2. ALARM COM
  3. ADC-S40-T
ADC-S40-T

ALARM COM ADC-S40-T Installation guide

  • Hello! I have analyzed the provided user guide for the Alarm.com Temperature Sensor ADC-S40-T. This document describes how to enroll, delete, and reset the device on a Z-Wave network using SmartStart, S2, or S0 methods. It also includes instructions on using the LED indicator and tamper switch. I'm ready to help with any questions you have about using this device.
  • How do I enroll the Temperature Sensor as a SmartStart device?
    How do I enroll the Temperature Sensor as an S2 device?
    How do I delete the Temperature Sensor from the Z-Wave network?
    How do I reset the Temperature Sensor?
Enroll, delete, or reset an Alarm.com Temperature Sensor (ADC-S40-T)
The Alarm.com Temperature Sensor (ADC-S40-T) can be enrolled into or deleted from a Z-Wave network following the
instructions below.
For more information about installing an Alarm.com Temperature Sensor (ADC-S40-T), see Alarm.com Temperature
Sensor (ADC-S40-T) - Installation Guide.
To enroll the Alarm.com Temperature Sensor (ADC-S40-T)
As a SmartStart device:
It is recommended to enroll this device as a SmartStart device to eliminate the need to put Z-Wave controllers into Add
Mode or to trigger devices (as is the case when enrolling non-SmartStart S2 devices).
For information about SmartStart compatibility and the enrollment process, see Add or remove a Z-Wave SmartStart-
enabled device.
As an S2 device:
If the Z-Wave controller is not SmartStart-compatible, it is recommended to enroll this device as an S2 device for
enhanced security and encryption features.
For information about this process, see Add an S2-encrypted Z-Wave device.
As an S0 device:
If the Z-Wave controller is not SmartStart or S2-compatible, this device can be enrolled in the traditional way as an S0
device.
1. Place the Z-Wave controller into Add mode.
2. Remove the battery tab from the sensor. When the LED on the sensor turns solid, the sensor has been
successfully added.
Note: If the battery tab has previously been removed, slide the device open to enroll the sensor. When the LED on
the sensor turns solid, the sensor has been successfully added.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Thermostats/Alarm.com_Temperature_Sensors/Alarm.c…
Updated: Wed, 04 Oct 2023 19:21:41 GMT
1
To delete the Alarm.com Temperature Sensor (ADC-S40-T)
1. Place the Z-Wave controller into Delete Mode.
2. Slide the device open to delete the sensor from the network. The LED on the sensor will turn solid and then blink
to indicate the device has been successfully deleted.
To reset the Alarm.com Temperature Sensor (ADC-S40-T)
Note: This will remove the device from the Z-Wave network.
1. Remove the battery door, tap the tamper switch three times in a row, press and hold the tamper switch for 10
seconds until the LED starts flashing. Then, release to reset to default.
2. After the tamper switch is released, the LED will blink quickly and then turn solid for 3 seconds indicating that the
device is resetting.
Troubleshooting
The Z-Wave device is not enrolling
If the Z-Wave device is unable to be enrolled following the instructions above, see Z-Wave device is not enrolling.
The Z-Wave device is not functioning consistently
If the Z-Wave device is not responding to remote commands or experiencing other issues, see Z-Wave device is not
functioning consistently.
The Z-Wave device is in malfunction or offline
If the Z-Wave device is not communicating at all, see Z-Wave device is in malfunction or offline.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Thermostats/Alarm.com_Temperature_Sensors/Alarm.c…
Updated: Wed, 04 Oct 2023 19:21:41 GMT
2
/