Secura Key E*Tag Installation guide

E*Tag
Secura Key
Brand
Secura Key
Model
E*Tag
Category
Access cards
Type
Installation guide

Secura Key ETag is a versatile device that offers convenient and reliable contactless smart card reading capabilities. Designed for ease of use, simply install it in a standard USB jack and it's ready to go. With its ability to read various ISO 15693 compatible cards, including Secura Key eTag®, TI HF-1, Philips I-Code SLI, ST Micro LRI, Infineon My-D, and My-D Lite, it provides compatibility with a wide range of applications. Additionally, the E*Tag boasts a compact design, making it portable and suitable for various use cases where contactless smart card reading is required.

Secura Key ETag is a versatile device that offers convenient and reliable contactless smart card reading capabilities. Designed for ease of use, simply install it in a standard USB jack and it's ready to go. With its ability to read various ISO 15693 compatible cards, including Secura Key eTag®, TI HF-1, Philips I-Code SLI, ST Micro LRI, Infineon My-D, and My-D Lite, it provides compatibility with a wide range of applications. Additionally, the E*Tag boasts a compact design, making it portable and suitable for various use cases where contactless smart card reading is required.

ET9-USB-1 Micro Reader
Installation Instructions
DIMENSIONS 2.7” X 0.9” X 0.4”
L x W x H (68.58 mm x 22.86 mm x 10.16 mm)
MOUNTING Install in standard USB jack
MATERIAL ABS
POWER REQUIREMENTS USB Port Power
ISO PROTOCOLS ISO 15693
CARD COMPATIBILITY Secura Key e*Tag
®
, TI HF-1, Philips I-Code SLI, ST Micro LRI,
Infineon My-D, My-D Lite
STATUS LED Internally mounted – view through translucent housing
EXTERNAL ANTENNA
(optional) 1” x 4” PCB with 11” MMCX cable, 5-6” read range
(25.4mm x 101.6MM PCB with 279.4mm cable,
127 – 152 mm read range)
EMI COMPLIANCE FCC Part 15-B Class B
READ RANGE 2-3” (50-75 mm)
Internal Antenna
COMMUNICATIONS PROTOCOL e*Tag® Host
FREQUENCY 13.56 MHz
ENVIRONMENTAL Operating Temperature: 32°F to +158° F (0°C to +70°C)
Relative Humidity: 0-95% Non-Condensing
WARRANTY
These Secura Key products are warranted against defects in materials and workmanship for two
years. Secura Key will replace any Secura Key manufactured product that fails to perform as
intended. This warranty does not include freight, taxes, duties, or installation expenses. See www.
securakey.com for complete terms and conditions.
SPECIFICATIONS:
Install in standard USB jack
The ET9-USB reader is available in three model variations
• ET9-USB-1 – switchable for internal or external antenna
• ET9-USB-1E – external antenna only; no switch
• ET9-USB-1I –internal antenna only; no switch, no MMCX jack
ET9-USB-1 Micro Reader
Installation Instructions
DIMENSIONS 2.7” X 0.9” X 0.4”
L x W x H (68.58 mm x 22.86 mm x 10.16 mm)
MOUNTING Install in standard USB jack
MATERIAL ABS
POWER REQUIREMENTS USB Port Power
ISO PROTOCOLS ISO 15693
CARD COMPATIBILITY Secura Key e*Tag
®
, TI HF-1, Philips I-Code SLI, ST Micro LRI,
Infineon My-D, My-D Lite
STATUS LED Internally mounted – view through translucent housing
EXTERNAL ANTENNA
(optional) 1” x 4” PCB with 11” MMCX cable, 5-6” read range
(25.4mm x 101.6MM PCB with 279.4mm cable,
127 – 152 mm read range)
EMI COMPLIANCE FCC Part 15-B Class B
READ RANGE 2-3” (50-75 mm)
Internal Antenna
COMMUNICATIONS PROTOCOL e*Tag® Host
FREQUENCY 13.56 MHz
ENVIRONMENTAL Operating Temperature: 32°F to +158° F (0°C to +70°C)
Relative Humidity: 0-95% Non-Condensing
WARRANTY
These Secura Key products are warranted against defects in materials and workmanship for two
years. Secura Key will replace any Secura Key manufactured product that fails to perform as
intended. This warranty does not include freight, taxes, duties, or installation expenses. See www.
securakey.com for complete terms and conditions.
SPECIFICATIONS:
Install in standard USB jack
The ET9-USB reader is available in three model variations
• ET9-USB-1 – switchable for internal or external antenna
• ET9-USB-1E – external antenna only; no switch
• ET9-USB-1I –internal antenna only; no switch, no MMCX jack
20301 Nordhoff Street Chatsworth, CA 91311
phone 818-882-0020 fax 818-882-7052
TOLL-FREE (800) 891-0020
E-mail: mail@securakey.com
Web site: www.securakey.com
INSTRUCTION TO THE USER
FCC ID: NNHETAGS9
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more or the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet of a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user
is cautioned that changes and modifications made to the equipment without the approval
of the manufacturer could void the user’s authority to operate this equipment.
RoHS
3059349
3322182 7267
20301 Nordhoff Street Chatsworth, CA 91311
phone 818-882-0020 fax 818-882-7052
TOLL-FREE (800) 891-0020
E-mail: mail@securakey.com
Web site: www.securakey.com
INSTRUCTION TO THE USER
FCC ID: NNHETAGS9
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more or the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet of a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-approved equipment or
unshielded cables is likely to result in interference to radio and TV reception. The user
is cautioned that changes and modifications made to the equipment without the approval
of the manufacturer could void the user’s authority to operate this equipment.
RoHS
3059349
3322182 7267
  • Page 1 1
  • Page 2 2

Secura Key E*Tag Installation guide

E*Tag
Secura Key
Brand
Secura Key
Model
E*Tag
Category
Access cards
Type
Installation guide

Secura Key ETag is a versatile device that offers convenient and reliable contactless smart card reading capabilities. Designed for ease of use, simply install it in a standard USB jack and it's ready to go. With its ability to read various ISO 15693 compatible cards, including Secura Key eTag®, TI HF-1, Philips I-Code SLI, ST Micro LRI, Infineon My-D, and My-D Lite, it provides compatibility with a wide range of applications. Additionally, the E*Tag boasts a compact design, making it portable and suitable for various use cases where contactless smart card reading is required.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents