Page is loading ...
DNZ1880YM
2MP, 30x D/N Explosion Proof
Integrated IP IR PTZ System
User Operations Manual
Model Number: DNZ1880YM2
Description: IP Explosion Proof, Integrated
IR PTZ Positioning System
2MP with 30x Optical Zoom
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
I
Quality
Quality Quality
Quality Assurance:
Assurance:Assurance:
Assurance:
When DNA1880YM2 is in warranty period, we offer free maintenance. Other
causes will be treated accordingly:
If User does not follow manual instruction, may damage product;
Open device without permission, may damage product;
Lightning strike or natural disaster;
If user has other agreement with our company, we will follow the
agreement letter.
Safety Assurance
Safety AssuranceSafety Assurance
Safety Assurance
The operation of device meets two conditions：
Its operation will not cause any interference.
Its operation will not be effected by outer interference, even if bad
interference.
Cautions
CautionsCautions
Cautions
Do not disassemble device. In case, it may cause water leakage,
electric leakage. Please follow the manual to do operation.
Please make sure the device working pressure, temperature, humidity
follow 1.6 items requirement.
Please use required power supply for device.
Please finish Inner and outside ground connection.
Please make sure installation site has stable support for device
operation.
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
II
The safe application period can last for years, from the date of production.
Each device has series number as production date, which can find on its
nameplate.
Please do operation after knowing well about device, safe cautions and
instruction.
1.
1. 1.
1.
Installation cautions
Installation cautionsInstallation cautions
Installation cautions
Do not do maintenance before cutting off its power supply.
Do not open the device, otherwise it may allow smoke, dust, high
temperature, moisture condensation into the product. In such cases, it
will affect camera image.
Please follow the cable connection instructions.
During maintenance, please protect the flameproof joint. And keep inside
area without metal dust or other particles.
Do not disassemble or rebuild the device.
2. Installation safety rules
2. Installation safety rules2. Installation safety rules
2. Installation safety rules
Do follow installation area safety rules.
When the equipment has problem, please stop operating it until the
problem is solved by tech support.
When come across bad weather, please check and fix all safety prevention
equipment.
Clear up ice, frog, rain, and snow on the device.
Installation site needs warning line/label.
When working at heights, unit should be carried out by suitably trained
personnel.
3. Power rules
3. Power rules3. Power rules
3. Power rules
During installation, please follow local electric safety standards
requirement.
User shall choose emergency power off device.
Please follow our cable connection instruction before operation.
The device has flame proof specification, please make cable thread by
explosion proof tube or pipeline.
SAFETY
SAFETY SAFETY
SAFETY
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
III
4. Ambient rules
4. Ambient rules4. Ambient rules
4. Ambient rules
Do not let the camera face to strong lights (lamps, sun). It will reduce
camera CCD or CMOS time of operation.
Do not leave the device on humid area, or temperature above 60℃ or less
than -40℃.
Do not allow water or conducting liquid to leak into device, it will
cause damage.
Keep the device in ventilated area.
The device must not be allowed to have great pressure, shaking, and shock
during delivery, storage and installation.
For protection, keep the package same or similar before delivery.
Suggest connect the device with surge protection equipment.
Finish Inner and outer ground connection.
5. Operation and maintenance rules
5. Operation and maintenance rules5. Operation and maintenance rules
5. Operation and maintenance rules
Do not disassemble device.
If CCD or CMOS has some dust or dirt, please use soft blower, or use
dustless cloth, lens wiping paper and dustless paper.
If device enclosure surface has dirt, please use neutral detergent.
Installation or maintenance of this device shall be carried out by
suitably trained personnel.
Please keep the CCD or CMOS away from the laser lights. Otherwise, sensor
will be damaged.
6. Environmental rules
6. Environmental rules6. Environmental rules
6. Environmental rules
Our device contains PCB board, electronics, plastics and grease. During
maintenance or scrap, please keep these under collection or control.
Statement
StatementStatement
Statement
The manual is just for reference.
It may have differences after the device upgrade.
Please contact with Dante Security to get the latest version.
We have checked the manual before releasing. We reserve rights to change
its content without prior notice.
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
IV
Explosion proof structure description
Explosion proof structure descriptionExplosion proof structure description
Explosion proof structure description
The device will not cause external blast even if explosive gas mixture
enters in product inner chamber. Unit is assembled with thick cover,
joint width, length, max and its surface temperature into consideration
before design, so as to guarantee its explosion proof character.
All fasteners adopt stainless steel or electroplated steel.
Elastic O-ring seal can resist heat and cold test.
Its enclosure can bear GB3638.2-2010 required water pressure test.
Test pressure is 2.0MPa, last for more than 10s, and product does not
show permanent deformation or damage.
During normal operation, its enclosure max surface temperature is less
than 80℃.
The device can bear GB/T2423.5-1995 required anti-shock test.
Glass window of unit housing, can bear GB3836.1-2010 required
anti-shock test and heat upheaval rest.
Its enclosure can reach to IP68 rated.
The devices have inner and outer ground connection, and are well marked.
During open the device, please protect the flame proof joint, in case
effect its flameproof functions.
B: Threaded flame proof joint
A: Spigot flame proof joint
A
A
B
B
A
A
B
B
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
V
Power off: use hands to transport it from bottom or both ends. Do not
transport by camera and lights housing, or pull cable.
When power is on: do not transport, open unit, or pull cables.
T
TT
Transporting Unit
ransporting Unitransporting Unit
ransporting Unit
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
VI
Content
ContentContent
Content
1. Preamble ................................................................................................................... 7
1.1 Specification .................................................. Error! Bookmark not defined.
1.2 Features .......................................................... Error! Bookmark not defined.
1.3 Range of application ....................................................................................... 7
1.4 Mechanical ..................................................... Error! Bookmark not defined.
1.5 Electrical ........................................................ Error! Bookmark not defined.
1.6 Operation ambient ........................................................................................... 9
1.7 Electric Safety (Standard test under the condition of atmosphere) ................. 9
2.Installation and debugging .......................................................................................... 10
2.1 Cautions before installation .......................................................................... 10
2.2 Cable connection ........................................................................................... 11
2.3 Fix bracket .................................................................................................... 13
2.4 Fix device and connection............................................................................. 14
2.5 Debugging ...................................................... Error! Bookmark not defined.
3. Trouble Removal ....................................................................................................... 19
4. Transport, storage, maintenance ............................................................................. 20
4.1 Transportation ................................................ Error! Bookmark not defined.
4.2 Storage ........................................................... Error! Bookmark not defined.
4.3 Maintenance ................................................................................................ 20
5. Statement ................................................................................................................... 20
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
7
1.
1. 1.
1. I
II
Introduction
ntroductionntroduction
ntroduction
Thanks for purchasing our products. DNA1880YM2 are explosion proof PTZ camera
with IR lights, which can be installed in areas of volatile gas and flammable powder,
such as hydrogen and hydrocarbon gas in the plants, chemical factory, and offshore
platforms.
The device strictly following standards: GB3836.1-2010 Electrical apparatus for
explosive gas atmospheres- part 1: General requirements; GB3836.2-2010 Electrical
Apparatus for explosive gas atmospheres-part 2: Flameproof enclosure d;
GB12476.5-2013 Electrical apparatus for use in the presence of combustible dust -part
1: General requirements;GB12476.5-2013 Electrical apparatus for use in the presence
of combustible dust -part 5: Protection by enclosure “tD”. The device is widely applied
for petrol, chemical, wharf, non-coal mining, aviation, military, and grain industry.
1.1 Specifications
1.1 Specifications1.1 Specifications
1.1 Specifications
PLEASE SEE LATEST DATA SHEET FOR COMPLETE SPECIFICATIONS
1.2 Features
1.2 Features1.2 Features
1.2 Features
The device is an integrated system with camera, pan, tilt, wiper, lights.
The device support different protocol and communication rates, so as to apply for various
requirements. Our device support wide voltage input. The enclosure includes IP Zoom camera,
and it is also equipped with surge protection device.
The device can auto pan 360 degree, vertical ±90° degree.
1.3 Range
1.3 Range1.3 Range
1.3 Range
of application
of applicationof application
of applications
ss
s
The device is fit for gas zone I, II; dust zone A21~A22.
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
8
1.4 Mechanical
1.4 Mechanical1.4 Mechanical
1.4 Mechanical
Material Stainless steel 316L sprayed with anti-corrosive paint
Optional Auto heating when less than 15℃(±5℃), it will operated on auto
Horizontal rotation 0~360°continuous, max 40°/s
Vertical rotation 0～±90°, Max 30°/s
Return trip horizontal, vertical less than 1.2 degree
Net weight 29.5kg
Gross weight 32kg
Fig 1.4.1 overall dimension
Fig 1.4.2 bottom mounting hole
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
9
1.5 Electrical
1.5 Electrical1.5 Electrical
1.5 Electrical
Voltage, current AC220V (AC85-265V)
less than 1A or AC24V less than 3A
Power ≤75W
Cable connection Integrated cable
Communication RS-485
Control communication Rate 2400~19200bps
Protocol PELCO-D
Preset 128, accuracy≤0.1°
Cruise 4-cruise team, each team has 16 cruise, stop by 30s.
Wiper wipe speed (30±10) Times per min
Light distance 50-100m
(when ambient less than 10lux, light auto start)
Ethernet interface full duplex TCP/IP protocol Ethernet signal
Audio (optional) 1- audio input, 1-audio output
Alarm (optional) 2-alarm input, 1-alarm output
Address code 0/1
1.6 Operation
1.6 Operation1.6 Operation
1.6 Operation
ambient
ambientambient
ambient
Air pressure 80-106KPa
Ambient temperature -50℃ ～ +60℃
Relative humidity Less than 95 %RH （+25℃）
1.7 Electric
1.7 Electric1.7 Electric
1.7 Electric
Safety (Standard test under the condition of atmosphere)
Safety (Standard test under the condition of atmosphere)Safety (Standard test under the condition of atmosphere)
Safety (Standard test under the condition of atmosphere)
Insulation resistance: The insulation resistant between cable connector and product
cover cannot less than 50MΩ, like and power entry cable connector, or control cable
connector.
Power frequency withstand voltage test: the power entry cable connector and product
crust can resist 50Hz, 1500V frequency& voltage, last for 1min. The control cable
connector and product outer housing can resist 50Hz, 5000V test for 1 minute.
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
10
2. Installation
2. Installation2. Installation
2. Installation
and
and and
and D
DD
Debugging
ebuggingebugging
ebugging
2.1 Precautions
2.1 Precautions2.1 Precautions
2.1 Precautions
before installation
before installationbefore installation
before installation
The device has been tested and placed under burn-in controls for 48 hours before
delivery. Included in test are camera housing and pan tilt station after full assembly.
Do not disassemble unit, otherwise it may cause damage.
Do not open the device in explosive area, even if its power has cut off.
Check during unpacking
Check during unpackingCheck during unpacking
Check during unpacking
DNA1880YM2 device, 1set
Sun-shield, 2 sets
5 sets M6*40 screw, washer, nuts.
M4, M6 socket head wrench, each 1set
Option 1： sealing ring, 1sets
Washer, 1sets
Option 2：screwed plug, 1set
explosion proof cable gland, 1set
Required tools for installation
Required tools for installationRequired tools for installation
Required tools for installation
1. Philips screwdriver 6*150
2. Wrench 300*36
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
11
W
WW
Warnings
arningsarnings
arnings
before installation
before installationbefore installation
before installation
Do not disassemble device, and follow manual instruction.
Please make cable connection as 1.5 items required.
Please make sure the device working pressure, temperature, humidity follow 1.6
items requirement.
Make connections and tests in the laboratory before carrying out installation on site.
The device cannot load other equipment, otherwise will cause damage.
2.2 Cable
2.2 Cable2.2 Cable
2.2 Cable
connection
connectionconnection
connection
2.2.1 Use
2.2.1 Use2.2.1 Use
2.2.1 Use
Explosion proof flexibility tube
Explosion proof flexibility tube Explosion proof flexibility tube
Explosion proof flexibility tube
Scrip cable outer layer as required length. Thread all components on the cable, as
Fig 2.2.1.1 showed below. (The connector has welded on the device end thread hole.
It is filled with explosion proof cement between the gland bushing and cables. After
cement is totally solidified, then it is allowed do assembling.)
coupling
elastomeric gasket
gland joint
O-ring
gland bushing
metal gasket
elastomeric
sealing ring
compression nut
e
x
p
l
o
s
i
o
n
p
r
o
t
e
c
t
e
d
f
l
e
x
i
b
l
e
c
o
n
d
u
i
t
cable inner layer
cable corer
cable outer layer
elastomeric
gasket
thread
Fig.2.2.1.1 explosion proof gland connection way
Follow Fig 2.2.1.2，fasten each component, and fix the set screw.
coupling
elastomeric
gasket
gland bushing
metal
gasket
set screw
elastomeric
sealing ring
compression
nut
e
x
p
l
o
s
i
o
n
p
r
o
t
e
c
t
e
d
f
l
e
x
i
b
l
e
c
o
n
d
u
i
t
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
12
Fig.2.2.1.2 Profile for connection
2.
2.2.
2.2
22
2.2
.2.2
.2
Armored cable
Armored cableArmored cable
Armored cable
Cut circled at 15mm distance from cable outer layer, and leave 15mm shielded
layer. Scrip armored cable outer layer as required length. Follow fig.2.2.2.1 showed,
thread each component. Press the 15mm shielded layer on the bushing 2 in negative
direction, and thread in bushing 1 （follow fig.2.2.2.2). Finally fasten each
component. (The connector has welded on the device end thread hole. After cement
is totally solidified, then it is allowed do assembling.)
Fig 2.2.2.1 armed cable connection way
Fig 2.2.2.2 shielded layer fasten way
Fasten explosion proof gland on the armed cable, as fig. 2.2.2.3 showed.
Fig 2.2.2.3 armed cable finish connection
Armored cable with explosion proof cable gland can be directly connected with all
explosion proof devices.
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
13
2.3 Installation
2.3 Installation2.3 Installation
2.3 Installation
optional
optionaloptional
optional
bracket
bracketbracket
bracket
In order to avoid excessive shaking from panning and tilting, it is best to install at top of
pole.
The user should choose the proper fastener to avoid of falling, rusting or damage.
2.
2.2.
2.3
33
3.
..
.1
11
1
Fix br
Fix brFix br
Fix bracket
acket acket
acket
Choose the proper position on wall for bracket. Fix camera on wall bracket in right
surveillance angle. Finally, choose qualified anchor bolt or expansion screw to fix
bracket on wall. Explosion proof junction box is installed at position, where is easy to
maintenance, as fig 2.3.1.1 showed. Cable is thread from trucking to junction box.
Wall mounted bracket fig 2.3.1.2; 2.3.1.3; 2.3.1.4.
bracket
wall
explosion proof
junction box
trunking or
cable bridge
Fig 2.3.1.1 wall bracket fix way Fig 2.3.1.2 wall bracket fix hole
Fig 2.3.1.3 wall bracket front view
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
14
Fig 2.3.1.4 wall bracket side view
2.4 Support
2.4 Support2.4 Support
2.4 Support
d
dd
device and connection
evice and connectionevice and connection
evice and connection
In consideration of explosion proof device will be installed at hazardous area,
please make connections and tests in the laboratory before carrying out
installation on site.
2.4.1
2.4.12.4.1
2.4.1
Installation instruction
Installation instructionInstallation instruction
Installation instruction
Camera cable should thread to explosion proof flexible tube (or choose armed cable),
and then connect to explosion
proof junction box. From the
explosion proof junction box to
control room, the cable should
thread by metal pipeline
(galvanized steel pipeline). Or you
can choose armed cable directly to
control room, as fig 2.4.1 showed.
Fig 2.4.1 camera installation way
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
15
2.5 Debugging
2.5 Debugging2.5 Debugging
2.5 Debugging
2.5.1 System
2.5.1 System2.5.1 System
2.5.1 System
connection
connectionconnection
connections
ss
s
Fig 2.5.1 system connection way
Network camera can be connected with LAN or WAN, user can do surveillance or
record by internet.
Analog camera can be connected with explosion proof keyboard and explosion proof
control box. From the explosion proof monitor, user can get site view.
2.5.2 Cab
2.5.2 Cab2.5.2 Cab
2.5.2 Cable
lele
le
definition
definitiondefinition
definitions
ss
s
The device cable output is above 2m length. The provided cable must be joined in
junction box with system integrated cable. Define as follow:
Sheet 2.5.2 cable definition
Name Color Description
Alarm, audio
purple audio output
black audio grounded
purple white audio input
Laptop
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
16
2.5.3 Settings
2.5.3 Settings2.5.3 Settings
2.5.3 Settings
Use F-wrench to open camera end flange, you will see the code switch, as fig 2.5.3.1
showed.
Fig 2.5.3.1 code switch
There are total 255 address, and address 1-65 as sheet 2.5.3.1.
Sheet 2.5.3.1 address set
Address
Code
1 2 3 4 5 6 7 8
1 ON OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF
4 OFF OFF ON OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF
blue white alarm input 1
blue alarm input 2
black white alarm input grounded
orange Alarm output1
orange white Alarm output 1
MB network Unshielded twisted pair (UTP)
Power
thick brown (L)
AC24V
±10%
thick blue (N)
thick yellow green (G) Grounded
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
17
... ...
... ...
... ...
124 OFF OFF ON ON ON ON ON OFF
125 ON OFF ON ON ON ON ON OFF
126 OFF ON ON ON ON ON ON OFF
127 ON ON ON ON ON ON ON OFF
128 OFF OFF OFF OFF OFF OFF OFF ON
... ...
255 ON ON ON ON ON ON ON ON
The 1-2 of switch code is for baud rate, Baud rate set as sheet 2.5.3.2.
sheet 2.5.3.2:
Switch code
Baud rate（bps）
1 2
OFF OFF 2400
ON OFF 4800
OFF ON 9600
ON ON 19200
The 3-5of switch code is for protocol, as sheet 2.5.3.3.
Sheet 2.5.3.3：
Switch code
Protocol
3 4 5
OFF OFF OFF PELCO-D
ON OFF OFF PELCO-P
ON ON ON USER
Remarks: User is some user required special protocol
The 6-8 of switch code is for camera set, as sheet 2.5.3.4.
Sheet 2.5.3.4：
Switch code
Camera
6 7 8
OFF OFF OFF SONY
ON OFF OFF HITACHI
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
18
OFF ON OFF SAMSUNG SCC-4223P
ON ON OFF LG
OFF OFF ON SHILIN
ON OFF ON Support PELCO-D Camera
OFF ON ON SAMSUNG
ON ON ON SANYO
Remarks: customer can offer required camera type
2.5.4
2.5.4 2.5.4
2.5.4 check before power supply
check before power supplycheck before power supply
check before power supply
Check power cable, network cable connection is in right way, and code settings
according to above.
2.5.5
2.5.5 2.5.5
2.5.5 Check during power supply
Check during power supplyCheck during power supply
Check during power supply
When camera connect with power, it will auto finish self-operation.
2.5.6
2.5.6 2.5.6
2.5.6 Camera set, accessing by web browsers, client software
Camera set, accessing by web browsers, client softwareCamera set, accessing by web browsers, client software
Camera set, accessing by web browsers, client software
As for setting IP camera or access camera by web browser, client software, please
follow camera manufacturer manual in next section of User Manual.
2.5.6 Camera login
2.5.6 Camera login2.5.6 Camera login
2.5.6 Camera login
User: admin
Password: admin
DNA1880YM2 EXPLOSION PROOF INFRARED PTZ CAMERA·MANUAL
19
2.5.7 Wiper and infrared lights
2.5.7 Wiper and infrared lights 2.5.7 Wiper and infrared lights
2.5.7 Wiper and infrared lights manual
manual manual
manual control
controlcontrol
controls
ss
s
Assistant 1 is to control wiper, AUX On, wiper work; AUX off, Wiper stop.
Assistant 2 is to control lights. AUX On, lights manual on, AUX off, lights manual off.
(Lights defaults as auto on and off according to light resistor. Lights defaults as auto
mode, if no operation in PTZ function in 10 minutes.)
3. Trouble Removal
3. Trouble Removal3. Trouble Removal
3. Trouble Removal
FAULT REASON SOLUTIONS
No image
power cut off check power supply
Video cable loose connection check video cable connection
camera cannot
auto switch to
B&W during
night
It may has highlight;
Color to B&W switch has set as
manual.
To avoid has highlight among camera view.
Set auto switch of color to B&W.
Image not clear
Zoom auto focus has off
Window glass has dust, dirty stuff
Make zoom auto focus
Clean window glass
Image appear
sometimes
Video cable loose connection Check video cable connection
Signal cable not in right
connection way
Check signal cable in right connection
Communication distance is too
long
Add repeater to extend communication
distance
Wrong address
Follow manual, do the right set
Wrong protocol
Wrong baud rate
Cannot control
camera
Wrong camera set
Wrong control way (SW2)
/