VISUAL COMFORT ARN 4172 User manual

Type
User manual
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from canopy (E) by removing threaded
nuts (F).
3. Using mounting plate (C) as a guide, line up with the junction box and
mark anchor positions.
4. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (T) into the holes using hammer.
5. Install mounting plate (B) to the junction box and secure with
mounting screws (D), then secure wood screws (U) to anchors (T).
6. Run support cable through hole on back of mounting plate (B). Loosen
cable lock and install to end of support cable. Insert other end of cable
through the cable lock and tighten ends with a screwdriver to secure.
(see diagram 2)
7. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
NOTE: It is imperative that the fixture is grounded.
8. Connect fixture neutral wire (white) to the supply neutral wire (usually
white) using wire nut (A).
9. Connect fixture hot wire (black) to the supply hot wire (usually black)
using the wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
Liscia Large Flush Mount
Item # ARN 4172
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
T
A
B
U
C
E
D
K
L
G(30PCS)
H(30PCS)
G(30PCS)
H(30PCS)
G(30PCS)
G(30PCS)
J(24PCS)
J(18PCS)
I(12PCS)
M
Diagram 1
Diagram 2
Bulbs not included
Slotted Screwdriver
NOTICE:
US
M
L
I
D
S
E
T
Crystal G(160PCS) Crystal H(60PCS) Crystal I(12PCS) Crystal J(42PCS)
Pliers
10. Make sure all wire connections are tight, then carefully tuck into the
junction box.
11. Install canopy (E) to mounting plate (B) and secure with threaded
nuts (F).
12. Install light bulbs into sockets.
Crystal Assembly - Use diagrams labeled Layer 1 - Layer 3 to complete
crystal assembly below:
1. Hang crystals (I, J & H) to bottom ring (Layer 1) starting from inside
and working your way out. Secure using provided pliers.
2. Hang the rest of crystals (H) onto rings from medium (Layer 2) and
working your way to the top ring (layer 3) . Secure using provided
pliers.
3. Hang crystals (G) to bottom ring (Layer 1), working your way to the
top ring (layer 3). Secure using provided pliers.
4. Thread finial (L) to nipple (K).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
Liscia Large Flush Mount
Item # ARN 4172
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
US
M
L
I
D
S
E
T
Layer 3 Layer 2
Layer 1
GGG
G
G
G
G
G
G
G
G
G
G
G
G
H
H
H
H
H
H
H
H
H
H
H
HHHHHH
H
H
H
H
H
H
H
H
H
H
H
H
G
G
G
G
G
G
G
G
G
G
G
G
G
GG
HH
G
H
H
H
H
H
H
H
H
H
H
H
H
HHHHHH
H
H
H
H
H
H
H
H
H
H
H
G
G
G
G
G
G
G
G
G
G
G
G
GGGG
G
G
G
G
G
G
G
G
G
G
G
G
G
H
H
H
H
H
H
H
H
H
H
H
H
HHHHHH
H
H
H
H
H
H
H
H
H
H
H
H
G
G
G
G
G
G
G
G
G
G
G
G
G
GGGGG
G
G
G
G
G
G
G
G
G
G
G
G
J
J
J
J
J
J
J
J
J
JJJJJJ
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
JJ J JJ
J
J
J
J
J
I
I
I
IIIII
I
I
I
I
  • Page 1 1
  • Page 2 2

VISUAL COMFORT ARN 4172 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI