Pottinger TOP 972 C s-line Operating instructions

Brand: Pottinger

Model: TOP 972 C s-line

Category: Mini tillers

Type: Operating instructions

This manual is also suitable for

TOP 852 C s-line

Operator‘s manual

+ INSTRUCTIONS FOR PRODUCT DELIVERY . . . Page 3

"Translation of the original Operating Manual" Nr.99 2502.GB.80M.0

• Double Rotary Swather

TOP 852 C s-line

(Type SK 2501 : + . . 01124)

TOP 972 C s-line

(Type SK 2502 : + . . 01076)

ALLG./BA SEITE 2 / 0000-GB

Important information concerning Product

Liability.

According to the laws governing product liability, the manufacturer and dealer are obliged to hand the

operating manual to the customer at the time of sale, and to instruct them in the recommended operating,

safety, and maintenance regulations. Confirmation is necessary to prove that the machine and operating

manual have been handed over accordingly.

For this purpose,

- document A is to be signed and sent to Pöttinger,

- document B remains with the dealer supplying the machine,

- and the customer receives document C.

In accordance with the laws of product liability, every farmer is an entrepreneur.

According to the laws of product liability, property damage is damage caused by a machine and not to

it. An excess of Euro 500 is provided for such a liabilioty.

In accordance with the laws of product liability, entrepreneurial property damages are excluded from

the liability.

Attention! Should the customer resell the machine at a later date, the operating manual must be given

to the new owner who must then be instructed in the recommended regulations referred to herein.

GB Dear Farmer

You have just made an excellent choice. Naturally we are very happy

and wish to congratulate you for having chosen Pöttinger. As your

agricultural partner, we offer you quality and efficiency combined with

reliable servicing.

In order to assess the spare-parts demand for our agricultural machines

and to take these demands into consideration when developing new

machines, we would ask you to provide us with some details.

Furthermore, we will also be able to inform you of new developments.

Pöttinger Newsletter

www.poettinger.at/landtechnik/index_news.htm

The latest expert information, useful links and entertainment

Dokument D

GB-0600 Dokum D Anbaugeräte

PÖTTINGER Landtechnik GmbH

Industriegelände 1

A-4710 Grieskirchen

Tel. 07248 / 600 -0

Telefax 07248 / 600-2511

T Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating

devices at hand.

T Operation and maintenance of machine and/or implement according to operating instructions explained to the customer.

T Tyres checked re. correct pressure.

T Wheel nuts checked re. tightness.

T Drive shaft cut to correct lenght.

T *VYYLJ[WV^LY[HRLVɈZWLLKPUKPJH[LK

T Fitting to tractor carried out: to three-point linkage

T Trial run carried out and no defects found.

T Functions explained during trial run.

T Pivoting in transporting and operating position explained.

T Information given re. optional extras.

T Absolute need to read the operating manual indicated.

Please check. X

According to the product liability please check the above mentioned items.

INSTRUCTIONS FOR

PRODUCT DELIVERY

In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.

For this purpose please do the following:

- sign the document A and send it to the company Pöttinger or via the internet to www.poettinger.at

- document B stays with the specialist factory delivering the machine.

- document C stays with the customer.

- 4 -

1200_GB-Inhalt_2502

TABLE OF CONTENTS

Observe

Safety

Hints in the

supplement!

Table of contents

TABLE OF CONTENTS

Meaning of warning signs..........................................5

CE sign ......................................................................5

GENERAL SAFETY TIPS

Travelling with implement in tow ...............................6

Coupling and uncoupling the implement ..................6

Regulations for Use ...................................................6

Travelling on roads .....................................................6

Before starting work ..................................................6

Checking before operation ........................................6

DESCRIPTION OF SERVICES

Overview .................................................................... 7

Versions .....................................................................7

TRACTOR REQUIREMENT

Tractor ........................................................................8

Ballast weights ..........................................................8

Lifting Unit (Three-point Linkage) ..............................8

Required Hydraulic Connections ...............................8

Required Power Connections ....................................8

ATTACHING THE MACHINE

Machine attachment ..................................................9

Connecting the cardan shaft .....................................9

Set up electric connection .......................................10

Fold support wheel up .............................................10

Hydraulic connections – model: Standard ..............10

Adjusting the linkage at the transport securing

device ......................................................................11

TRANSPORT

Switching from working to transport position .........12

Driving on Public Roads ..........................................13

Unit’s Dimensions in Transport Position ..................13

Frame Chassis .........................................................14

SELECT CONTROL

Features of the Terminal ..........................................15

Commissioning ........................................................ 15

User Interface ..........................................................16

Functions .................................................................16

USE

Switching from transport to working position .........20

Adjusting the Working Width ...................................21

Adjust rake height ....................................................21

Conversion to special rake height ...........................22

Height adjustment of swath curtain .........................22

Adjust Rotor Chassis ...............................................22

Adjusting the pretension of the relieving springs ...23

Switching from Working to Field Transport

Position .................................................................... 23

Speed of PTO drive shaft ........................................23

WORKING ON SLOPES

Take care when turning on slopes! ..........................24

MAINTENANCE

Safety point .............................................................25

General maintenance hints ......................................25

Cleaning of machine parts .......................................25

Parking in the open ..................................................25

Winter storage .........................................................25

Drive shafts ..............................................................25

Hydraulic unit ...........................................................25

Gears .......................................................................26

Chassis ....................................................................26

Spring tines ..............................................................26

Tyres ........................................................................26

Rotor Unit ................................................................27

Lubrication chart ......................................................29

Lubricating the telescopic arm: ...............................30

Winter storage: ........................................................30

TECHNICAL DATA

Donnees Techniques ...............................................31

Defined use of the Rotary Swather ..........................31

Position of Vehicle Identification Plate ....................31

SERVICE

Hydraulic diagram (standard) ..................................32

Hydraulic diagram (Select Control) ..........................33

Circuit diagram (Select Control)...............................34

Circuit diagram (Select Control)...............................35

SUPPLEMENT

Recommendations for work safety .........................38

Driveshaft .................................................................40

Lubricants ................................................................ 42

Combination of tractor and mounted implement ....44

- 5 -

1200_GB-Inhalt_2502

TABLE OF CONTENTS GB

CE sign

The CE sign, which is affixed by the manufacturer, indicates outwardly that this machine

conforms to the engineering guideline regulations and the other relevant EU guidelines.

EU Declaration of Conformity

By signing the EU Declaration of Conformity, the manufacturer declares that the machine

being brought into service complies with all relevant safety and health requirements.

Meaning of warning signs

Do not enter rotor area while driving

motor is running.

Never reach into the crushing danger

area as long as parts may move.

Stay clear of swinging area of

implements

495.173

Observe

Safety

Hints in the

supplement!

- 6 -

0800_GB-AllgSicherheit_3842

Travelling with implement in tow

The attached implement influences the travelling

characteristics of the towing vehicle.

• Danger of tipping exists when working on slopes.

• The driving must be adapted to the corresponding

terrain and ground conditions.

• The towing vehicle is to

be sufficiently equiped

with weights at the front

or at the rear in order to

guarantee the steering

and braking capacity (a

minimum of 20% of the

vehicle's tare weight on

the front axle).

• Transporting people on the implement is not

permitted.

Coupling and uncoupling the implement

• Danger of injury exists when coupling the implement

to the tractor!

• When coupling, do not stand between tractor and

implement while tractor is reversing !

• No-one must enter the area between tractor and

implement unless both vehicles have been secured

against rolling with wheel chocks !

• Drive shaft connection or disconnection is only to

be undertaken when the motor has stopped.

Regulations for Use

Regulations for Use: See chapter „Technical Data“.

• The trailer‘s load limits (permitted axle load, support

load, total weight) may not be exceeded.The relevant

details are located on the right side of the trailer.

• In addition, observe the power limits of the tractor

being used.

Travelling on roads

• Observe the road rules

GENERAL SAFETY TIPS

20%

Important!

General safety

hints for the use

of this implement!

Before starting work

a. Before commencing work, the operator must be aware

of all operating devices and functions.The learning

of these is too late after having already commenced

operation!

b. Before commencing any work check that implement

is safe for road travel and operation.

c. The danger of being crushed or cut exists in the Pick-

up, cutting unit, tailgate and upper extension areas.

d. Before driving the vehicle, the driver must ensure that

nobody will be endangered and that no obstructions

are present. If the tractor driver does not have a clear

view of the roadway immediately behind the implement,

he must be guided when reversing.

e. Observe the safety information fixed to implement.

An explanation of what the individual graphic warning

symbols mean can be found on page 5.

f. Observe also the tips in the respective chapters and

in the supplement to this operating manual.

Checking before operation

The following tips should make preparing the implement

for operation easier. Detailled information for individual

points can be found in the respective chapters in this

operating manual.

1. Check that all safety equipment (covers, casings, etc.)

is in good condition and fixed in the proper positions

of protection on the implement

2. Grease and oil the implement according to the

lubrication chart. Check the gearing for tightness and

the oil level.

3. Check that tyres have the correct air pressure.

4. Check that wheel nuts are sitting firmly.

5. Ensure the correct p.t.o.-r.p.m.

6. Make the electrical connections to the tractor and

check that they are correct. Take note of the tips in

the operating manual!

7. Carry out the following adaptions:

• Drawbar height

• Cardan shaft length

8. Secure the implement only with the equipment

provided.

9. Cut drive shaft to correct length and check that overload

safeguard is functioning (see Supplement)

10.

Check the electronic unit function.

11.

Connect hydraulic lines to tractor.

• Check hydraulic hoses for damage and wear.

• Ensure the correct connection.

12.

All swivelling parts must be secured against dangerous

position changes.

13.

Check parking brake and service brake functions.

0900-GB_ÜBERSICHT_2502

- 7 -

DESCRIPTION OF SERVICES

Maximum working width:

9.80 m

Overview

Designations:

(1) Coupling jack

(2) Support leg

(3) Hoop guard for left-hand rotor

(4) Left-hand rotor chassis incl. sensor wheel

(5) Left-hand rotor

(6) Swath curtain

(7) Chassis tyres

(8) Lighting

(9) Chassis frame

(10) Transport lock

Versions

Designation DESCRIPTION

TOP 852 C s-line Maximum working width: 8.40 m

Rotor diameter: 3.70 m

TOP 972 C s-line Maximale Arbeitsbreite: 9,80 m

Rotor diameter: 4.30 m

4 5 6

7 8

0900-GB_SCHLEPPER VORAUSSETZUNG_2502

- 8 -

TRACTOR REQUIREMENT

Tractor

The following tractor requirements must be met for operation of this machine:

- Tractor power: 37 kW/50 bhp

- Attachment: lower link cat. II

- Connections: see table “Required hydraulics and power connections”

Ballast weights

The tractor must be fitted with sufficient ballast weights at the front to

ensure steering and braking ability.

At least 20% of the unloaded vehicle weight on the

front axle.

Lifting Unit (Three-point Linkage)

- The tractor’s lifting unit (three-point linkage) must be designed for

the load arising. (See technical data)

- The lifting rods must be adjusted to the same length using the

corresponding adjusting device (4).

(See tractor manufacturer’s operating instructions)

- Select the rear position if the lifting rods can be adjusted in various

positions on the lower link. This relieves the pressure on the tractor’s

hydraulic system.

- The limiting chains or stabilisers of the lower link (5) must be adjusted

so that there is no possibility of the attached implements moving

laterally. (Safety measures for transport journeys)

Required Hydraulic Connections

Version Consumer Single-acting

hydraulic

connection

Double-acting

hydraulic

connection

Marking

(Implement side)

Standard Raising and lowering of the rotors X*) 1

Standard Working width X 2

*) Floating position necessary

Required Power Connections

Version Consumer Pole Volt Power connection

Standard Lighting 7-polig 12 VDC to DIN-ISO 1724

20%

371-08-16

- 9 -

1201-GB_ANBAU_2502

ATTACHING THE MACHINE

Safety

advice:

see Supplement

A1, points1-8.

Machine attachment

Connecting the cardan shaft

- Turn motor off and remove ignition key

- Clean and grease machine’s attachment profile and tractor’s p.t.o. shaft before attaching cardan shaft.

- Attach wide angle joint (4) to machine first. Then attach cardan shaft to tractor’s p.t.o. shaft

- To prevent protector cap on all shafts from turning, secure it with chain (5)

Attention!

Check the length of the PTO drive shaft

and adapt if necessary prior to starting up

for the first time.

Shortest possible operating position (L2):

1. Lifting gear right down

2. Steering is completely turned to lock.

(See adjacent diagram)

See the section "Adjustment of PTO Drive Shaft" in

Attachment B of these Operating Instructions for details.

025-05-04

Attach swather:

- Connect coupling jack to lower link of tractor

- Secure coupling bolts (1) properly

- Bring the chassis frame into a horizontal position or

adjust the height of the lower link (X) to 70 cm.

Attention!

Switch off the

engine, remove

the key and

secure the

tractor against

rolling before

carrying out any

maintenance or

repair work!

- 10 -

1201-GB_ANBAU_2502

ATTACHING THE MACHINE GB

Set up electric connection

Lighting

- Connect 7-channel plug to tractor

- Check that lighting is functional on machine

Fold support wheel up

- Swing jack stand up after attaching the machine (5b)

- Push jack stand foot down with your foot and then

swing up

- The pin locks automatically

Attention:

Jack stand

will swing up

automatically

when disengaged

- Danger of

crushing!

Hydraulic connections – model: Standard

Connect hydraulic lines at tractor

- Turn p.t.o. off before connecting

- Put lever (ST) on the control unit into the floating position

(0).

- Take care that snap-lock couplers are clean.

- Only connect hydraulic system to the tractor when

stopcock is closed (position A).

- Route cable (S) into tractor cab

- 11 -

1201-GB_ANBAU_2502

ATTACHING THE MACHINE GB

Adjusting the linkage at the transport securing device

Adjust the linkage of the transport securing device correctly before the first putting into operation. Check that the rotor

arms can be lifted hydraulically in locked status.

1. Lift unit to transport position

2. Control device in floating position

3. Loosen lower nut (1).

4. Screw upper nut (2) downwards until the rotor arm

lifts when you set the control device to "Lift".

5. Lock position with lower nut (1)

6. Place unit in headland position

7. Set control device to "Lift".

If the rotors now move in transport position, without

the rope being released by pulling beforehand,

then turn the bolt (3) downwards until movement

in transport position is no longer possible.

1000_GB-TRANSPORT_2502 - 12 -

TRANSPORT

Switching from working to transport position

Attention!

Only carry out

the switch from

working to trans-

port position and

back on level,

firm ground.

Ensure that the

pivoting area is

free and there is

no-one present in

the hazard area.

075-09-07

Requirement for switching to transport

position:

- Retract extendable rotor arms fully.

- Minimise rake height so as not to exceed the max.

transport width of 3 m.

1. Turn in outer sensor wheels (optional)

Both sensor wheels must be pivoted to the innermost

position for the transport position.

- Pull cable (1).

- Turn sensor wheel inwards and secure on innermost

catch (2).

2. Reduce transport dimensions

(Only necessary for Top 972 C s-line version)

2.1 Hoop guard

Hoop guards (3) must be pivoted towards the back to

reduce the overall height of the rotary swather.

- Unlatch hoop guard (3) for each rotor with cable (4)

and pivot backwards until it has locked audibly into

position again.

- Retract extended additional hoops on front lighting

beam and secure!

2.2 Remove tine carriers

Tine carriers (5) may be removed to reduce the overall

height of the rotary swather.

- Remove 5 tine carriers (5) per rotor, place in holder on

frame and secure.

3. Raising the rotors

- Raise the rotors into the field transport position using

the dual-action control device.

- Retract extendable rotor arms fully.

- Pull cable (6) and raise rotors completely using dual-

action control device.

- Release cable.

- Check proper latching of transport lock (7).

Attention!

Switch off PTO

drive shaft for

safety reasons

and wait until the

rotors come to a

stop.

6 7

2 1

4 3

Attention

Check the trans-

port lock for pro-

per latching prior

to transport! The

latching hooks of

the transport lock

(7) must engage

fully in the pins of

the rotors.

Note for

hoop guard:

“Hydraulic hoop

guard pivoting”

version - the

hoop guards pivot

automatically

when raising and

lowering.

TRANSPORT

1000_GB-TRANSPORT_2502 - 13 -

Take note!

Before transporta-

tion, check the

position of the lif-

ting cylinder. The

cylinder must be

in the narrowest

position!

Driving on Public Roads

Attention!

- Comply with the regulations issued by your country’s legislative authority.

- Travelling on public roads is only permitted as described in the section “Transport Position”.

- Protective devices must be attached and in a proper condition.

- Pivotable parts must be brought into the correct position prior to starting travel and must be secured

against changes in position which could present a hazard.

- Check that the lighting functions prior to starting travel.

- Push protective strips onto the spring tines facing outwards.

Attention!

Always close shut-

off valves during

road transport.

Otherwise hazard

to other road

users due to

unintentional

operation of the

hydraulic control

system.

Unit’s Dimensions in Transport Position

The following dimensions will not be exceeded when the

transport position is established properly:

Type Height (h) Width (m) Length (m)

TOP 852 C

s-line 3,99 (3,40*) 3,00 7,85

TOP 972 C

s-line 4,75 (3,85*) 3,00 8,28

* Transport height with tines removed

TRANSPORT

1000_GB-TRANSPORT_2502 - 14 -

Frame Chassis

The frame chassis is steerable. The rotatable coupling jack

transfers the steering movement to the frame chassis by

means of a steering rod.

With the best possible basic setting, the frame chassis

follows the tractor in alignment when travelling straight

ahead. (see diagram)

The length of the steering rod may be adjusted if it is

discovered that the frame does not follow in alignment.

The adjusting unit is located on the coupling jack.

- Unscrew lock nut

- Adjust length of steering rod

- Tighten lock nut

044-01-009

Attention!

The chassis must

be checked by

means of a visual

inspection before

beginning a trans-

port journey!

- 15 -

1201_GB-Select Control_2502

SELECT CONTROL

Features of the Terminal

Electrical Connection

The terminal’s electricity is supplied via a plug in accordance with DIN 9680 from the tractor’s 12 V on-board electrical

system. These 3-pin plugs are also used in a 2-pin version as only the two main connections (+12 V, earth) are required.

Caution!

Plugs and sockets of a different design are not permissible as functional safety is not guaranteed.

Technical Data

Operating voltage: +10V ......+15V

Operating temperature range: -20°C ...... +60°C

Storage temperature: -30°C .... +60°CL

Degree of protection: IP65

Fuse: 10 A multi-fuse in operatingvoltageplug.

Function

The hitched unit is operated via a dual-action control device at the tractor, whereby the individual functions can be

preselected at the Select Control terminal. The preselected functions are displayed on the LDC screen of the terminal.

Commissioning

1. Positioning

Position the Select Control terminal so that it is easily

visible in the tractor cab. (There is a magnet on the rear

for attaching the terminal.)

2. Connection

Connect plug (1) to the 12V power supply of the tractor.

Connect plug (2) to 7-pin connection at job computer of unit.

3. Switching on and off

Press the “I/O” key to switch on the terminal.

Keep the “I/O” key depressed for 3 seconds to

switch off the terminal.

Upon switching on the terminal, the initial screen is shown.

The version numbers or the currect Select-Control Software

(FO92) and the interfaces software (LIN-IO) can be seen

in the lower section of the start screen.

Pöttinger

Rakes - TOP

Vers. FO92: V 1.0

Vers. LIN-IO: V 1.0

- 16 -

1201_GB-Select Control_2502

SELECT CONTROL GB

User Interface

Keys

a Hour counter (current and total hours)

b Transport locking

c Road transport

d Preselection left rotor unit

e Preselection swath width

f Preselection right rotor unit

g Preselection rake height left/arrow downwards

h Preselection rake height right/arrow upwards

i I/O or menu

Operating notes

To preselect a function, press the appropriate key.

The preselected function will be displayed on the screen.

Functions

1. Pivoting rotor unit(s) between working and field transport position:

The key "Preselection left or right rotor unit" selects the rotor unit you wish to pivot.

The pivot procedure is performed by the control unit.

Keys Display Note

+ Both rotors are pivoted between the “field transport” and “working

position” position using the tractor’s control unit.

/ The selected rotor is pivoted between the “field transport” and “working

position” position using the tractor’s control unit.

(Press a preselection key twice in succession to select both rotor units )

2. Setting working width:

This key preselects the function "Adjust working width". The pivot procedure is performed by the control unit.

Keys Display Note

The working width of both rotors is adjusted using the tractor’s control

unit. This function is possible in the “field transport” and “working

position” position.

- 17 -

1201_GB-Select Control_2502

SELECT CONTROL GB

3. Adjusting rake height:

This key selects the function "Adjust rake height" This function is performed by the control unit.

Keys Display Note

+ The rake height of both rotors is adjusted using the tractor’s control unit.

/ The rake height of the selected rotor is adjusted using the tractor’s control unit.

(Press a preselection key twice in succession to select both rotor units )

4. Pivoting from field transport to road transport position.

This key selects the function "Pivot to road transport". This function is performed by the control unit.

Precondition for this function: Standstill of cardan shaft and field transport position of both rotor units!

Keys Display Note

Both rotors are pivoted between the “field transport” and “working

position” position using the tractor’s control unit. The “field transport”

position is a requirement for this function.

The “working width” function is activated first if the minimum

working width has not been set in the “field transport” position.

If the sensors signal “minimum working width” then the switch is

made to the “road transport” function. The function is deactivated

automatically as soon as the “field transport” position is reached.

If the cardan shaft is moving and you press the "Road transport" key, the

warning to the right appears on the screen.

Wait until the cardan shaft has stopped moving before you pivot the unit to

road transport position.

Caution!

There is a danger

of tipping when

pivoting procedu-

re is performed

on an incline!

- 18 -

1201_GB-Select Control_2502

SELECT CONTROL GB

5. Swinging from the “Road transport" to the “Field transport” position:

Caution!

The transport locking device can be activated separately in the event of a malfunction.

Once the key "Transport locking" is no longer depressed, the rotors in the display

appear empty until another function is selected. You can control only the transport

locking device with the control unit as long as the rotors in the display are empty.

Keys Display Note

1. 1. (1) Preselect key "Road transport",

2. 2. 2) Keep key "Transport locking" depressed and activate the

control unit of the tractor (lift) until the transport securing

device has unlocked.

3. 3. (3) Activate key "Road transport" and switch the control unit

of the tractor to "Lower" until the field transport position is

reached.

4. 4. (4) Once the field transport position has been reached, press

the "Road transport" key or the "Preselection left/right rotor

unit" key. Both rotor units have been preselected.

6. Data Menu

Keys Display Note

Press the key "Data menu" for a short time to get to the current

hour counter (Data 1).

Press the key "Data menu" for a long time to set the current

hour counter to 0.

The hour counter counts how long the cardan shaft has been

running.

Press the key "Data menu" once again for a short time to get

to the total hour counter (Data 2).

Press the key "Data menu" once again for a short time to get

to the working area.

- 19 -

1201_GB-Select Control_2502

SELECT CONTROL GB

7. System Menu

Keys Display Note

Press the key "IO" for a short time to get to the brightness

menu. Adjust the brightness of the display using the arrow keys.

Notre: When selecting a brightness of <30%, the key lighting

will be activated.

Press the key "IO" once again for a short time to get to the

contrast menu. Adjust the contrast of the display using the

arrow keys.

Press the key "IO" once again for a short time to get to the

sensor test display.

Press the key "IO" once again to get to the working area.

7.1 Sensor test display

Icon Description Note

- + 14,2 V

Current supply voltage The current supply voltage should

be greater than 12V with the tractor

running.

0 r

Drive shaft speed in rpm

Sensor swath width left Black: active when swath width

minimum

white: inactive

Sensor swath width right Black: active when swath width

minimum

white: inactive

Hall effect sensor - drive shaft black: magnet at the sensor

white: different position of the magnet

Sensor left rotor unit Black: active - field transport/road

transport

white: inactive

Sensor right rotor unit Black active field transport/road

transport

white: inactive

- 20 -

1200_GB_Einsatz_2502

USE

Switching from transport to working position

Attention!

Hydraulic lowering of the rotors must be

carried out in one continuous operation.

Undefined raising/lowering of individual

rotors may occur if occasional stops are

made.

1. Lowering of the rotors

- Raise rotors briefly using dual-action control device to

release transport lock.

- Pull cable (1) and lower rotors completely using dual-

action control device.

- Release cable (1).

2. Deactivate transport measures

(Only necessary for Top 972 C s-line version)

2.1 Attach tine carriers

Attach the tine carriers transported on the frame to the

rotors.

- Attach the rotors and secure in each case with the

cotter pin!

2.2 Pivot hoop guard into position

- Unlatch hoop guard (3) for each rotor with cable (4) and

pivot forwards until it has locked audibly into position

again.

- Extend auxiliary hoop on front lighting beam for each

rotor and set according to working width.

3. Position outer sensor wheels (optional)

The outer sensor wheels may be set for the best possible

conditions of use according to the crop.

- Pull cable (5).

- Pivot sensor wheel into position, release cable and

allow sensor wheel to engage.

075-09-05

Attention!

Only carry out the

switch from wor-

king to transport

position and back

on level, firm

ground.

Ensure that the

pivoting area is

free and there is

no-one present in

the hazard area.

1 2

4 3

Note for

hoop guard:

“Hydraulic hoop

guard pivoting”

version - the

hoop guards pivot

automatically

when raising and

lowering.

Attention!

Hazard from rotat-

ing tines

Switch the rake

off before you

leave the cabin or

if any persons ap-

proach the hazard

area.

Page is loading ...

Pottinger TOP 972 C s-line Operating instructions

Brand: Pottinger

Model: TOP 972 C s-line

Category: Mini tillers

Type: Operating instructions

This manual is also suitable for

TOP 852 C s-line

Download PDF

report

Pottinger TOP 972 C s-line Operating instructions

This manual is also suitable for

Pottinger TOP 972 C s-line Operating instructions

Related papers

Other documents