Krone BA EasyCollect 6000 FP Operating instructions

O p e r a t i n g I n s t r u c t i o n s

Maize header

EasyCollect 6000 FP

</v>

(

<v>T - ab Masch.-Nr.</v>

from serial no.

</v>

: 782 200)

<v>T - Bestell-Nr.</v>

Order no.

</v>

: 150 000 055 02 US

<v>B - Titelbild</v> </v>

Foreword

2

Pos: 1 /BA/Ko nformitätserkläru ngen/Vorsätz e/EasyCollect 6 000 FP @ 15\m od_123314122 0679_78.doc @ 179474

CV0

EC Declaration of Conformity

according to EC directive 98/37EC

of June 22, 1998

We Maschinenfabrik Bernard Krone GmbH

Heinrich-Krone-Str. 10, D-48480 Spelle

declare on our sole responsibility that the product

Krone Maize Header

Type: EasyCollect 6000 FP

to which this declaration refers corresponds to the relevant basic safety and health

requirements of the EC Directive 98/37/EC of 22 June 1998.

Spelle, 22.01.09

(Dr.-Ing. Josef Horstmann, Managing Director)

Pos: 2 /BA/Vor wort/Sehr geehrt er Kunde @ 0\ mod_11956263 00326_78.d oc @ 905

Dear customer,

You have now received the operating instructions for the KRONE

product which you have purchased.

These operating instructions contain important information for the

proper use and safe operation of the machine.

If these operating instructions should become wholly or partially

unusable, you can obtain replacement operating instructions for

your machine by stating the number given overleaf.

Pos: 3 /BA/---- -Seitenumbruc h------ @ 0\mod_ 11961753112 26_0.doc @ 4 165

Foreword

3

Pos: 4 /BA/Inhalts verzeichnis Spr achenneutr al @ 10\mod_12 21574899104 _0.doc @ 135 495

1 Foreword ................................................................................................................................................. 7

2 Introduction ............................................................................................................................................. 8

2.1 Purpose of Use .................................................................................................................................. 8

2.2 Validity ............................................................................................................................................... 8

2.2.1 Contact ........................................................................................................................................... 8

2.3 Identification Plate ............................................................................................................................. 9

2.1 Information Required for Questions and Orders................................................................................ 9

2.2 Intended Use ................................................................................................................................... 10

2.3 Technical data ................................................................................................................................. 10

2.3.1 Ballast / forage harvester ............................................................................................................. 10

2.4 Machine overview ............................................................................................................................ 11

3 Safety ..................................................................................................................................................... 13

3.1.1 Identifying Symbols in the Operating Instructions ....................................................................... 13

3.2 Identification of Hazard Warnings .................................................................................................... 13

3.2.1 Personnel Qualification and Training ........................................................................................... 14

3.2.2 Dangers in Case of Non-compliance with the Safety Instructions ............................................... 14

3.2.3 Safety-conscious work practices ................................................................................................. 14

3.3 Safety Instructions and Accident Prevention Regulations ............................................................... 15

3.4 Attached devices ............................................................................................................................. 16

3.5 PTO Operation ................................................................................................................................. 17

3.6 Hydraulic system ............................................................................................................................. 18

3.7 Maintenance .................................................................................................................................... 19

3.8 Unauthorised Conversion/Modification and Spare Parts Production .............................................. 20

3.9 Inadmissible Modes of Operation .................................................................................................... 20

3.10 Introduction ...................................................................................................................................... 21

3.11 Safety Instructions on the Machine ................................................................................................. 21

3.12 Position of the Adhesive Safety Stickers on the Machine ............................................................... 22

3.13 Position of the General Information Labels on the Machine ............................................................ 24

3.13.1 Re-Ordering the Adhesive Safety and Information Labels ...................................................... 25

3.13.2 Affixing the Adhesive Safety and Information Labels .............................................................. 25

4 Start-up -CLAAS ................................................................................................................................... 26

4.1 Stop points ....................................................................................................................................... 27

4.2 Storage ............................................................................................................................................ 27

4.3 Attachment to the CLAAS forage harvester .................................................................................... 28

4.4 Purpose of Use ................................................................................................................................ 28

4.5 Preparations on the forage harvester (type 491, type 492) ............................................................. 28

4.6 Preparations on the forage harvester (type 493, type 494) ............................................................. 29

4.6.1 Preparations on the EasyCollect ................................................................................................. 30

4.7 Coupling ........................................................................................................................................... 31

4.7.1 Type 491, type 492 ...................................................................................................................... 31

Foreword

4

4.7.2 Type 493, type 494 ...................................................................................................................... 33

4.7.3 Connecting the hydraulic lines ..................................................................................................... 35

4.8 Detaching the machine .................................................................................................................... 37

4.8.1 Type 491, type 492 ...................................................................................................................... 39

4.8.2 Type 493, type 494 ...................................................................................................................... 40

5 Start-up – John Deere .......................................................................................................................... 41

5.1 Stop points ....................................................................................................................................... 42

5.2 Storage ............................................................................................................................................ 42

5.3 Mounting on John Deere forage harvesters .................................................................................... 43

5.4 Purpose of Use ................................................................................................................................ 43

5.5 Preparations on Forage Harvester .................................................................................................. 43

5.5.1 Preparations on the EasyCollect ................................................................................................. 44

5.6 Coupling ........................................................................................................................................... 45

5.6.1 Connecting the hydraulic lines ..................................................................................................... 48

5.7 Detaching the machine .................................................................................................................... 50

6 Start-up - New Holland ......................................................................................................................... 53

6.1 Stop points ....................................................................................................................................... 54

6.2 Storage ............................................................................................................................................ 54

6.3 Mounting on New Holland forage harvesters .................................................................................. 55

6.4 Purpose of Use ................................................................................................................................ 55

6.5 Preparations on Forage Harvester .................................................................................................. 55

6.5.1 Series FX (38, 48, 58, 40, 50, 60)................................................................................................ 55

6.6 Preparations on Forage Harvester .................................................................................................. 55

6.6.1 Series FR 90 ................................................................................................................................ 55

6.6.2 Preparations on the EasyCollect ................................................................................................. 56

6.7 Coupling ........................................................................................................................................... 57

6.7.1 Connecting the hydraulic lines ..................................................................................................... 62

6.8 Detaching the machine .................................................................................................................... 65

7 Driving and Transport .......................................................................................................................... 68

8 Operation ............................................................................................................................................... 70

8.1 From transport into working position ............................................................................................... 70

8.1.1 Removing the protective cover .................................................................................................... 70

8.2 Using the Machine for Work ............................................................................................................ 71

8.2.1 Using the maize header ............................................................................................................... 72

8.3 Switching from working position to transport position ..................................................................... 73

8.3.1 Swinging up the maize header .................................................................................................... 73

8.3.1.1 Parking supports in transport position on the right/left ........................................................ 74

8.3.2 Installing guard on the right/left .................................................................................................... 74

8.3.3 Connecting indicators and position lights on the right/left ........................................................... 75

8.3.4 Installing the front guard .............................................................................................................. 75

Foreword

5

9 Settings ................................................................................................................................................. 76

9.1 Adjusting skids ................................................................................................................................. 77

9.2 Adjusting the plant dividers .............................................................................................................. 77

9.3 Adjusting the angle of inclination of the maize header (CLAAS) ..................................................... 78

9.4 Adjusting the angle of inclination of the maize header (John Deere) .............................................. 79

9.5 Adjusting the angle of inclination of the maize header (New Holland) ............................................ 80

9.5.1 Type FX (40,50,60 / 38,48,58) ..................................................................................................... 80

9.6 Block pendulum frame ..................................................................................................................... 81

9.7 Central adjustment of the EasyCollect to the forage harvester for transport .................................. 81

9.8 Adjustment of the compensation springs ......................................................................................... 82

9.9 Change-over gearbox ...................................................................................................................... 83

9.9.1 Moving the PTO shafts on the change-over gearbox .................................................................. 85

10 Maintenance .......................................................................................................................................... 87

10.1 Special Safety Instructions .............................................................................................................. 87

10.1.1 Test run .................................................................................................................................... 87

10.2 Spare Parts ...................................................................................................................................... 87

10.3 Torques ............................................................................................................................................ 88

10.4 Torques (Countersunk Screws) ....................................................................................................... 89

10.4.1 Tightening torques on aluminium gearboxes ........................................................................... 90

10.5 Filling Quantities and Lubrication Designations for Gearboxes ....................................................... 91

10.5.1 Oil Level Check and Oil Change Intervals (Gearboxes) .......................................................... 91

10.5.2 Checking the oil level and changing the oil on the spur wheel gearbox .................................. 92

10.5.2.1 John Deere / New Holland ............................................................................................... 92

10.5.3 Checking the Oil Level and Changing the Oil on the Main Angular Gearbox ......................... 93

10.5.3.1 Claas ................................................................................................................................ 93

10.5.4 Checking the oil level and changing the oil on the transfer gearbox ....................................... 94

10.5.5 Checking the oil level and changing the oil on the angular gearbox ....................................... 96

10.5.6 Checking the oil level and changing the oil on the dresser gearbox ....................................... 98

10.5.7 Checking the Oil Level and Changing the Oil on the Collector Gearbox................................. 99

10.6 Oil level check and oil change on the change-over gearbox ......................................................... 100

10.7 Laid maize worm V-belt (right / left) ............................................................................................... 101

10.7.1 Optional for John Deere and New Holland ............................................................................ 101

10.8 Check the V-belt tension ................................................................................................................ 101

10.9 Correcting the V-belt tension ......................................................................................................... 103

10.10 Checking and adjusting the collector tension ............................................................................ 104

10.11 Adjusting the Scraper ................................................................................................................ 105

10.12 Changing the tips ....................................................................................................................... 106

10.13 Adjusting the tips ....................................................................................................................... 107

10.13.1 Adjusting the side tip .............................................................................................................. 107

10.13.2 Adjusting the central tip ......................................................................................................... 108

Foreword

6

10.14 Removing and installing insertion finger on the collector .......................................................... 108

10.15 Blade Changing ......................................................................................................................... 109

10.15.1 Changing bow and step blades ............................................................................................. 109

10.15.2 Changing the cutting blades .................................................................................................. 111

10.15.3 Changing the scraper blade ................................................................................................... 112

10.15.4 Changing the dresser segments ............................................................................................ 113

10.16 Install the PTO shaft .................................................................................................................. 114

10.17 Friction Clutch ............................................................................................................................ 115

10.17.1 John Deere / New Holland ..................................................................................................... 115

10.18 Hydraulic hose line(s) ................................................................................................................ 116

10.19 Lubrication ................................................................................................................................. 117

10.19.1 Lubrication Chart ................................................................................................................... 117

10.19.2 PTO shafts ............................................................................................................................. 118

10.19.2.1 John Deere .................................................................................................................... 118

10.19.2.2 Claas .............................................................................................................................. 119

10.19.2.3 New Holland ................................................................................................................... 119

11 Placing in Storage .............................................................................................................................. 120

12 Before the Start of the New Season ................................................................................................. 121

12.1 Special Safety Instructions ............................................................................................................ 121

12.2 Test run. ......................................................................................................................................... 122

Pos: 5 /BA/---- -Seitenumbruc h------ @ 0\mod_ 11961753112 26_0.doc @ 4 165

Foreword

7

Pos: 6.1 /Überschrift en/Überschrift en 1/U-Z/Vor wort @ 0\ mod_1195627720 123_78.doc @ 982

1 Foreword

Pos: 6.2 /BA/Vor wort/Vorsätz e/Verehrter Kund e Maisgebiss @ 15\mod_1232 634092971_7 8.doc @ 1752 32

Dear Customer!

By purchasing the maize header, you have acquired a quality product made by KRONE.

We are grateful for the confidence you have invested in us in buying this machine.

It is important to read the operating instructions very carefully before you start operating the

machine to allow you to use the maize header to its full capacity.

The contents of this manual are laid out in such a way that you should be able to perform any

task by following the instructions step by step. It contains extensive notes and information about

maintenance, how to use the machine safely, secure working methods, special precautionary

measures and available accessories. This information and these instructions are essential,

important and useful for the operational safety, reliability and durability of the maize header.

Pos: 6.3 /BA/Vor wort/Vorsätz e/Weiterer Verla uf Maisgebiss @ 15\mod_1232 634230221_7 8.doc @ 1752 55

Note

In the operating instructions which follow the maize header will also be

referred to as the "machine or front attachment".

Pos: 6.4 /BA/Vor wort/Beachten Sie @ 0\mod_ 11956269040 76_78.doc @ 944

Please note:

The operating instructions are part of your machine.

Only operate this machine after you have been trained to do so and according to these

instructions.

It is essential to observe the safety instructions!

It is also necessary to observe the relevant accident prevention regulations and other generally

recognised regulations concerning safety, occupational health and road traffic.

All information, illustrations and technical data in these operating instructions correspond to the

latest state at the time of publication.

We reserve the right to make design changes at any time and without notification of reasons.

Should you for any reason not be able to use these operating instructions either wholly or

partially, you can receive a replacement set of operating instructions for your machine by

quoting the number supplied overleaf.

We hope that you will be satisfied with your KRONE machine.

Maschinenfabrik Bernard Krone GmbH

Spelle

Pos: 7 /BA/---- -Seitenumbruc h------ @ 0\mod_ 11961753112 26_0.doc @ 4 165

Introduction

8

Pos: 8.1 /BA/Ei nleitung/Einleitung @ 0\mod_ 11955624986 77_78.doc @ 416

2 Introduction

These operating instructions contain fundamental instructions. These must be observed in

operation and maintenance. For this reason, these operating instructions must be read by

operating personnel before commissioning and use, and must be available for easy reference.

Follow both the general safety instructions contained in the section on safety and the specific

safety instructions contained in the other sections.

Pos: 8.2 /Überschrift en/Überschrift en 2/U-Z/Ver wendungszw eck @ 1\mod_ 12017072467 38_78.doc @ 54055

2.1 Purpose of Use

Pos: 8.3 /BA/Ei nleitung/Vorsätze /Verwendungsz weck Eas yCollect 6000 FP @ 15\mod_1 233144092929_ 78.doc @ 179 520

The Krone EASYCOLLECT 6000 FP maize header is a harvesting attachment with adapter

frame for attachment to forage harvesters and is used for harvesting maize and other forage

crop with stalks independently of the rows.

Pos: 8.4 /BA/Ei nleitung/Gültigkeit /Vorsätze/Eas yCollect 600 0 FP @ 15\mod_ 12331441563 04_78.doc @ 179543

2.2 Validity

These operating instructions are valid for the maize header

EASYCOLLECT 6000 FP

Pos: 8.5 /Überschrift en/Überschrift en 3/A-E/Ans prechpartner @ 0\mod_1195 569394286_7 8.doc @ 839

2.2.1 Contact

Pos: 8.6 /Adress en/Adresse Mas chinenfabrik KR ONE Spell e @ 0\mod_1195 568531083_7 8.doc @ 734

Maschinenfabrik Bernard Krone GmbH

Heinrich-Krone-Strasse 10

D-48480 Spelle (Germany)

Telephone: + 49 (0) 59 77/935-0 (Head Office)

Fax.: + 49 (0) 59 77/935-339 (Head Office)

Fax.: + 49 (0) 59 77/935-239 (Spare parts - domestic)

Fax.: + 49 (0) 59 77/935-359 (Spare parts - export)

Email: info.ldm@krone.de

Pos: 8.7 /BA/--- --Seitenumbruc h------ @ 0\mod_ 11961753112 26_0.doc @ 4 165

Introduction

9

Pos: 8.8 /Überschrift en/Überschrift en 2/K-O/ Kennzeichnung @ 0\mod_119 5564622099_78 .doc @ 496

2.3 Identification Plate

Pos: 8.9 /BA/Ei nleitung/Kennz eichnung/Eas yCollect 6000 (FP)_ 7500_9000 @ 15\mod_1 232634850799_ 78.doc @ 1753 47

EC200020

1

Fig. 1:

The machine data are specified on the type plate (1).

Pos: 8.10 /BA/Einl eitung/Ang aben für Anfrage und Bestellunge n_Maschnr. @ 9\mod_1220 507505930_7 8.doc @ 1261 10

2.1 Information Required for Questions and Orders

Year

Mach. No.

Type

Note

The entire identification plate represents a legal document and should not be

altered or rendered illegible!

When asking questions concerning the machine or ordering spare parts, be sure to provide type

designation, machine number and the year of manufacture of the relevant machine: To ensure

that these data are always available, we recommend that you enter them in the fields above.

Note

Authentic KRONE spare parts and accessories authorised by the

manufacturer help to ensure safety. The use of spare parts, accessories or

additional equipment not manufactured, tested or approved by KRONE will

exclude any liability for consequential damage.

Pos: 8.11 /BA/---- -Seitenumbruch-- ---- @ 0\ mod_1196175311 226_0.doc @ 4165

Introduction

10

Pos: 8.12.1 /Übersc hriften/Übersc hriften 2/A-E /Bestimmungsge mäßer Ge brauch @ 0\mo d_119640154 5090_78.doc @ 7728

2.2 Intended Use

Pos: 8.12.2 /BA/ Einleitung/Besti mmungsge mäßer Gebrauch/ Vorsätze/Eas yCollect 6000 FP @ 16\mod_1 233144324085 _78.doc @ 17 9589

The Krone maize header EASYCOLLECT 6000, (FP) may only be attached to those carrier

vehicles for which the particular adapter frame has been released (observe operating licence of

the carrier vehicle). It is built exclusively for customary use in agricultural work (intended use) -

also refer to Chapter "Purpose of Use".

Pos: 8.12.3 /BA/ Einleitung/Besti mmungsge mäßer Gebrauch/Nic ht bestim mungs gemäss @ 0\mod_1196 401324340_78.d oc @ 7690

Any use of the machine for other purposes is deemed not to be in accordance with intended

use. The manufacturer shall not be liable for any resulting damage; the user alone shall bear

the risk.

Operation in accordance with intended use also includes observing the operating, maintenance

and service instructions specified by the manufacturer.

Unauthorised modifications to the machine may affect the properties of the machine or disrupt

proper operation. For this reason, unauthorised modifications shall exclude any liability of the

manufacturer for consequential damage.

Pos: 8.13 /BA/Einl eitung/Technis che Daten @ 0\mod_119556 6374865_78.d oc @ 594

2.3 Technical data

All information, illustrations and technical data in these operating instructions correspond to the

latest state at the time of publication. We reserve the right to make design changes at any time

and without notification of reasons.

Pos: 8.14 /BA/Einl eitung/Technis che Daten/V orsätze/EasyColle ct 6000 FP @ 16\mod_123 3144409491_ 78.doc @ 179 613

Type EasyCollect 6000 FP

Length [mm] 2190

Height in working position [mm] 1500

Overall width in working position [mm] 6150

Working width [mm] 6000

Height (folded in) [mm] 3000

Width (folded in) [mm] 2900

Weight [kg] 2800

Power consumption [kW] 40

Drive speed [rpm] 300...700

Max. permitted operating pressure [bar] 200

Hydraulic connections 1xDW*

Electr. connection (lighting) 7-pole

*) DW= Double-action control unit

Pos: 8.15 /BA/Einl eitung/Vorsätz e/Ballastierung /Feldhäcksl er @ 16\mod_ 1233144805382 _78.doc @ 17 9638

2.3.1 Ballast / forage harvester

To ensure safe and reliable operation of the carrier vehicle with the Krone maize header

attached, especially in road traffic, the ballast of the machine must be distributed evenly. Follow

the specifications of the certificate of roadworthiness.

Pos: 8.16 /BA/---- -Seitenumbruch-- ---- @ 0\ mod_1196175311 226_0.doc @ 4165

Introduction

11

Pos: 8.17 /Übersc hriften/Übersc hriften 2/K-O/M aschinenübersi cht @ 0\mod _1195565731 130_78.doc @ 5 55

2.4 Machine overview

Pos: 8.18 /WHB /Allgemeines/Ea syCollect 6000 FP/EasyC ollect FP Voransic ht @ 16\mod _1235645739 337_78.doc @ 1 99944

EasyCollect front view

6

4

11

810

9

WHBEC0080

Fig. 2: EasyCollect front view

(1) Side part (7) Rotating tower

(2) Collector including blades, right (8) Parking support

(3) Tubular bar (9) Cover

(4) Plant divider (10) Insertion finger

(5) Wiper plate (11) Tip

(6) Collector including blades, left

Pos: 8.19 /WHB /Allgemeines/Ea syCollect 6000 FP/EasyC ollect FP Rückansic ht @ 18\ mod_1236932506 097_78.doc @ 207436

EasyCollect rear view

4

2

5

6

WHBEC0081

9

Fig. 3: EasyCollect rear view

(1) Outrigger left (6) Outrigger folding cylinder right

(2) Plant divider

(3) Folding cylinder, plant divider (8) Outrigger folding cylinder left

(4) Outrigger right (9) Transfer gearbox left

(5) Transfer gearbox right

Pos: 9 /BA/---- -Seitenumbruc h------ @ 0\mod_ 11961753112 26_0.doc @ 4 165

Introduction

12

Pos: 10 /BA/Dies e Seite ist be wusst freigelasse n worden. @ 1 \mod_1201 783680373_78. doc @ 54443

This page has been left blank deliberately!!

Pos: 11 /BA/----- Seitenumbruch--- --- @ 0\mod _1196175311 226_0.doc @ 4165

Safety

13

Pos: 12.1 /Übersc hriften/Übersc hriften 1/P-T/ Sicherheit @ 0\ mod_119556 6748646_78.doc @ 635

3 Safety

Pos: 12.2 /BA/Sich erheit/Kennz eichnung von Hi nweisen in d er Betriebsanlei tung Einführungst ext @ 0\ mod_1195637804 826_78.doc @ 1098

3.1.1 Identifying Symbols in the Operating Instructions

The safety instructions contained in this manual which could result in personal injury if not

followed are identified by the general danger sign:

Pos: 12.3 /BA/Sich erheit/Kennz eichnung der G efahrenhin weise @ 0\mod_1 195567454333 _78.doc @ 69 3

3.2 Identification of Hazard Warnings

Danger!

Type and source of the hazard

Effect: Danger to life or serious injuries.

• Measures for hazard prevention

Warning sign

Warning!

Type and source of the hazard

Effect: Danger to life or serious injuries.

• Measures for hazard prevention

Caution!

Type and source of the hazard

Effect: Danger to life or serious injuries.

• Measures for hazard prevention

Pos: 12.4 /BA/Sich erheit/Allge meine Fun ktionshinweise @ 0\mod_11968 69714452_78.d oc @ 15185

General function instructions are indicated as follows:

Note!

Note

Type and source of the note

Effect: Economic advantage of the machine

• Actions to be taken

Instructions which are attached to the machine need to be followed and kept fully legible.

Pos: 12.5 /BA/---- -Seitenumbruch-- ---- @ 0\ mod_1196175311 226_0.doc @ 4165

Safety

14

Pos: 12.6.1 /BA/ Sicherheit/Perso nalqualifikati on und-Schulu ng @ 0\mod_ 1195639383185 _78.doc @ 113 6

3.2.1 Personnel Qualification and Training

The machine may be used, maintained and repaired only by persons who are familiar with it

and have been instructed about the dangers connected with it. The operator must define areas

of responsibility and monitoring of personnel. Should personnel lack the required knowledge,

they must receive the required training and instruction. The operator must ensure that the

contents of these operating instructions have been fully understood by personnel.

Repair work not described in these operating instructions should only be performed by

authorised service centres.

Pos: 12.6.2 /BA/ Sicherheit/Gef ahren bei Nicht beachtung d er Sicherheitshin weise @ 0\mod_ 11956394340 13_78.doc @ 1155

3.2.2 Dangers in Case of Non-compliance with the Safety Instructions

Failure to follow the safety instructions could result in personal injury and environmental

hazards as well as damage to the machine. If the safety instructions are not respected, this

could result in the forfeiture of any claims for damages.

Failure to follow the safety instructions could result, for example, in the following hazards:

• Endangering of persons due to not protected working areas.

• Breakdown of important machine functions

• Failure of prescribed methods for repair and maintenance

• Endangering of persons due to mechanical and chemical effects

• Damage to the environment due to leaking hydraulic oil

Pos: 12.6.3 /BA/ Sicherheit/Sic herheitsbewußt es Arbeiten @ 0\ mod_119563 9792576_78.d oc @ 1174

3.2.3 Safety-conscious work practices

Always observe the safety instructions set out in these operating instructions, all existing

accident prevention rules and any internal work, operating and safety rules issued by the

operator.

The safety and accident prevention regulations of the responsible professional associations are

binding.

The safety instructions provided by the vehicle manufacturer should also be observed.

Observe the applicable traffic laws when using public roads.

Be prepared for emergencies. Keep the fire extinguisher and first aid box within reach. Keep

emergency numbers for doctors and fire brigade close to the telephone.

Pos: 12.6.4 /BA/--- --Seitenumbruc h------ @ 0\ mod_1196175 311226_0.doc @ 4165

Safety

15

Pos: 12.6.5 /BA/ Sicherheit/Sic herheits- und U nfallverhütungs- Vorschriften M aisgebiss @ 15\mod_123269 2324226_78.doc @ 175538

3.3 Safety Instructions and Accident Prevention Regulations

1 Please follow all generally applicable safety and accident prevention regulations in

addition to the safety instructions contained in these operating instructions!

2 The attached warning and safety signs provide important information for safe operation.

Pay attention to these for your own safety!

3 When using public roads, make sure to observe the applicable traffic regulations!

4 Make sure that you are familiar with all equipment and controls as well as with their

functions before you begin working with the machine. It is too late to learn this when you

are using the machine for work!

5 The user should wear close fitting clothes. Avoid wearing loose or baggy clothing.

6 Keep the machine clean to prevent the danger of fire!

7 Before starting or moving the machine, make certain that nobody is in the vicinity of the

machine! (Watch for children!) Make sure that you have a clear view!

8 Carrying passengers during operation and transport on the working implement is not

permitted.

9 Couple implements correctly! Attach and secure implements to specified devices only!

10 When attaching or detaching implements, place the supporting devices in the correct

positions!

11 Special care is required when coupling and uncoupling the maize header onto or from the

forage harvester.

12 Always attach ballast weights properly to the fixing points provided!

13 Observe permitted axle loads, gross weight and transport dimensions!

14 Check and install transport equipment, such as lighting, warning devices and protective

equipment!

15 Actuating mechanisms (ropes, chains, linkage, etc.) for remotely operated devices must

be designed in such a way that, in whatever transport and working position, they cannot

trigger accidental movements.

16 Ensure that the maize header is in the prescribed condition for on-road travel and lock it

in place in accordance with the manufacturer's instructions!

17 Never leave the driver's seat when the vehicle is moving!

18 Always drive at the correct speed for the prevailing driving conditions! Avoid sudden

changes in direction when travelling uphill or downhill or across a gradient!

19 Hitched implements and ballast weights affect the driving, steering and braking response

of the machine. Make sure that you are able to brake and steer the machine as required!

20 Take into account the extension radius and/or inertia of an implement when turning

corners!

21 Take the maize header into operation only after all safety devices have been attached

and are in their proper positions!

22 Keep safety equipment in good condition. Replace missing or damaged parts.

23 Keep clear of the working range of the machine at all times!

24 Do not stand within the turning and swivel range of the implement!

25 Never operate the hydraulic folding frames if anyone is inside the swivel range!

Safety

16

26 Parts operated by external power (e.g. hydraulically) can cause crushing and shearing

injuries!

27 Before leaving the forage harvester, lower the maize header onto the ground, apply the

parking brake, switch off the engine and remove the ignition key!

28 There must be nobody between the forage harvester and the maize header without the

vehicle being secured against rolling away with the parking brake and wheel chocks!

29 Observe all additional information related to safety in the operating instructions for the

forage harvester.

Pos: 12.6.6 /BA/ Sicherheit/Ange baute Gerät e/Geräte angeb aut Maisgebiss @ 15\mod_123 2692548210_ 78.doc @ 175 561

3.4 Attached devices

1 Special care is required when coupling and uncoupling the maize header onto or from the

forage harvester!

2 The maize header must only be attached to the forage harvester for which it is intended.

3 Do not work on the maize header until the engine has been stopped and the ignition key

has been removed. All operating levers should be in the neutral position and no hydraulic

lines should be under pressure.

4 Only perform jobs under the maize header when it is raised if it is securely supported.

Pos: 12.6.7 /BA/ Sicherheit/Ange baute Gerät e/Geräte angeb aut Maisgebiss Z usatz EasyColl ect 6000 FP @ 16\mod_123 3145266116_7 8.doc @ 1796 82

5 On public highways, the maize header (EasyCollect 6000 FP) must always be in

transport position. Attach guard cloths together with flashing lights and front guard to the

maize header and connect the lighting.

Pos: 12.6.8 /BA/--- --Seitenumbruc h------ @ 0\ mod_1196175 311226_0.doc @ 4165

Safety

17

Pos: 12.6.9 /BA/ Sicherheit/Zapf wellenbetrieb V orsätze/Feld häcksler @ 13\ mod_1225450 981661_78.doc @ 156341

3.5 PTO Operation

1 Use only PTO shafts specified by the manufacturer!

2 The guard tube and guard cone of the PTO shaft and the PTO guard must be attached

and in good working condition (on the implement side, too)!

3 Make sure that the required tube covers are in place for PTO shafts in transport and

working position!

4 Before installing or detaching PTO shafts, disengage the PTO, switch off the engine and

remove the ignition key!

5 When using PTO shafts with an overload safety or free-running coupling which are not

shielded by the guard on the tractor, mount the overload safety or free-running coupling

on the implement side!

6 Always make sure that the PTO shaft is properly installed and secured!

7 Attach chains to prevent the PTO shaft guard from rotating with the shaft!

8 Before switching on the PTO, make sure that the selected PTO speed of the forage

harvester matches the permissible speed of the implement!

9 Before switching on the PTO shaft make sure that no person is in the danger zone of the

device!

10 Never switch on the PTO if the engine is switched off!

11 No one should be in the vicinity of the rotating PTO or PTO shaft when the PTO is in use.

12 Always switch off the PTO shaft when the angle is too large or the PTO shaft is not

required!

13 Caution! After disengaging the PTO danger due to the flywheel running on! Keep away

from the implement during this time. Do not work on the machine until it has come to a

standstill.

14 Cleaning, lubricating or adjusting PTO driven implements or the PTO shaft only with PTO

disengaged, engine switched off and ignition key withdrawn!

15 Place the disconnected PTO shaft onto the support provided!

16 After detaching the PTO shaft, attach the protective cover to the PTO end!

17 If damage occurs, correct this immediately before using the implement!

Pos: 12.6.10 /B A/Sicherheit/Za pfwellenbetrieb Z usatz @ 2\m od_12035247 61314_78.doc @ 66513

Note

The instructions of the manufacturer must be observed with regard to the

PTO shaft. (separate operating instructions)

Pos: 12.6.11 /B A/-----Seitenu mbruch------ @ 0\mod_119617 5311226_0.doc @ 4165

Safety

18

Pos: 12.6.12 /B A/Sicherheit/Hydra ulikanlage F eldhäcksler @ 0\mod_1195 646239935_78.d oc @ 1289

3.6 Hydraulic system

1 The hydraulic system is pressurised!

2 When connecting hydraulic cylinders and motors, make sure the hydraulic hoses are

connected as specified!

3 When connecting the hydraulic hoses to the forage harvester hydraulics, take care that

the hydraulic system is depressurised both on the tractor side and on the device side!

4 When functions are connected hydraulically between the forage harvester and the front

attachment, coupling sleeves and plugs should be identified so that faulty operation is

excluded! If the connectors are interchanged, the functions will be reversed (e.g.

raising/lowering) - Risk of accident!

5 Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!

The new hoses must fulfil the technical requirements set by the manufacturer of the

implement!

6 When searching for leaks, use suitable aids to avoid the risk of injury!

7 Liquids escaping under high pressure (hydraulic oil) can penetrate the skin and cause

serious injury! Seek medical help immediately should injuries occur! Meaning of the icons

8 Before working on the hydraulic system, depressurise the system and switch off the

engine!

Pos: 12.6.13 /B A/-----Seitenu mbruch------ @ 0\mod_119617 5311226_0.doc @ 4165

Safety

19

Pos: 12.6.14 /B A/Sicherheit/W artung/Wartung S wadro @ 2\ mod_12035040 22126_78.doc @ 66245

3.7 Maintenance

1 Always make certain that the drive and the engine are switched off before doing any

repairs, maintenance or cleaning! - Remove the ignition key!

2 Regularly check that nuts and bolts are properly seated and tighten if necessary!

3 When performing maintenance work with the machine raised, always secure it with

suitable supporting elements!

4 Oils, greases and filters must be disposed of correctly!

5 Always disconnect the power supply before working on the electrical system!

6 If protective devices and guards are subject to wear, check them regularly and replace

them in good time!

7 When performing electrical welding work on the vehicle and mounted devices, turn power

supply off at main battery switch or disconnect generator cable and battery!

8 Replacement parts must at least comply with the technical requirements set by the

manufacturer of the implements! This is guaranteed by original KRONE spare parts!

Pos: 12.6.15 /B A/Sicherheit/W artung/Wartung Z usatz Schneid wekzeuge @ 1 2\mod_12245 78273531_78.d oc @ 151591

9 When replacing working tools with cutting edges, use suitable tools and gloves!

Pos: 12.6.16 /B A/-----Seitenu mbruch------ @ 0\mod_119617 5311226_0.doc @ 4165

Safety

20

Pos: 12.6.17 /B A/Sicherheit/Eig enmächtiger Um bau und Ers atzteilherstell ung @ 1\mod_12 01937705539 _78.doc @ 55 745

3.8 Unauthorised Conversion/Modification and Spare Parts Production

Conversions or modifications of the machine are permitted only with prior consultation with the

manufacturer. Original spare parts and accessories authorised by the manufacturer help to

ensure safety. Use of other parts may void liability for resulting damage.

Pos: 12.6.18 /B A/Sicherheit/Unz ulässige Betri ebsweisen @ 1 1\mod_12233 57699923_78.d oc @ 14552 7

3.9 Inadmissible Modes of Operation

The operating safety of the delivered machine is guaranteed only when it is used as intended in

compliance with the introductory section "Intended use" of the operating instructions. The limit

values listed in the data charts should not be exceeded under any circumstances.

Pos: 12.7 /BA/---- -Seitenumbruch-- ---- @ 0\ mod_1196175311 226_0.doc @ 4165

Page is loading ...

Krone BA EasyCollect 6000 FP Operating instructions

This manual is also suitable for

Krone BA EasyCollect 6000 FP Operating instructions

Related papers