Jupiter JX05 User manual

Brand: Jupiter

Model: JX05

Type: User manual

Jupiter

Wireless earphone

User Manual

FCC ID: 2A847-JUPITER

TWS earphone x 2pcs

Charging base x 1pcs

Charging cable x 1pcs

Eearphone cap x 2pairs

User manual x 1pcs

What is in the box

Specification

Model No.：JX05

BT version：V5.3

I/O port：Type-C

Charging time: 3

Earphone weight: 3.55gx2

Total weight: 40.5g

Battery capacity (earphone): 40mAH

Battery capacity (Charging base): 300mAH

Music playing time: About 5.5H

Horn/driver diameter: 10mm

Transmission distance: 10m

Impedance: 32Ώ

Sensitivity: -42dB ± 3dB

Frequency response range: 20HZ-20KHZ

Charging base input : DC 5V-1A

Product Overview

1: Charging pins on the case

2. Charging base LED light

3. Power input Type-C port

4. Multi-function touch area

5. Earphone LED light

6. Charging pins on the earphone

7. Microphone

Use function

Charging

docking pin

Charging Base

LED light status

indicator

Earphone LED light

Power on/off

Answer/hang up

Refuse answer

the call

Music play/pause

next music

previous music

When the headset is off, press and hold the

touch button for 5 seconds to turn on

Touch the earphone 1 time on the

earphone ‘multi-function touch area’

Earphone long press for 3 seconds

to reject

Music status Double tap the touch key to

play/pause music

Triple click the next song on the right ear

Triple click left ear previous song

Quick touch the earphone ‘multi-function

touch area’three times to wake up SIRI

Quickly touch three times again to exit SIRI

Siri

charging

interface port

TYPE-C USB cable charging to charge the

charging base(DC5V/1A)

Bluetooth pairing

Note: Please be noted that the earphones will

automatically powered off if they are not paired to

any BT device in about 5 minutes.

Power on/off

Power on:

The earphones automatically power on when they are

taken out from the charging base. The blue light on the

earphone is on for 1 second.

Power off

If you don’t want to use the TWS earphone anymore,

placed back the TWS earphones to the charging base

and they will shut down automatically with the earphone

LED red light on for 1 second.

After power on, close the left and right earphones

(less than 3cm), when the left earphone and right

earphone is connected to each other successfully

it will be a beep sound "Dong", and then: host

earphone LED light is the red and blue lights flash

alternately, and the slave earphone LED light flashes

blue slowly, which means that the earphones are

ready for the pairing mode.

Now turn on the smartphone Bluetooth function, find

the pairing name: JX05, and click to connect the

smartphone with the JX05 TWS earphone. After they

are paired and connected successfully, the host

earphone LED blue light will flash slowly, now you

can enjoy the music cableless!

Take any one earphone out the R and L earphones

from the charging base, they will connect with each

other automatically. Now turn on the smartphone

Bluetooth function, find the pairing name: JX05

and click to connect the smartphone with the JX05

TWS earphone .After that ,put any one earphone

back to the charging base, the other earphone will

automatically connect with your smartphone. Now

you can only use one earphone!

Use Single Earphone only

How to restore to the factory default setting

Wear the earphones left and right. Place the earphones

with earplugs into the ear canal and turn them gently until

they fit comfortably without falling. The wrong way of

wearing will affect the signal of the headset and the call

of the microphone.

Wearing method

Big

earphone cap

Middle

earphone cap

Small

earphone cap

Tip: There are different size earphone caps for you

choose. For the best sound, choose an earphone

cap that completely seals your ear canal.

Attention:

Please read this user manual carefully before using the

product and keep it properly;

Do not disassemble or modify this product by yourself;

Do not place the product near heat sources;

Do not allow water or other liquids to flow into the product

and cause damage to the product;

Please store and use this product in normal temperature

environment;

Do not throw, to avoid product damage caused by falling;

Do not use chemical solvents to wipe this product;

Please use a USB charger with an output voltage of DC 5V

1A for charging;

The earphones are with built-in rechargeable lithium-ion

battery, the earphone battery must be fully charged before

you use it for the first time.

The phone is not connected to the six-click headset to

restore factory settings

Voice switching

The left and right earphones team up successfully (the

phone is not connected), and tap any earphone 5 times

to switch the prompt tone. After the successful switching,

there will be a prompt tone.

The charging docking pin is docked with the

charging contacts of the headset to charge

the built-in battery of the headset

Charge the headset: the white light is on

Charge the charging compartment: red

light flashes

Low battery in charging compartment: white

light flashes

Double click, second click and hold for 5s

to shut down

When the headset is on, press and hold the

touch button for 5 seconds to shut down

Take out the headset and turn it off

Earphone function indication

Charging

With Hall switch function, put the earphone into the charging

compartment, close the cover, earphoneTo start charging.

NOTE: This equipment has been tested and found to comply with

the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are

designed to provide reasonable protection against harmful

interference in a

residential installation. This equipment generates uses and can

radiate radio

frequency energy and, if not installed and used in accordance with

the instructions,

may cause harmful interference to radio communications.

However, there is no

guarantee that interference will not occur in a particular

installation. If this

equipment does cause harmful interference to radio or television

reception, which

can be determined by turning the equipment off and on, the user is

encouraged to

try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from

that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party

responsible for compliance could

void the user's authority to operate the equipment.

Jupiter JX05 User manual

Jupiter JX05 User manual

Other documents