680
Additional Instructions
Assembling the extraction system
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2017
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
2 Additional Instructions 680 - 00.0 - 06/2017
General information
Additional Instructions 680 - 00.0 - 06/2017 3
1 General information
Check whether the scope of delivery for kit 0680 590004 is correct prior to
installation.
Part number Quantity Description
0275 590130 1 Waste bin
0275 590140 1 Air suction device
0275 590150 1 Pedal valve
0680 590014 1 Collecting bin
0680 330750 1 Pressure plate
0680 330760 1 Pressure plate
0744 001819 1 Double nipple
0744 009491 1 Distributor
0999 240392 1 VI-E coupling screw
9202 002887 2 Cylinder-head bolt
9202 002957 1 Cylinder-head bolt
9217 300507 4 Pan-head screw
9792 071010 1 Blanking plug
9792 301010 2 Sealing ring
0791 680704 EN 1 Additional Instructions
Assembling the extraction system
4 Additional Instructions 680 - 00.0 - 06/2017
2 Assembling the extraction system
Fig. 1: Assembling the extraction system (1)
To assemble the extraction system:
1. Assemble the vent (2) to the throat plate using the screws (1).
Fig. 2: Assembling the extraction system (2)
2. Assemble the hose (4) to the vent (2) using the clip (3).
(1) - Screws (2) - Vent
①
②
(2) - Vent
(3) - Clip
(4) - Hose
②③ ④
Assembling the extraction system
Additional Instructions 680 - 00.0 - 06/2017 5
Fig. 3: Assembling the extraction system (3)
3. Insert the screws (6) through the plate (5) from the top.
4. On the back, screw the plate (5) in place in a slanted position under
the tabletop.
• approx. 32 cm away from the right edge of the tabletop
• the left side approx. 1 cm away from the rear edge of the tabletop
• the right side approx. 3 cm away from the rear edge of the tabletop
5. Insert the nuts (7) into the holder (8).
6. Screw the holder (8) onto the screws (6).
(5) - Plate
(6) - Screws
(7) - Nuts
(8) - Holder
1cm
3cm
⑧
⑤⑥⑦
32 cm
Assembling the extraction system
6 Additional Instructions 680 - 00.0 - 06/2017
Fig. 4: Assembling the extraction system (4)
7. Hook the air nozzle (11) into the holder (8).
Make sure that the throttle valve (10) is pointing to the left towards the
vent (2).
8. Assemble the hoses (4) and (12) to the air nozzle (11) using the
clips (9).
Fig. 5: Assembling the extraction system (5)
(4) - Hose
(8) - Holder
(9) - Clips
(10) - Throttle valve
(11) - Air nozzle
(12) - Hose
⑩
⑨
⑫
⑧
⑧
④
⑨
⑪
(12) - Hose
(13) - Suction container
(14) - Bracket
⑭
⑫
⑬
Assembling the extraction system
Additional Instructions 680 - 00.0 - 06/2017 7
9. Screw the bracket (14) under the tabletop.
10. Screw the suction container (13) to the bracket (14).
11. Connect the hose (12) to the suction container (13).
Fig. 6: Assembling the extraction system (6)
(10) - Throttle valve
(15) - Pedal rod
(16) - Air hose
(17) - Pneumatic switch
(18) - Compressed air connection
(19) - Compressed air maintenance unit
⑮
⑯
⑰
⑩
⑮
⑯
⑱
⑰⑱⑲
Assembling the extraction system
8 Additional Instructions 680 - 00.0 - 06/2017
12. Shorten the pedal rod (15) to a length of approx. 18 cm.
13. Assemble the pneumatic switch (17) to the pedal rod (15).
14. Connect the air hose (16) to the throttle valve (10) and output 1 on
the pneumatic switch (17).
15. Connect the compressed air connection (18) to the compressed air
maintenance unit (19) and the center connection on the pneumatic
switch (17).
Information
Fig. 7: Assembling the extraction system (7)
The switch (20) switches the extraction system on when the pedal is
pressed.
The extraction system will switch on before the sewing process starts.
(20) - Switch
⑳
DÜRKOPP ADLER AG
Potsdamer Str. 190
33719 Bielefeld
Germany
Phone: +49 (0) 521 925 00
Email: [email protected]m
www.duerkopp-adler.com
Subject to design changes - Part of the machines shown with additional equipment - Printed in Germany
© Dürkopp Adler AG - Additional Instructions - 0791 680704 EN - 00.0 - 06/2017
/
