3 BALL BEARING
SPACER
BELL MIXER ARM SET
M5 LOCK NUT
DESCRIPTION
CA
BAG 1
Step facing
blade grip for
Slower re-
sponse
Step facing
Away from
Blade grip
For faster
response.
CNM3X14CS
CNM5LOCK
M3X14 SOCKET HEAD CAP SCREW
STAINLESS BALL, 3MM THREAD, SHORT
6x10 FLAT WASHER
CNBB0730
M3X14CS
M3X5
CNBB1360
CNBB1260T
M5
CNLR1016A
CNLR1014
平面垫片
M8X13
铁套
M3X5X3
HW3180A
HW3180A
HW3180A
HI3189A
HI3189A
HI3189A
15
HI3181
RUBBER DAMPENERS
2
1
2
4
5
6
12
9
3
14
15
13
8
7
10
11
PAGE [6]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
MOUNTING HEAD BLOCK AND TIMING YOKE
编号 名称（英文-中文） 数量（PCS）
序号
1
2
3
4
5
2
1
1
2
1
CNM3x18CS
CNM2.5x8CS
(有头内六角螺丝)
(剪型臂导拄)
(无头内六角螺丝)
(M3螺母)
CNM3x4SS
CNM3LOCK
M2.5X8 SOCKET HEAD CAP SCREW
DESCRIPTION
TIMING YOKE
M3 LOCK-NUT
(有头内六角螺丝)
M3X18 SOCKET HEAD CAP SCREW
M3X4 SOCKET HEAD SET SCREW
CNM2.5X8CS
CNM3X18CS
M3 LOCK NUT
CNM3X4SS
Do not apply CA or
thread lock to lock nut!
Do not over tighten!
Do not over tighten!
You may feel a light coat of anti-rust oil resi-
due on the main shaft. If you do, clean this
with alcohol prior to installation.
BAG 1, 2
3
2
5
4
1
HI3160D
PAGE [7]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
WASHOUT ASSEMBLY
CNM3X16BHCS
M3X5X0.5
CNBB0730
CNLR1015
CNLR1016A
HI3152C
M3X5X3
HI6205
CNLR1014
HI3152C
编号
名称（英文-中文）
数量（PCS）
序号
1
2
3
4
5
(插销)
1
1
1
2
2
(铜套)
(控制臂固定座)
HI3152C
(三角控制臂)
6
7
8
9
10
11
12
13
14
(轴承)
(球头螺丝)
(铁套)
(圆头螺丝)
(十字盘)
(摆臂)
HI3152C
HI3152C
HI3152A
HI3152A
CNBB0730
HI3152C
CNM3X16BHCS
15
CNLR1016A
HI3146C
CNLR1016A
(铜套)
(平面垫片)
(球头螺丝)
(球头螺丝)
(球头螺丝)
4
2
2
2
2
2
2
1
3
2
CNLR1015
CNLR1014
HI3152C
WASHOUT SET
RADIUS LINK w/ PIN
STAINLESS BALL, 3mm THREAD, MEDIUM
3X5X3SPACER
METAL CCPM SWASHPLATE
WASHOUT SET
WASHOUT SET
RADIUS LINK w/ PIN
3X7X3 BALL BEARING
WASHOUT SET
BUTTON HEAD CAP SCREW
WASHOUT SET
STAINLESS BALL, 3mm THREAD, LONG
STAINLESS BALL, 3mm THREAD,
STAINLESS BALL, 3mm THREAD, LONG
DESCRIPTION
Comes pre-assembled
CA
HW6205
BAG 1
9
8
7
6
5
4
1
2
3
10
11
12
15
13
14
PAGE [8]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
CONTROL ROD ASSEMBLY
编号
名称（英文-中文）
数量（PCS）
序号
1
2
3
4
5
2
6
7
8
(球头连接杆)
(球头连接杆)
(球头连接杆)
(球头连接杆)
(连杆)
(连杆)
(连杆)
(连杆)
2
2
2
2
2
2
2
HW3192A
HW3192A
HW3192A
HW3192A
PUSHROD SET
PUSHROD SET
PUSHROD SET
PUSHROD SET
DESCRIPTION
NOTICE SIZE OF HOLES ON BALL LINKS
THE SIDE WITH THE SMALLER HOLE
SHOULD FACE OUTWARDS
PART# CN2255: CONTROL ROD SETUP GAUGE
PART# CN2219A: BALL LINK
EASY DRIVER
HELPFUL TOOL:
HELPFUL TOOL:
HI6145
HI6145
HI6145
HI6145
BAG 1, 5
1
2
A
8
7
6
5
B
D
4
3
C
A
B
C
D
26
48
52
100
This setup will get you approximately +/- 12 degrees of pitch
BALL LINKS (26 LONG, 4 SHORT)
BALL LINKS (26 LONG, 4 SHORT)
BALL LINKS (26 LONG, 4 SHORT)
BALL LINKS (26 LONG, 4 SHORT)
PAGE [9]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
COUNTER GEAR ASSEMBLY
CNM4X4SS
CNBB1350
CNM3X10FHCS
M5X7X2
CN2224
1
2
3
4
5
6
7
8
9
10
4
4
编号
数量 （PCS）
序号
1
2
3
4
5
6
(齿轮)
(铜环间隔套)
(轴承)
1
1
4
3
4
1
CNM4X4SS
7
9
10
8
(传动轴)
(齿轮)
(单向轴承)
(
斜头螺丝)
(轴承盖)
(轴承座)
1
1
1
1
CNBB1350
CN2263K
CN2263K
CN2263K
CN2263F
CN2263D
CNM5X7X2BS
5x13x4 BALL BEARING
AUTO HUB ASSEMBLY (8mm)
M4X4 SOCKET HEAD SET SCREW
M5x7x2 BRASS SPACER
AUTO HUB ASSEMBLY (8mm)
AUTO HUB ASSEMBLY (8mm)
CONSTANT DRIVE SHAFT 50 SIZE - 8MM (8mm)
名称（英文-中文）
DESCRIPTION
BAG 2
M3X8 FLUSH HEAD CAP SCREWSCNM3X8FHCS
HW3045B
METAL DRIVE GEAR 14T NX
GRAY COUNTER GEAR 8.67:1 53T (8mm)
PAGE [10]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
MAIN GEAR ASSEMBLY
CNM3X16CS
CNBB1019
CNBB1980
M3
CNM4X4SS
编号
数量（PCS）
序号
1
2
3
4
5
6
(主轴)
(塑胶垫圈)
(间隔套)
1
1
1
1
1
1
CNBB1019
HW3053A
7
9
10
8
(伞齿轮)
(八角铝拄)
(有头内六角螺丝)
(轴承)
(螺帽)
1
3
1
1
(轴承)
(铜套)
(外扣环)
1
1
HW3054A
CNM3X16CS
CNBB1980
CNM3LOCK
CNM4X4SS
(无头内六角螺丝)
11
12
10mm MAIN SHAFT
14X19 WASHER
10x19x5 BEARING
MAST STOPPER
M3x16 SOCKET HEAD CAP SCREWS
8x19x6 MAIN SHAFT BALL BEARING
M3 LOCK-NUT
MAIN GEAR
CIR CLIP
M4X4 SOCKET HEAD SET SCREW
名称（英文-中文）
DESCRIPTION
1
2
3
4
5
6
11
10
9
8
7
12
BAG 2
From Step: Mounting Head
Block & Timing Yoke (Page 6).
This is attached to the head
block.
You will find another main
gear and counter gear pinion
included with your kit. This set
is for extreme 3D.
Do not thread lock this in
place yet. Do so after you’ve
installed this section into the
frame on the following step.
Preassembled
HI3107A
HI3056A
CN2263L BRASS RING
CN2263A
CN2263A
MAIN GEAR HUB
PAGE [11]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
INSTALLATION OF MAIN & COUNTER GEAR
1
2
编号
名称（英文-中文）
数量（PCS）
序号
1
2
3
1
1
(第一轴传动组合)
1
(右塑料侧板)
(主轴传动组合)
UPPER SIDE FRAMES
COUNTER GEAR ASSEMBLY
MAIN GEAR ASSEMBLY
3
DESCRIPTION
HI3108
BAG 2, 3
PAGE [12]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
ASSEMBLY & INSTALLING TORQUE DRIVE
CNM4X4SS
CNM3X4SS
CNBB1350
1
2
4
5
3
6
7
编号
名称（英文-中文）
数量（PCS）
序号
1
2
3
4
5
6
1
3
1
1
2
1
7
(传动轴)
(无头内六角螺丝)
CNM3X4SS
(传动轴接头)
(间隔套)
(轴承)
(伞齿轮)
(无头内六角螺丝)
2
CNBB1350
HW3057
CNM4X4SS
HI3154
TAIL DRIVE PRIMARY SHAFT with SPACER (TORQUE)
5x13x4 BALL BEARING
TAIL TRANSMISSION BEVEL GEAR
M4X4 SOCKET HEAD SET SCREW
TAIL DRIVE PRIMARY SHAFT with SPACER (TORQUE)
M3X4 SOCKET HEAD SET SCREW
DESCRIPTION
BAG 2
TORQUE TUBE DRIVE COUPLER
HW3059A
HW3059A
PAGE [13]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
INSTALLING FRAME REINFORCEMENTS
编号 名称（英文-中文） 数量（PCS）
序号
1
2
2
2
(六角铝柱)
HW3127
UPPER BEARING REINFORCEMENT BARS
HEX SPACERS
DESCRIPTION
1
2
BAG 2
HW3127C
PAGE [14]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
BUILDING ELEVATOR FRAME
编号
数量（PCS）
序号
1
(固定板)
1
(螺丝护套)
4
(有头内六角螺丝)
2
(有头内六角螺丝)
2
(螺母)
2
2
3
4
5
CNM3X10CS
CNLM3LOCK
ELEVATOR FRAME
MACHINED WASHER
M3 LOCK-NUT
名称（英文-中文）
DESCRIPTION
M3x10 SOCKET HEAD CAP SCREWS
1
2
3
4
5
HI3109
CN2218S
BAG 2, 4
CNM3X10CS
CNM3X8CS
M3 CNM3LOCK
Assembly of left frame section
is exactly the same
M3X8 SOCKET HEAD CAP SCREWCNM3X8CS
PAGE [15]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
INSTALLING ELEVATOR AND AILERON BELL CRANKS
1
2
3
4
5
5
13
14
10
11
12
15
10
2
(有头内六角螺丝)
(十字盘固定座)
(有头内六角螺丝)
(有头内六角螺丝)
(有头内六角螺丝)
(螺丝护套)
CNM3X10CS
CNM3X8CS
CNM3X25CS
CNM3X8CS
11
12
13
14
1
2
2
2
4
M3x10 SOCKET HEAD CAP SCREWS
ANTI-ROTATION BRACKET
M3x8 SOCKET HEAD CAP SCREWS
M3x25 SOCKET HEAD CAP SCREWS
M3x8 SOCKET HEAD CAP SCREWS
MACHINED WASHER
编号
名称（英文-中文）
数量（PCS）
序号
1
(铝座)
2
(轴承)
4
(控制臂)
3
(铁套)
2
(M3球头螺丝)
6
2
3
4
5
6
7
8
CNBB0730
(轴承)
1
2
CNLR1014
BEVELED BELL-CRANK SPACER
BELL-CRANK
3x7x3 BALL BEARING
(铁套)
(铁套)
9
STAINLESS BALL, 3mm THREAD, SHORT
MALE THREADED SPACER
4x7x2.5 BALL BEARING
FEMALE THREADED SPACER
1
CNM3X25CS
CNM3X10CS
CNM3X8CS
CNM3X18CS
CNBB0730
CNLR1014
HI3032C
CNLR1013
3X5X7
HI3031D
HI3031C
HI3031E
HI3031E
CNBB47
HW3118
CN2218S
BAG 2, 3, 4
When installing, make
sure swashplate guide
goes through.
HW6205
3x5x3
M3x5x3 SPACER
Comes pre-assembled.
5
5
5
6
7
3
DESCRIPTION
PAGE [16]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
CLUTCH, FAN AND ENGINE MOUNTING
1
2
3
4
5
6
7
8
9
10
11
8
12
13
M5X13
CNBB1218
M9X13
CNM5X6SS
To prevent this nut from backing out, it
is recommended to use stronger thread
lock here and make sure to let the thread
lock dry over-night prior to starting the
motor. When tightening this nut, tighten
until snug and only apply 1/4 additional
turn. We recommend the piston locking
tool (part #: CN2215ABL) or crankshaft
locking tool when installing this nut. M10
socket driver will be needed to secure
this nut.
Line up bottom extrusions
of fan with grooves in the
clutch shoe
Comes pre-assembled.
编号 名称（英文-中文） 数量（PCS）
序号
4
5
6
7
8
11
1
1
1
1
2
1
12
(风扇)
(平面垫片)
1
13
1
(离合器)
(轴承)
(齿轮)
(引擎)
HW3011
CNBB1218
1
1
(钢内六角压入环)
(起动铝座)
(无头内六角螺丝)
2
3
(斜头十字螺丝)
9
(离合器罩)
10
6
1
2
1
HI3010A
HI3010B
HI3010B
ALUMINUM STARTER CUP
COOLING FAN
COOLING FAN
CLUTCH SHOES
12x18x4 BEARING
CLUTCH GEAR ONLY (26T)
MACHINED CLUTCH BELL & LINING
ENGINE
DESCRIPTION
(有头内六角螺丝)
14
15
(引擎座)
1
HW3018A
4
CNM3X16CS
ENGINE MOUNT (46-50 size)
M3x16 SOCKET HEAD CAP SCREWS
CLUTCH GEAR ONLY (26T)
14
15
CNM3X16CS
HI3009A
HI3009A
HI3009A
HI3009A
HI3009A
INCLUDED
Engine is not included.
SPACER (COMES WITH ENGINE)
BAG 4
Notice position
of holes prior to
mounting engine.
5MM HEX ADAPTER
Disassemble the fan assem-
bly to install nut.
M10 NUT (COMES WITH ENGINE)
M5X6 BUTTON HEAD CAP SCREWS
PAGE [17]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
FUEL TANK ASSEMBLY
(塑料油管)
编号 数量（PCS）
序号
1
2
(弯铜油管)
1
3
4
5
6
7
8
9
10
(吸油嘴)
(直铜油管)
(塑料油管)
(油箱塞)
(油箱塞固定座)
(十字紧固螺钉)
(油箱盖)
(油箱)
HI3138B
1
1
1
1
1
1
1
1
1
HI3138B
HI3138B
HI3138B
HI3138B
HI3138B
HI3138B
HI3138B
HI3138B
HI3138B
500cc FUEL TANK
名称（英文-中文）
DESCRIPTION
500cc FUEL TANK
500cc FUEL TANK
500cc FUEL TANK
500cc FUEL TANK
500cc FUEL TANK
500cc FUEL TANK
500cc FUEL TANK
500cc FUEL TANK
500cc FUEL TANK
Bent tube
There will be one hole that is plugged.
Ensure you are using the holes that
are not plugged.
BAG 3
1
2
3
4
5
6
7
8
9
10
PAGE [18]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
MOUNTING FAN SHROUD & CANOPY STANDOFFS
BAG 2, 3, 5
4
5
CNM3X35CS
M3 CNM3LOCK
M3 THREADED EXTENSION ROD
1
2
3
(风扇护罩)
HI3020A
COOLING FAN SHROUD
编号
数量（PCS）
序号
1
1
2
(有头内六角螺丝)
2
(螺母)
2
2
3
CNM3X35CS
CNM3LOCK
名称（英文-中文）
DESCRIPTION
M3x35 SOCKET HEAD CAP SCREWS
LOCK-NUT
(双头螺丝)
1
4
5
(机头固定铝柱)
CANOPY STANDOFF
THREADED EXTENSION ROD
HW3127A
HW3127A
PAGE [19]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
BOTTOM PLATE & LOWER FRAME ASSEMBLY
5
6
7
编号
名称（英文-中文）
数量（PCS）
序号
1
(有头内六角螺丝)
6
2
3
4
(底板)
(铝柱)
(铝柱)
1
2
1
CNM3X8CS
BOTTOM PLATE
M3x10 SOCKET HEAD CAP SCREWS
DESCRIPTION
BOTTOM PLATE REINFORCEMENT BARS
BOTTOM PLATE REINFORCEMENT BARS
5
(脚架固定座)
4
(螺丝护套)
6
(有头内六角螺丝)
7
10
10
CNM3X12CS
LANDING STRUT STANDOFFS
MACHINED WASHERS
M3x12 SOCKET HEAD CAP SCREWS
1
2
3
4
CNM3X12CS
CNM3X8CS
HI3113
HI3112 LOWER FRAME SET
8 2
HI3113A
HI3113A
HW3208
CN2218S
BAG 3, 4
Before assembly, build the bottom
plate first.
Longest piece.
FRONT
BACK
Build this first.
Dry fit these slots. If you no-
tice a tight fit, use the supplied
sandpaper and slowly sand
the bottom plate.
8
PAGE [20]
COPYRIGHT (C) CENTURY HELICOPTER PRODUCTS - ALL RIGHTS RESERVED
FRAME ASSEMBLY
8
1
2
3
4
5
7
6
9
CNM3X30CS
CNM3X12CS
CNM3X10CS
M3
CNM3X8ST
编号
名称（英文-中文）
数量（PCS）
序号
1
2
(十字自攻螺丝)
(有头内六角螺丝)
(有头内六角螺丝)
(螺丝护套)
CNM3X8ST
CNM3X10CS
CNM3X12CS
2
3
4
5
6
2
2
2
6
(有头内六角螺丝)
(M3螺母)
CNM3X12CS
(排气管)
CNM3LOCK
2
1
7
8
(尾支柱座)
2
9
2
(有头内六角螺丝)
CNM3X30CS
M3x8 PHILLIPS TAPPING SCREWS
DESCRIPTION
TAIL BOOM BREAK-AWAY SUPPORT
M3 LOCK-NUT
MUFFLER
M3x12 SOCKET HEAD CAP SCREWS
M3x12 SOCKET HEAD CAP SCREWS
M3x10 SOCKET HEAD CAP SCREWS
MACHINED WASHER
M3x30 SOCKET HEAD CAP SCREWS
If your muffler sits
too close to the
frames, you will
need to use an
extension.
INCLUDED
The muffler is not included
with the kit only: CN1063
CN2218S
HI3204
CN3038B
BAG 2, 4
/
