Grizzly W1854 Owner's manual

Model W1854

***IMPORTANT UPDATE***

Applies to Models Mfd. Since 7/19

and Owner's Manual Revised 12/18

Phone #: (360) 734-3482 • Tech Support: techsupport@woodstockint.com • Web: www.woodstockint.com

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

Printed in China#20604MN

We made the following changes to this machine since the manual was printed:

• New parts have been added.

Aside from the information contained in this update, all other content in the owner's manual is

applicable and MUST be read and understood for your own safety.

IMPORTANT: Keep this update with the owner's manual for future reference. If you have any further

questions, contact our Technical Support.

READ THIS FIRST

54

123

4

152

153

160

129

125

124

100

149

164

163

162

161

42

33

147

148

43

47

88

155

150

117

154

59

79

156

74

152

71V2

151

REF PART # DESCRIPTION REF PART # DESCRIPTION

71V2 X1854071V2 DRIVE PULLEY V2.07.19 154 X1854154 COLLAR

117 X1854117 HEX NUT M5-.8 155 X1854155 SET SCREW M6-1 X 6

147 X1854147 CAP SCREW M6-1 X 20 156 X1854156 FLAT WASHER 5MM

148 X1854148 FLAT WASHER 6MM 160 X1854160 SCREW

149 X1854149 SET SCREW M8-1.25 X 20 161 X1854161 KEY 4 X 4 X 8

150 X1854150 HEX BOLT M5-.8 X 25 162 X1854162 SET SCREW M4-.7 X 8

151 X1854151 CAP SCREW M8-1.25 X 16 163 X1854163 RUBBER CUSHION

152 X1854152 SET SCREW M8-1.25 X 10 164 X1854164 BUSHING

153 X1854153 FLAT WASHER 3MM

New Parts & Parts List

OWNER'S MANUAL

(FOR MODELS MANUFACTURED SINCE 04/18)

MODEL W1854

18" OPEN-END DRUM SANDER

Phone: (360) 734-3482 • Online Technical Support: [email protected]

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

#19084KBJHAB Printed in China

3092372

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property

damage from negligence, improper training, machine modifications or

misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

SETUPELECTRICAL MAINTENANCE

SERVICE PARTS

OPERATIONS

SAFETYINTRODUCTION

USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!

INTRODUCTION .....................................2

Woodstock Technical Support .................. 2

Machine Specifications .......................... 3

Controls & Features ............................. 5

SAFETY ...............................................6

Standard Machinery Safety Instructions ...... 6

Additional Safety for Sanders .................. 8

ELECTRICAL .........................................9

Circuit Requirements ............................ 9

Grounding Requirements ...................... 10

Extension Cords ................................ 10

SETUP .............................................. 11

Unpacking ....................................... 11

Items Needed for Setup ....................... 11

Hardware Recognition Chart ................. 12

Inventory ........................................ 13

Machine Placement ............................ 14

Assembly ......................................... 15

Dust Collection ................................. 18

Test Run .... ...................................... 19

Recommended Adjustments .................. 19

OPERATIONS....................................... 20

General .......................................... 20

Stock Inspection & Requirements ........... 21

Setting Depth of Cut ........................... 22

Sanding .......................................... 23

Adjusting Conveyor Feed Rate ............... 23

Sanding Tips ..................................... 24

Choosing Sandpaper ........................... 24

Replacing Sandpaper........................... 25

Changing Sanding Drum Speeds .............. 27

ACCESSORIES ...................................... 28

Sander Accessories ............................. 28

MAINTENANCE .................................... 29

General .......................................... 29

Cleaning & Protecting ......................... 29

Lubrication ...................................... 30

Cleaning Sandpaper Belts ..................... 31

SERVICE ............................................ 32

General .......................................... 32

Replacing V-Belt ................................ 32

Tensioning V-Belt ............................... 33

Aligning Pulleys ................................. 34

Tracking Conveyor Belt ........................ 35

Tensioning Conveyor Belt ..................... 36

Replacing Conveyor Belt ...................... 37

Making Gauge Blocks .......................... 38

Aligning Drum ................................... 39

Aligning Pressure Rollers ...................... 40

Troubleshooting ................................. 42

Electrical Safety Instructions ................. 44

Wiring Diagram ................................. 45

PARTS .............................................. 46

Main Breakdown ................................ 46

Labels & Cosmetics ............................ 50

WARRANTY ........................................ 53

Contents

-2-

Model W1854 (For Machines Mfd. Since 04/18)

INTRODUCTION

Woodstock Technical Support

This machine has been specially designed to provide many years of trouble-free service. Close attention

to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.

Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to

include the basic information for safety, setup, operation, maintenance, and service of this product.

We stand behind our machines! In the event that questions arise about your machine, please contact

Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.

biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.

INTRODUCTION

If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.

If you have comments about this manual, please contact us at:

Woodstock International, Inc.

Attn: Technical Documentation Manager

P.O. Box 2309

Bellingham, WA 98227

Email: manuals@woodstockint.com

-3-

Model W1854 (For Machines Mfd. Since 04/18)

INTRODUCTION

Model W1854 Machine Specifications, Page 1 of 2

MODEL W1854

18" 1.5 HP OPENEND DRUM SANDER W/VARIABLESPEED FEED

Product Dimensions

Weight.......................................................................................................... 198 lbs.

Width (side‐to‐side) x Depth (front‐to‐back) x Height.............................. 35‐1/2 x 22‐1/2 x 50 in.

Footprint (Length x Width).................................................................... 41‐1/2 x 22‐1/2 in.

Shipping Dimensions

Type.................................................................................. Cardboard Box w/Wood Skids

Content........................................................................................................ Machine

Weight.......................................................................................................... 235 lbs.

Length x Width x Height........................................................................... 25 x 33 x 33 in.

Must Ship Upright.................................................................................................. Yes

Electrical

Power Requirement.................................................................... 120V, Single‐Phase, 60 Hz

Full‐Load Current Rating..................................................................................... 13.92A

Minimum Circuit Size............................................................................................. 20A

Connection Type......................................................................................... Cord & Plug

Power Cord Included.............................................................................................. Yes

Power Cord Length............................................................................................... 6 ft.

Power Cord Gauge............................................................................................ 14 AWG

Plug Included....................................................................................................... Yes

Included Plug Type............................................................................................... 5‐15

Switch Type............................................................ Paddle Safety Switch w/Removable Key

Motors

Conveyor Belt

Horsepower.............................................................................................. 1/8 HP

Amps....................................................................................................... 0.92A

Speed.................................................................................................. 1800 RPM

Type............................................................................................... Universal DC

Power Transfer ................................................................................... Direct Drive

Main

Horsepower.............................................................................................. 1.5 HP

Phase.............................................................................................. Single‐Phase

Amps.......................................................................................................... 13A

Speed.................................................................................................. 3450 RPM

Type.......................................................................... ODP Capacitor‐Start Induction

Power Transfer ................................................................................... V‐Belt Drive

Bearings............................................................... Shielded & Permanently Lubricated

-4-

Model W1854 (For Machines Mfd. Since 04/18)

INTRODUCTION

Model W1854 Machine Specifications, Page 2 of 2

Main Specifications

Operation Information

Number of Sanding Heads.................................................................................... 1

Maximum Board Width.................................................................................. 36 in.

Minimum Board Width.................................................................................... 1 in.

Maximum Board Thickness.......................................................................... 4‐1/2 in.

Minimum Board Thickness............................................................................. 1/8 in.

Minimum Board Length................................................................................... 6 in.

Sandpaper Speed............................................................................. 2600, 3400 FPM

Conveyor Feed Rate................................................................................ 0 ‐ 12 FPM

Sandpaper Length........................................................................................ 89 in.

Sandpaper Width.......................................................................................... 3 in.

Drum Information

Infeed Sanding Drum Type......................................................................... Aluminum

Infeed Sanding Drum Size................................................................................ 4 in.

Construction

Conveyor Belt....................................................................................... Sandpaper

Body......................................................................................................... Steel

Base......................................................................................................... Steel

Paint Type/Finish............................................................................. Powder Coated

Other Related Information

Floor To Table Height.............................................................................. 35 ‐ 40 in.

Sanding Belt Tension.......................................................................... Spring‐Loaded

Conveyor Belt Length.................................................................................... 45 in.

Conveyor Belt Width..................................................................................... 18 in.

Belt Roller Size....................................................................................... 1‐3/8 in.

Number of Dust Ports......................................................................................... 1

Dust Port Size.............................................................................................. 4 in.

Other

Country of Origin ............................................................................................... China

Warranty ....................................................................................................... 2 Years

Approximate Assembly & Setup Time ............................................................... 1‐1/2 Hours

Serial Number Location .................................................................................... ID Label

ISO 9001 Factory ................................................................................................... No

Certified by a Nationally Recognized Testing Laboratory (NRTL) ......................................... Yes

Features

Open‐Ended Design Accommodates Workpieces up to 36" Wide

Spring‐Loaded Sanding Belt Tension

Sandpaper Conveyor Belt

4" Dust Port

Electronic Variable‐Speed Conveyor Motor

4" Aluminum Sanding Drum

Durable Powder‐Coated Finish

Stationary Drum Headstock

Paddle Switch with Removable Key

Easy Access for Sandpaper Changes

-5-

Model W1854 (For Machines Mfd. Since 04/18)

INTRODUCTION

Become familiar with the names and locations of the controls and features shown below to better

understand the instructions in this manual.

A. Conveyor Feed Rate Dial: Rotate dial

clockwise to increase conveyor belt feed

rate or counterclockwise to decrease feed

rate. Conveyor feed rate ranges from 0–12

FPM.

B. ON/OFF Paddle Switch w/Disabling Key:

Turns motor ON and OFF. Remove yellow

key to disable switch.

C. Circuit Breaker: Trips during excessive

sanding operation when workload overloads

circuit. Press button to reset breaker.

D. Table Height Indicator: Displays

approximate distance between sanding

drum and conveyor belt.

E. Dust Port: Connects sander to 4" dust

collection system.

F. Table Elevation Handwheel: Raises

and lowers conveyor table (G). Rotate

counterclockwise to lower table; rotate

clockwise to raise table. One full rotation

moves the table approximately 0.060"

(

1

⁄16").

G. Conveyor Table w/Belt: Feeds workpiece

across conveyor table during sanding

operations.

H. Belt Access Panel: Remove panel to change

sanding belt pulley positions or make belt

adjustments.

I. Conveyor Belt Motor: Controls feed rate of

conveyor belt. Use Conveyor Feed Rate Dial

(C) to adjust feed speed.

Controls & Features

D

F

I

G

C

B

A

E

H

-6-

Model W1854 (For Machines Mfd. Since 04/18)

SAFETY

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

This symbol is used to alert the user to useful information about

proper operation of the equipment or a situation that may cause

damage to the machinery.

NOTICE

SAFETY

OWNER’S MANUAL.

Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY.

Untrained operators

have a higher risk of being hurt or killed. Only

allow trained/supervised people to use this

machine. When machine is not being used,

disconnect power, remove switch keys, or

lock-out machine to prevent unauthorized

use—especially around children. Make

workshop kid proof!

DANGEROUS ENVIRONMENTS.

Do not use

machinery in areas that are wet, cluttered,

or have poor lighting. Operating machinery

in these areas greatly increases the risk of

accidents and injury.

MENTAL ALERTNESS REQUIRED.

Full mental

alertness is required for safe operation of

machinery. Never operate under the influence

of drugs or alcohol, when tired, or when

distracted.

ELECTRICAL EQUIPMENT INJURY RISKS. You can

be shocked, burned, or killed by touching live

electrical components or improperly grounded

machinery. To reduce this risk, only allow an

electrician or qualified service personnel to

do electrical installation or repair work, and

always disconnect power before accessing or

exposing electrical equipment.

DISCONNECT POWER FIRST. Always disconnect

machine from power supply BEFORE making

adjustments, changing tooling, or servicing

machine. This eliminates the risk of injury

from unintended startup or contact with live

electrical components.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating

or observing machinery to reduce the risk of

eye injury or blindness from flying particles.

Everyday eyeglasses are not approved safety

glasses.

Standard Machinery Safety Instructions

For Your Own Safety,

Read Manual Before Operating Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This

manual uses a series of symbols and signal words intended to convey the level of importance of the

safety messages. The progression of symbols is described below. Remember that safety messages by

themselves do not eliminate danger and are not a substitute for proper accident prevention mea-

sures—this responsibility is ultimately up to the operator!

SAFETY

Standard Machinery Safety Instructions

-7-

Model W1854 (For Machines Mfd. Since 04/18)

SAFETY

WEARING PROPER APPAREL. Do not wear

clothing, apparel, or jewelry that can become

entangled in moving parts. Always tie back

or cover long hair. Wear non-slip footwear to

avoid accidental slips, which could cause loss

of workpiece control.

HAZARDOUS

DUST. Dust created while using

machinery may cause cancer, birth defects,

or long-term respiratory damage. Be aware of

dust hazards associated with each workpiece

material, and always wear a NIOSH-approved

respirator to reduce your risk.

HEARING PROTECTION.

Always wear hearing

protection when operating or observing

loud machinery. Extended exposure to this

noise without hearing protection can cause

permanent hearing loss.

REMOVE ADJUSTING TOOLS.

Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys,

wrenches, or any other tools on machine.

Always verify removal before starting!

INTENDED USAGE.

Only use machine for its

intended purpose—never make modifications

without prior approval from Woodstock

International. Modifying machine or using

it differently than intended will void the

warranty and may result in malfunction or

mechanical failure that leads to serious

personal injury or death!

AWKWARD POSITIONS.

Keep proper footing and

balance at all times when operating machine.

Do not overreach! Avoid awkward hand

positions that make workpiece control difficult

or increase the risk of accidental injury.

CHILDREN & BYSTANDERS.

Keep children and

bystanders at a safe distance from the work

area. Stop using machine if they become a

distraction.

GUARDS & COVERS.

Guards and covers reduce

accidental contact with moving parts or flying

debris—make sure they are properly installed,

undamaged, and working correctly.

FORCING MACHINERY. Do not force machine. It

will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury may

occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement during

operation greatly increases risk of injury or

loss of control. Before starting, verify machine

is stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for

recommended accessories. Using improper

accessories will increase risk of serious injury.

UNATTENDED OPERATION. To reduce the risk

of accidental injury, turn machine OFF and

ensure all moving parts completely stop

before walking away. Never leave machine

running while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to

keep machine in good working condition. A

machine that is improperly maintained could

malfunction, leading to serious personal injury

or death.

CHECK DAMAGED PARTS. Regularly inspect

machine for any condition that may affect

safe operation. Immediately repair or replace

damaged or mis-adjusted parts before

operating machine.

MAINTAIN POWER CORDS. When disconnecting

cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the

cord may damage the wires inside, resulting

in a short. Do not handle cord/plug with wet

hands. Avoid cord damage by keeping it away

from heated surfaces, high traffic areas, harsh

chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the

intended operation, stop using the machine!

Contact Technical Support at (360) 734-3482.

-8-

Model W1854 (For Machines Mfd. Since 04/18)

SAFETY

Additional Safety for Sanders

Serious injury or death can occur if fingers, clothing, jewelry, or hair get entangled in moving

components. Impact injuries can occur from kickback if workpiece is improperly fed into moving

sandpaper. Serious pinch injuries can occur from touching in-running nip point between table and

sanding surface. Long-term respiratory damage can occur from using sander without proper use

of a respirator. To reduce the risk of these hazards, operator and bystanders MUST completely

heed the hazards and warnings below.

SANDPAPER CONDITION. Worn or damaged sand-

paper can aggressively grab workpiece, result-

ing in subsequent injuries from operator loss

of workpiece control. Always inspect sandpa-

per before operation and replace if worn or

damaged.

WORKPIECE SUPPORT & HAND PLACEMENT.

Rotating sandpaper can remove a large

amount of flesh quickly, and kickback can

occur with violent force if workpiece is not

properly supported during operation. Always

sand with workpiece firmly against table or

another support device. Never touch moving

sandpaper on purpose.

IN-RUNNING NIP POINTS. The gap between mov-

ing sandpaper and fixed table/support cre-

ates a pinch point for fingers or workpieces;

the larger this gap is, the greater the risk of

fingers or workpieces getting caught in it.

Minimize this risk by adjusting table/support to

no more than

1

⁄

16

" away from sandpaper. For

spindle sanders, always use the table insert

that fits closest diameter of installed drum.

MINIMUM STOCK DIMENSION. Small workpieces

can be aggressively pulled from your hands,

causing contact with sanding surface. Always

use a jig or other holding device when sanding

small workpieces, and keep hands and fingers

at least 2" away from sanding surface.

WORKPIECE INSPECTION. Nails, staples, knots,

or other imperfections in workpiece can be

dislodged and thrown from sander at a high

rate of speed at people, or cause damage to

sandpaper or sander. Never sand stock that

has embedded foreign objects or questionable

imperfections.

SANDPAPER DIRECTION. Feeding workpiece

incorrectly can cause it to be thrown from

machine, striking operator or bystanders, or

causing your hands to slip into the moving

sandpaper. To reduce these risks, only sand

against direction of sandpaper travel, ensure

workpiece is properly supported, and avoid

introducing sharp edges into moving sandpaper

on leading side of workpiece.

FEEDING WORKPIECE. Jamming workpiece into

sanding surface could cause it to be grabbed

aggressively, pulling hands into sanding sur-

face. Firmly grasp workpiece in both hands

and ease it into sandpaper using light pressure.

AVOIDING ENTANGLEMENT. Entanglment in mov-

ing parts can cause pinching and crushing inju-

ries. Keep all guards in place and closed. DO

NOT wear loose clothing, gloves, or jewelry,

and tie back long hair.

SANDING DUST. Sanding creates large amounts of

dust that can lead to eye injury or respiratory

illness. Reduce risk by wearing approved eye

and respiratory protection when using sander.

Never operate without adequate dust collec-

tion system in place and running. Dust collec-

tion is not a substitute for using a respirator.

WORKPIECE INTEGRITY. Sanding fragile work-

pieces can result in loss of control, resulting in

abrasion injuries, impact injuries, or damage

to sandpaper. Only sand solid workpieces that

can withstand power sanding forces. Make sure

workpiece shape is properly supported; avoid

sanding workpieces without flat bottom sur-

faces unless some type of jig is used to main-

tain support and control when sanding force is

applied.

-9-

Model W1854 (For Machines Mfd. Since 04/18)

ELECTRICAL

Circuit Requirements

This machine must be connected to the correct size and

type of power supply circuit, or fire or electrical damage

may occur. Read through this section to determine if an

adequate power supply circuit is available. If a correct

circuit is not available, a qualified electrician MUST install

one before you can connect the machine to power.

A power supply circuit includes all electrical equipment

between the breaker box or fuse panel in the building

and the machine. The power supply circuit used for

this machine must be sized to safely handle the full-

load current drawn from the machine for an extended

period of time. (If this machine is connected to a circuit

protected by fuses, use a time delay fuse marked D.)

Circuit Requirements for 120V

This machine is prewired to operate on a power supply

circuit that has a verified ground and meets the following

requirements:

Circuit Type ............... 110V/120V, 60 Hz, Single-Phase

Circuit Size ............................................. 20 Amps

Plug/Receptacle .................................... NEMA 5-15

Full-Load Current Rating

The full-load current rating is the amperage a machine

draws at 100% of the rated output power. On machines

with multiple motors, this is the amperage drawn by the

largest motor or sum of all motors and electrical devices

that might operate at one time during normal operations.

Full-Load Current Rating at 120V .............. 13.92 Amps

The machine must be properly set up

before it is safe to operate. DO NOT

connect this machine to the power

source until instrtucted to do so later

in this manual.

Incorrectly wiring or grounding this

machine can cause electrocution, fire,

or machine damage. To reduce this risk,

only an electrician or qualified service

personnel should do any required

electrical work on this machine.

NOTICE

The circuit requirements listed in this

manual apply to

a dedicated circuit—

where only one machine will be running

at a time. If this machine will be

connected to a shared circuit where

multiple machines will be running at the

same time, consult with an electrician

to ensure that the circuit is properly

sized for safe operation.

-10-

Model W1854 (For Machines Mfd. Since 04/18)

ELECTRICAL

Grounding Requirements

This machine MUST be grounded. In the event of certain

types of

malfunctions or breakdowns, grounding provides

a path of least resistance for electric current

to travel—in

order

to reduce the risk of electric shock.

Improper connection of the equipment-grounding

wire

will

increase

the risk of electric shock. The wire with green

insulation

(with/without yellow stripes) is the equipment-

grounding

wire. If repair or replacement of the power

cord or plug is necessary, do not connect the equipment-

grounding

wire to a live (current carrying) terminal.

Check with a qualified electrician or service personnel

if

you do not understand these grounding requirements,

or if

you are in doubt about whether the tool is

properly grounded.

If you ever notice that a cord or

plug is damaged or worn, disconnect it from power, and

immediately replace it with a new one.

Grounding Pin

Neutral Hot

5-15 PLUG

GROUNDED

5-15 RECEPTACLE

120V

Figure 1. NEMA 5-15 plug & receptacle.

DO NOT modify the provided plug or

use an adapter if the plug will not

fit the receptacle. Instead, have an

electrician install the proper receptacle

on a power supply circuit that meets

the requirements for this machine.

Extension Cords

We do not recommend using an extension cord with

this machine. Extension cords cause voltage drop, which

may damage electrical components and shorten motor

life. Voltage drop increases with longer extension cords

and smaller gauge sizes (higher gauge numbers indicate

smaller sizes).

Any extension cord used with this machine must contain a

ground wire, match the required

plug and receptacle, and

meet the following requirements:

Minimum Gauge Size at 120V ...................... 12 AWG

Maximum Length (Shorter is Better) ................50 ft.

For 120V Connection

This machine is equipped with a power cord with an

equipment-grounding

wire and NE M A 5-15 grounding

plug

(see figure). The plug must only be inserted into

a matching

receptacle that is properly installed and

grounded in accordance with local codes and ordinances.

-11-

Model W1854 (For Machines Mfd. Since 04/18)

SETUP

Unpacking

This machine has been carefully packaged for safe

transportation. If you notice the machine has been

damaged during shipping, please contact your authorized

Shop Fox dealer immediately.

Description Qty

• Additional People ..........................................2

• Safety Glasses ......................................... 1 Ea.

• Phillips Head Screwdriver #2 ............................1

• Wood Blocks 2x4 ...........................................3

• Wood Shims ..................................... As Needed

• Dust Hose 4" .......................... Length As Needed

• Hose Clamps 4" ............................................2

Items Needed for Setup

The following items are needed, but not included, to set

up your machine.

SUFFOCATION HAZARD!

Immediately discard all

plastic bags and packing

materials to eliminate

choking/suffocation

hazards for children and

animals.

USE helpers or power

lifting equipment to lift

this machine. Otherwise,

serious personal injury

may occur.

Wear safety glasses during

entire setup process!

This machine presents

serious injury hazards

to untrained users. Read

through this entire manual

to become familiar with

the controls and opera-

tions before starting the

machine!

-12-

Model W1854 (For Machines Mfd. Since 04/18)

SETUP

Hex

Wrench

16mm

MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE

7

⁄16"

3

⁄8"

1

⁄4"

5

⁄16"

#10

1

⁄2"

WASHERS ARE MEASURED BY THE INSIDE DIAMETER

USE THIS CHART TO IDENTIFY

HARDWARE DURING THE

INVENTORY/ASSEMBLY

PROCESS.

Flat Washer

Lock

Washer

Hex

Nut

Wing

Nut

Set

Screw

Cap

Screw

Carriage

Bolt

Hex

Bolt

Button

Head

Screw

Flange

Bolt

LINES ARE

1

⁄16" INCH APART

1

⁄4"

3

⁄8"

1

⁄2"

5

⁄8"

5

⁄16"

7

⁄16"

9

⁄16"

3

⁄4"

7

⁄8"

3

2

1

⁄4"

2

1

⁄2"

2

3

⁄4"

2

1

3

⁄4"

1

⁄2"

1

⁄4"

1

LINES ARE 1MM APART

5mm

10mm

20mm

15mm

25mm

40mm

30mm

35mm

45mm

50mm

60mm

55mm

70mm

65mm

75mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

5

⁄8"

W

A

S

H

E

R

D

I

A

M

E

T

E

R

9

⁄16"

1

⁄2"

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

12mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

10mm

7

⁄16"

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

8mm

3

⁄8"

W

A

S

H

E

R

D

I

A

M

E

T

E

R

5

⁄16"

W

A

S

H

E

R

D

I

A

M

E

T

E

R

1

⁄4"

W

A

S

H

E

R

D

I

A

M

E

T

E

R

#10

W

A

S

H

E

R

D

I

A

M

E

T

E

R

W

A

S

H

E

R

D

I

A

M

E

T

E

R

4mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

6mm

W

A

S

H

E

R

D

I

A

M

E

T

E

R

5mm

4mm

6mm

5mm

8mm

10mm

12mm

Tap

Screw

Phillips

Head

Screw

Flat

Head

Screw

E-Clip

External

Retaining

Ring

Internal

Retaining

Ring

Key

Lock

Nut

Hardware Recognition Chart

-13-

Model W1854 (For Machines Mfd. Since 04/18)

SETUP

Box Contents (Figure 2) Qty

A. Main Sander Unit (Not Shown) ..........................1

B. Top Long Brackets .........................................2

C. Top Short Brackets ........................................2

D. Bottom Short Brackets ....................................2

E. Bottom Long Brackets ....................................2

F. Stand Legs ..................................................4

G. Handwheel w/Handle .....................................1

H. Hardware and Tools (Not Shown)

— Hex Bolts M8-1.25 x 20 ................................4

— Hex Nuts M8-1.25 ......................................4

— Flat Washers 8mm ......................................8

— Carriage Bolts M8-1.25 x 15 ......................... 24

— Flange Nuts M8-1.25 ................................. 24

— Combination Wrench 8/12mm ........................1

— Hex Wrenches 4, 5, 6mm ........................1 Ea.

Inventory

The following is a list of items shipped with your machine.

Before beginning setup, lay these items out and inventory

them.

Note:

If you cannot find an item on this list, carefully

check around/inside the machine and packaging materials.

Often, these items get lost in packaging materials while

unpacking or they are pre-installed at the factory.

Figure 2. Additional box contents.

B

C

D

E

F

G

-14-

Model W1854 (For Machines Mfd. Since 04/18)

SETUP

Machine Placement

Weight Load

Refer to the

Machine Specifications for the

weight of your machine. Make sure that the

surface upon which the machine is placed will

bear the weight of the machine, additional

equipment that may be installed on the

machine, and the heaviest workpiece that will

be used. Additionally, consider the weight of

the operator and any dynamic loading that may

occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that

will be processed through this machine and

provide enough space around the machine

for adequate operator material handling or

the installation of auxiliary equipment. With

permanent installations, leave enough space

around the machine to open or remove doors/

covers as required by the maintenance and

service described in this manual.

See below for

required space allocation.

Physical Environment

The physical environment where your machine is

operated is important for safe operation and the

longevity of its components. For best results,

operate this machine in a dry environment

that is free from excessive moisture, hazardous

chemicals, airborne abrasives, or extreme

conditions. Extreme conditions for this type

of machinery are generally those where the

ambient temperature range exceeds 41°–104°F;

the relative humidity range exceeds 20–95%

(non-condensing); or the environment is subject

to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power

source. Make sure all power cords are protected

from traffic, material handling, moisture,

chemicals, or other hazards. Make sure to leave

access to a means of disconnecting the power

source or engaging a lockout/tagout device.

Lighting

Lighting around the machine must be adequate

enough that operations can be performed

safely. Shadows, glare, or strobe effects that

may distract or impede the operator must be

eliminated.

Children or untrained people

may be seriously injured by this

machine. Only install in an access

restricted location.

Figure 3. Working clearances.

22

1

⁄2"

35

1

⁄2"

(Ensure adequate outfeed distance) (Ensure adequate infeed distance)

Feed Direction

-15-

Model W1854 (For Machines Mfd. Since 04/18)

SETUP

Assembly

Before beginning the assembly process, refer to Items

Needed for Setup

and gather everything you need.

Ensure all parts have been properly cleaned of any

heavy-duty rust-preventative applied at the factory (if

applicable). Be sure to complete all steps in the assembly

procedure prior to performing the Test Run.

To assemble machine, do these steps:

1. Move sander crate to an appropriate location, as

described in Machine Placement on previous page.

2. Mount a top and bottom long bracket to a stand

leg and secure by hand with (2) M8-1.25 x 15

carriage bolts and (2) M8-1.25 flange nuts, as shown

in Figure 4.

3. Secure a second leg to top and bottom long brackets

with (2) M8-1.25 x 15 carriage bolts and flange nuts,

as shown in Figure 5.

4. Repeat Steps 2-3 with remaining components to

build remaining stand leg assembly.

5. Mount top and bottom short brackets to stand leg

assembly with (2) M8-1.25 x 15 carriage bolts and

(2) M8-1.25 flange nuts, as shown in Figure 6.

Do not final-tighten stand bolts until all stand

components have been assembled. It will help with

aligning and leveling stand later in assembly steps.

Figure 7. Completed stand assembly.

x10

Note: We recommend assembling the stand upside down.

To make it easier, have an assistant hold the pieces while

you assemble the stand.

6. Assemble remaining stand components, as shown in

Figure 7, with remaining hardware.

Figure 4. Top and bottom long brackets

secured to a stand leg.

x2

Leg

Bottom Long

Bracket

Top Long

Bracket

Figure 5. A completed stand leg assembly.

x2

Leg

Figure 6. Top and bottom short brackets

secured to stand leg assembly.

x2

Bottom

Short

Bracket

Top Short

Bracket

-16-

Model W1854 (For Machines Mfd. Since 04/18)

SETUP

USE helpers or power

lifting equipment to lift

this machine. Otherwise,

serious personal injury

may occur.

Figure 10. Mounting sander to stand.

x4

7. Turn stand upright and adjust it so legs are evenly

positioned, then tighten all stand fasteners.

8. Make sure sander is still resting on shipping pallet.

9. Place pallet and stand near appropriate location

(once sander is mounted to stand it will be difficult

to move).

10. With help of an assistant, tilt sander back so side

with belt access panel faces pallet. Move left bottom

edge of sander forward, as shown in Figure 8.

Note: The base should be even with or stick out

from the edge of the pallet to properly install stand

assembly.

12. Secure stand to sander with (4) M8-1.25 x 20 hex

bolts, (8) 8mm flat washers, and (4) M8-1.25 hex

nuts, as shown in Figure 10.

13. Lift up on stand and remove blocks.

11. Lay stand assembly on blocks, as shown in

Figure 9.

Tip: Place two stacks of blocks the same height as

the pallet and about 15 inches apart on the floor

near the sander base, and lay the stand assembly on

the blocks, as shown in Figure 9.

Figure 8. Sander tipped back on pallet

against belt access panel.

Pallet

Figure 9. Stand resting on blocks.

Blocks

15" Apart

-17-

Model W1854 (For Machines Mfd. Since 04/18)

SETUP

If the legs start to slide when tilting sander upright,

you MUST have a third person hold the stand to keep

it from sliding to avoid personal injury or machine

damage!

Figure 11. Tilting sander upright.

15. Install table elevation handwheel. Slide handwheel

slots over shaft pin, as shown in Figure 12. Secure

with pre-installed M6-1 x 35 cap screw and 6mm

fender washer.

14. With help from an assistant, carefully tilt sander

upright, as shown in Figure 11, so rear legs touch

floor.

Figure 12. Installing handwheel.

Shaft Pin

Slots

Page is loading ...

Grizzly W1854 Owner's manual

Grizzly W1854 Owner's manual

Related papers

Other documents