2. Home
  3. Home security & automation
  4. Access cards
  5. Secura Key
  6. E*Tag
E*Tag

Secura Key E*Tag Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Secura Key E*Tag Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the Secura Key E*Tag?
    How do I install the Secura Key E*Tag?
    What are the different models of the Secura Key E*Tag?
    What are the specifications of the Secura Key E*Tag?
    What are the ISO protocols supported by the Secura Key E*Tag?
    What types of cards are compatible with the Secura Key E*Tag?
    Does the Secura Key E*Tag have a status LED?
    Can I use an external antenna with the Secura Key E*Tag?
    What is the read range of the Secura Key E*Tag?
    What is the communications protocol used by the Secura Key E*Tag?
ET9-USB-1 Micro Reader
Installation Instructions
DIMENSIONS 2.7” X 0.9” X 0.4”
L x W x H (68.58 mm x 22.86 mm x 10.16 mm)
MOUNTING Install in standard USB jack
MATERIAL ABS
POWER REQUIREMENTS USB Port Power
ISO PROTOCOLS ISO 15693
CARD COMPATIBILITY Secura Key e*Tag
®
, TI HF-1, Philips I-Code SLI, ST Micro LRI,
Infineon My-D, My-D Lite
STATUS LED Internally mounted – view through translucent housing
EXTERNAL ANTENNA
(optional) 1” x 4” PCB with 11” MMCX cable, 5-6” read range
(25.4mm x 101.6MM PCB with 279.4mm cable,
127 – 152 mm read range)
EMI COMPLIANCE FCC Part 15-B Class B
READ RANGE 2-3” (50-75 mm)
Internal Antenna
COMMUNICATIONS PROTOCOL e*Tag® Host
FREQUENCY 13.56 MHz
ENVIRONMENTAL Operating Temperature: 32°F to +158° F (0°C to +70°C)
Relative Humidity: 0-95% Non-Condensing
WARRANTY
These Secura Key products are warranted against defects in materials and workmanship for two
years. Secura Key will replace any Secura Key manufactured product that fails to perform as
intended. This warranty does not include freight, taxes, duties, or installation expenses. See www.
securakey.com for complete terms and conditions.
SPECIFICATIONS:
Install in standard USB jack
The ET9-USB reader is available in three model variations
• ET9-USB-1 – switchable for internal or external antenna
• ET9-USB-1E – external antenna only; no switch
• ET9-USB-1I –internal antenna only; no switch, no MMCX jack
ET9-USB-1 Micro Reader
Installation Instructions
DIMENSIONS 2.7” X 0.9” X 0.4”
L x W x H (68.58 mm x 22.86 mm x 10.16 mm)
MOUNTING Install in standard USB jack
MATERIAL ABS
POWER REQUIREMENTS USB Port Power
ISO PROTOCOLS ISO 15693
CARD COMPATIBILITY Secura Key e*Tag
®
, TI HF-1, Philips I-Code SLI, ST Micro LRI,
Infineon My-D, My-D Lite
STATUS LED Internally mounted – view through translucent housing
EXTERNAL ANTENNA
(optional) 1” x 4” PCB with 11” MMCX cable, 5-6” read range
(25.4mm x 101.6MM PCB with 279.4mm cable,
127 – 152 mm read range)
EMI COMPLIANCE FCC Part 15-B Class B
READ RANGE 2-3” (50-75 mm)
Internal Antenna
COMMUNICATIONS PROTOCOL e*Tag® Host
FREQUENCY 13.56 MHz
ENVIRONMENTAL Operating Temperature: 32°F to +158° F (0°C to +70°C)
Relative Humidity: 0-95% Non-Condensing
WARRANTY
These Secura Key products are warranted against defects in materials and workmanship for two
years. Secura Key will replace any Secura Key manufactured product that fails to perform as
intended. This warranty does not include freight, taxes, duties, or installation expenses. See www.
securakey.com for complete terms and conditions.
SPECIFICATIONS:
Install in standard USB jack
The ET9-USB reader is available in three model variations
• ET9-USB-1 – switchable for internal or external antenna
• ET9-USB-1E – external antenna only; no switch
• ET9-USB-1I –internal antenna only; no switch, no MMCX jack
20301 Nordhoff Street Chatsworth, CA 91311
phone 818-882-0020 fax 818-882-7052
TOLL-FREE (800) 891-0020
E-mail: mail@securakey.com
Web site: www.securakey.com
INSTRUCTION TO THE USER
FCC ID: NNHETAGS9
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more or the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet of a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user
is cautioned that changes and modifications made to the equipment without the approval
of the manufacturer could void the user’s authority to operate this equipment.
RoHS
3059349
3322182 7267
20301 Nordhoff Street Chatsworth, CA 91311
phone 818-882-0020 fax 818-882-7052
TOLL-FREE (800) 891-0020
E-mail: mail@securakey.com
Web site: www.securakey.com
INSTRUCTION TO THE USER
FCC ID: NNHETAGS9
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more or the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet of a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user
is cautioned that changes and modifications made to the equipment without the approval
of the manufacturer could void the user’s authority to operate this equipment.
RoHS
3059349
3322182 7267
/