Bretford EDUSXTM60CNOX01 Operating instructions

EXPLORE® 4-Leg Teaming Table

with Screen Share

Assembly Instructions

This product includes electronic hardware and should be installed by a qualied individual.

Installation time of 4 hours or more for this table should be expected.

Two people are suggested when setting the angle and position of your monitor.

Monitor Display Requirements: your at panel display must conrm to the following

requirements.

yWith the stand removed, the monitor must not exceed 40 lbs.

yFeature a mounting hole pattern 200mm x 200mm or smaller.

yHDMI input with native resolution of 1080p.

yReturn to the last HDMI input programmed when powered on.

ySleep mode must be disabled to use the Power Controller.

yTeaming Table with Screen Share is optimized to mount monitors up to 40” but can

accommodate a larger display as long as it meets the above specications. Always check

monitor specications before purchasing your display.

Bretford provides some Allen wrenches required for assembly but you will need the

following tools to complete your installation.

yPhillips screw driver with large head

yPhillips screw driver with small head

yWire cutters

yWire strippers

yScissors

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

2

Wood Top - Qty 1

(Part number varies by model number)

Top Stiffener - Qty 2

60” & 72”= 017-0519, 84”= 017-1191

Cord Bin - Qty 1

60”= 060-1126, 72” & 84”= 060-1127

FPP1M0 - Qty 1

Low prole vesa mount

010-6386 - Qty 1

Transition mounting plate

010-4381 - Qty 1

Steel Plate

017-1170 - Qty 4

Lower Leg

022-3203 - Qty 4

Upper Leg

010-4889 - Qty 1

28” Pole

015-0175 - Qty 4

2 1/2” Stem Caster w/Brake

(Comes Installed into Lower Legs)

012-0753 - Qty 1

Pole Cap

012-0761 - Qty 2

Plastic Cord Clip

015-0045 - Qty 4

Threaded Glide

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

3

030-0354 - Qty 4or 6

10-32 x 1 1/2” L

Button Socket Screw

(60” & 72” = 4, 84”= 6)

030-0396 - Qty 8

3/8-16 x 1/2”

Socket Set Screw

030-0402 - Qty 10

#10-32 x 5/8”L

Combo Screw

030-1128 - Qty 4

1/4-20 UNC, 1 3/4”L

Socket Hd Screw

SC1054 - Qty 28

1/4-20 x 3/4”L

Philips Screw

030-1267 - Qty 4

M4 Nut

030-1234 - Qty 4

M4 x 0.7, 12 mm Long

Pan Head Screw

030-0397 - Qty 1

3/16” Allen Wrench

030-1237 - Qty 1

1/2” Allen Wrench

HK 1020 - Qty 1

5/32” Allen Wrench

030-0353 - Qty 1

1/8” Allen Wrench

030-1129 - Qty 1

5/8-11 UNC, 1 3/4”L

Socket Head Screw

030-1806 - Qty 2

Hook

Part No Description Quantity

012-0991 Leg Cord Management Clip 1

030-1762 Velcro Strips 4

044-2124 Display Courtesy Hardware Pack 1

Display hardware

pack Contents

Metric M4x12 screws 4

Metric M4x30 screws 4

Metric M5x12 screws 4

Metric M5x30 screws 4

Metric M6x12 screws 4

Metric M6x35 screws 4

Small washers 8

Large washers 20

5/8” Large spacers 4

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

4

Part Number Description Quantity

EXTRON X42 Package Kit

010-6921 Controller Bracket MBU123 1

010-6922 Switch Bracket MBU125 1

018-0695 2-Outlet Power Unit 2

018-0691 X42 Controller 1

018-0694 X42 HDMI/VGA Switch 1

018-0688 Cable Cubby 1400 1

023-1005 HDMI Ultra 12’ Cable 1

023-1006 HDMI “Show Me” Cable, 6’ 4

023-1008 VGA “Show Me” Cable, 6’ 2

023-1009 X42 Control Cable 1

080-1001 Extron Installation Guide - X42 1

EXTRON X60 Package Kit

010-6923 Controller Bracket MBU149 1

010-6922 Switch Bracket MBU125 1

018-0695 2-Outlet Power Unit 2

018-0690 X60 Controller 1

018-0693 X60 HDMI Switch 1

018-0688 Cable Cubby 1400 1

023-1005 HDMI Ultra 12’ Cable 1

023-1006 HDMI “Show Me” Cable, 6’ 6

023-1007 X40/60 RS232 Control Cable 1

080-1000 Extron Installation Guide - X40 & X60 1

EXTRON X40 Package Kit

010-6921 Controller Bracket MBU123 1

010-6922 Switch Bracket MBU125 1

018-0695 2-Outlet Power Unit 2

018-0689 X40 Controller 1

018-0692 X40 HDMI Switch 1

018-0688 Cable Cubby 1400 1

023-1005 HDMI Ultra 12’ Cable 1

023-1006 HDMI “Show Me” Cable, 6’ 4

023-1007 X40/60 RS232 Control Cable 1

080-1000 Extron Installation Guide - X40 & X60 1

Extron Screen Share Electronic Component Inventory

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

5

030-0354

(4)X

017-0519

(2)X

1

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

6

022-3203

(1) 4X SC1054

(7) 4X

2

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

7

015-0045

(4)X

017-1170

(4)X

3

For glide version tables only.

Skip this step if your table has casters.

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

8

Height Adjustment

Holes

030-0396

(2) 4X

Set screws are pre-installed in

your upper legs and need only be

loosened to insert lower leg section.

Tables using glides are height

adjustable from 20” to 30” at time

of assembly. Tables using casters

are height adjustable from 22” to

32” at time of assembly.

4

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

9

010-4889

(1)X

End with threaded

holes should face down

towards table surface.

010-4381

(1)X

030-1128

(4)X

030-1129

(1)X

5

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

10

This step is only for monitors that use a 200mm x

100mm or 200mm x 200mm mounting hole pattern.

FPP1M0

(1)X

030-1234

(4)x

030-1267

(4)x

To secure the mounting plate to the back of your monitor, a courtesy hardware pack (#044-2124)

has been provided with several metric screw sizes. You may need to purchase additional metric

screws from your local hardware store for a monitor with different mounting screw size.

Optimized for at panels up to 40” with no larger than a 200mm X 200mm mounting hole pattern.

The mount can accommodate a larger monitor as long as it meets the specications on the rst

page. Monitor weight may not exceed 40 lbs.

6

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

11

Follow this step for monitors that use a 200mm x

100mm or 200mm x 200mm mounting hole pattern.

Follow this step for monitors that use a 100mm x

100mm mounting hole pattern.

Screws provided

in courtesy

hardware pack

#044-2124.

Longer M4 screws are

available in the courtesy

hardware pack if required.

030-1234

(4)x

7

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

12

Quick release lever – Pull out

to insert into tube and adjust

monitor mount height.

Loosen screws prior to entry.

Tighten to secure in place.

For stability, Monitor mount must

install facing the work surface.

Monitor not

shown for

clarity

With someone’s help, slide the monitor mount

assembly into the pole. NOTE: Make sure

the screws in the spike are loosened and the

release lever is pulled out while sliding in the

spike. Once desired location is determined,

tighten spike screws.

8

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

13

Position your monitor to be horizontal with

the table top. Using a 1/8” Allen wrench

provided, tighten the set screw to prevent

rotational swivel.

Two people are suggested when setting the

angle and position of your monitor.

Position your monitor at the desired angle.

Using a 3/16” Allen wrench provided, tighten

the large bolt to maintain the monitor tilt

position.

012-0753

(1)X

9

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

14

Install the two 2-outlet power modules into the Cable Cubby using the lock washers, black screws,

and small screw driver provided by Extron. Bretford recommends you install them to the middle

height setting. Install one power unit for each Cable Cubby door and install both so they are closest

to the monitor.

TIP: Keep power cords secured with the twist ties until the cord bin is lifted into place.

Both power modules mount close to the monitor.

10

ISOMETRIC VIEW

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

15

Insert the Show Me cables into the plastic plates, half in the 1st plate and half in the 2nd plate. Show

Me cable buttons need to be above the plastic plate. Keep the twist tie on the lower portion of Show

Me cable in place at this time. Using the black screws provided by Extron, secure the plate to the top

of the small aluminum sleeves.

Fill unused holes in the plastic

cable plate with the plastic buttons

provided.

There are four aluminum sleeves, use the

shorter aluminum sleeves and discard the

longer pair.

11

12

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

16

Feed the assembly up through the bottom of the Cable Cubby and secure in place at the lowest

position using the lock washers and black screws provided by Extron.

13

ISOMETRIC VIEW

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

17

018-0688

(1)X

Move the latch brackets on the sides of the Cable Cubby down to the lowest

position with the levers pointing down. Rotate them at against the cubby wall.

Keeping the power outlets closest to the monitor mount, feed the cables

through the table opening and place the Cable Cubby into the table.

Slide the latch brackets up until

they are snug to the underside of

the work surface and lift the lever

upward to lock into place.

14

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

18

Attach the mounting brackets to your TeamWork Switch. The X40 (TeamWork 400) 4 user HDMI

switch utilizes Extron mounting brackets MBU123; The X60 (TeamWork 600) 6-user HDMI switch

utilizes Extron mounting brackets MBU149; The X42 (TeamWork 601) 6-user (4)HDMI/(2)VGA switch

utilizes Extron mounting brackets MBU123.

Install the rubber bumpers provided

by Extron to the top of the TeamWork

Switch.

15

16

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

19

Strip approximately 1” of the black cover off of the short extension from each of the Show Me cables.

Expose and separate the Red, Black and bare wires as shown.

17

EXPLORE 4-Leg Teaming Tables with Screen Share

Assembly Instructions

20

+V

2

C G TC G TC G T

46

1 3 5

Tx Rx G

C G TC G TC G T

+V

2

C G TC G TC G T

46

1 3

CONTACT IN/TALLY OUT

Tx

G

5

T Rx G

C CC T

G G T

+V

RS-232

For switches using both HDMI and VGA connections,

(versions X42) the Red hot wire attaches to the left

position marked “C” on the back of the switch and the

Black ground wire attaches to the right position marked

“T”. Bare wire is not used.

Using the small screwdriver provided, tighten the tally

port screws to each wire and secure the cables into

place using the thin white cable ties provided.

X42 four user switch

Connect each wire to the blue tally ports attached to the back of the TeamWork switch. For switches

using only HDMI connections, (versions X40 and X60) the Red hot wire attaches to the port marked

“Contact” on the back of the switch and the Black ground wire attaches to the port marked “Tally Out”.

Bare wire is not used.

18

Tx Rx

RS-232 AUTO

CONTACT

1 2 +V

1 2 G

TALLY OUT

3 4

3 4 Tx G

RS-232 AUTO

Rx

1 2 3 4G56G

1 2 3 4 +V 5 6+V

CONTACT

TALLYOUT

SW6 HDMI

X40 four user switch X60 four user switch

Page is loading ...

Bretford EDUSXTM60CNOX01 Operating instructions

Bretford EDUSXTM60CNOX01 Operating instructions

Related papers

Other documents