DreamLine DL-6446C-01CL Installation guide

Vitreo-X Shower Door & Base Kit

SHOWER Door AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

TM

reserves the right to alter, modify or redesign products at any time

without prior notice. For the latest up-to-date technical drawings, manuals or any

other details please refer to the support.BathAuthority.com web page.

STEP 1: Install Shower Base

Shower Base Installation Instructions

STEP 2: Install Shower Door

Shower Door Installation Instructions

Please read these instructions carefully before installing. If you have any questions regarding

installation, please call our technical support specialists Monday through Friday 9:00 AM – 5:00

PM EST at Phone: 1-866-731-2244, Fax: 1-866-227-1533 or e-mail our technical support

group at

[email protected].

For more information on DreamLine Shower Kit please visit www.BathAuthority.com

VITREO X

SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

TM

reserves the right to alter, modify or redesign products at any time without prior

notice. For the latest up-to-date technical drawings, manuals or any other details please refer

to the support.BathAuthority.com web page.

Please read these instructions carefully before installing. If you have any questions regarding

installation, please call our technical support specialists Monday through Friday 9:00 AM – 5:00

PM EST at Phone: 1-866-731-2244, Fax: 1-866-227-1533 or e-mail our technical support group

at

[email protected].

For more information on DreamLine

TM

Shower Doors & Tub Doors please visit www.BathAuthority.com

“VITREO X” Rev.3 Ver.2 03/2014 2

Preparation

1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed

parts are included in the package by marking all the components on the “Detailed Diagram of

Shower Door Components”. Examine boxes and packages for shipping damage. If the unit has

been damaged, has a finishing defect, or is missing parts, please contact our customer support

department within 5 business days of the delivery date. Please note that DreamLine

TM

will not

replace any damaged products or missing parts free of charge after 5 business days or if the

product has been installed. Feel free to contact DreamLine

TM

if you have any questions.

2. Please note that you should consult your local building codes with questions on installation

compliance standards. Building and plumbing codes may vary by location, and DreamLine is

not responsible for code compliance standards for your project and will not accept any

returns.

3. If this unit is going to be installed in a new construction, please, install all of the required plumbing

and drainage before installing the shower. Use a competent and licensed (if required by local

code) plumber for all plumbing installation period.

4. Prior to installation, please ensure that the installation surface is level and solid and will be able to

support the total weight of the unit. Also, make sure that the walls are plumb. Depending on the

type of unit you are installing, some adjustments in leveling may be possible. However, irregular

installation, surface level or out of square conditions can result in serious problems for your

installation. Please note that some adjustments and drilling may be necessary. Please protect all

primary surfaces of the product during installation. Never set your glass down directly onto a

tile floor. Always use a piece of wood or cardboard to protect the bottom edge and corners of

the glass.

5. Please, NOTE! This door has 3/8” out-of-plumb adjustment on each side. Make sure your

walls are at right angles.

Tools Required

Caulk

Tape

Measure Pencil

Screwdriver

Phillips

(Ø=5/16")

Drill bit

Level

Gun

Caulk

Drill

Electric

Hammer

Mallet

Wood

(Ø=1/8")

Drill bit

Knife

“VITREO X” Rev.3 Ver.2 03/2014 3

Detailed Diagram of Shower/Tub Door Components

3

4

5

19

6

7

10

11

12

13

14

15

16

17

18

1

2

8

9

Packing List

01 Glass profile 2pcs 11 Bottom anti-water strip 1pc

02 Wall profile 2pcs 12 Flanged anti-water strip 1pc

03 Stationary glass 2pcs 13 Vinyl gasket 4pcs

04 Glass door 1pc 14

Hex socket bolt M8×12

4pcs

05 Pivot bar 2pcs 15

Hex socket bolt M8×25

4pcs

06 Wall anchor 8pcs 16 Decorative washer 4pcs

07 Big flat head screw ST4.2×40 8pcs 17 Allen key 1pc

08 Round head screw ST4.2×10 4pcs 18 Pivot assembly 2pcs

09 Decorative cover 4pcs 19 Handle 1pc

10 Magnetic strip 2pcs

NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using detailed

diagram and packing list in your manual as a reference. Before discarding the carton, check for small

hardware bags that tend to fall to the bottom of the box. If any parts are damaged or missing, please

contact DreamLine

TM

for replacement.

NOTE: Retain these installation instructions for future reference.

“VITREO X” Rev.3 Ver.2 03/2014 4

Shower/Tub Door Installation

Attention: This shower/tub installation is true for both equal and variable width stationary glass

panels. The position for variable width stationary glass panels should be determined in accordance

to the installation situation. “Flipping” the glass horizontally will allow the glass to be positioned

on either side of the shower or tub.

1. Apply clear silicone along the inner channel of the Glass

profile (01) and push the Stationary glass (03) inside the

channel.

Slide the Stationary glass assembly into the groove of the

Wall profile (02).

NOTE: The small holes on the Stationary glass should be

away from the wall and facing the door opening.

NOTE: If you have difficulty sliding the Glass profile over the

Stationary glass, you can slightly tap on the Glass profile with

a rubber mallet and a piece of wood. Please do not strike

directly on the profile or on the edge of the glass panel.

See Fig. 1 and Fig. 2 for details.

Fig. 1

Fig. 2

1

2

3

4

5

6

“VITREO X” Rev.3 Ver.2 03/2014 5

2. Place the Wall profile (02) to the wall above the

shower base or tub and level it vertically.

See Fig. 3 for details.

Fig. 3

3. Make sure the Wall profile (02) is absolutely vertical.

Mark the drilling holes on the wall through the predrilled

holes in the Wall profile.

Drill the holes in the wall using Ø 5/16” drill bit and

insert the Wall anchors (06).

Run a bead of waterproof silicone along the back of the

Wall profile.

Fasten the Wall profile to the wall using the Big flat

head screw ST4.2×40 (07).

See Fig. 4 for details.

Fig. 4

1

2

3

4

5

Ø5/16"

“VITREO X” Rev.3 Ver.2 03/2014 6

4. Place the other Wall profile (02) to the opposite wall

above the shower base or tub and level it vertically.

Please note that this Wall profile must be aligned

perfectly with the opposite Wall profile on the threshold.

Mark the drilling holes on the wall through the predrilled

holes in the Wall profile.

Drill the holes in the wall using a Ø 5/16” drill bit and

insert the Wall anchors (06).

Run a bead of waterproof silicone along the back of the

Wall profile.

Fasten the Wall profile to the wall using the Big flat

head screw ST4.2×40 (07).

See Fig. 5 for details.

Fig. 5

5. Insert the assembled Stationary glasses (03) into the Wall profiles

(02).

See Fig. 6 and Fig. 7 for details.

Fig. 6

1

2

3

4

5

Ø5/16"

1

2

“VITREO X” Rev.3 Ver.2 03/2014 7

Fig. 7

6. Please orient the Pivot assembly (18) holes in the Pivot bars

according to the desired swing of the door.

Attach top and bottom Pivot bars (05) to the Stationary glass (03)

using clear Rubber spacers (13), Decorative washers (16) and Hex

socket bolts M8×25 (15). Place the clear Rubber spacers between

the Pivot bar and the Stationary glass to prevent glass to metal

connection.

Place the Decorative washer between the Hex socket bolts M8×25

and the Stationary glass.

See Fig. 8 for details.

Fig. 8

1

2

Inside

“VITREO X” Rev.3 Ver.2 03/2014 8

7. The Pivot assemblies (18) ship in pairs

as one for the top and one for the

bottom. Position correctly for the

outward swing of the door.

Mount top and bottom Pivot

assemblies to the Pivot bars (05)

using Hex socket bolts M8×12 (14).

Remove the back fastener from the

pivot assemblies. Set the Glass door

(04) so the holes are aligned. Make

sure the rubber gaskets are in between

the glass and the metal parts. Secure

the back fastener with the provided

bolt.

See Fig. 9 and Fig. 10 for details.

Fig. 9

Fig. 10

1

2

3

Inside

“VITREO X” Rev.3 Ver.2 03/2014 9

8. Push the Flanged anti-water strip

(12) to the vertical edge of the

Glass door (04) to seal between

the door and the Stationary glass

(03).

Push the Bottom anti-water strip

(11) to the bottom edge of the

Glass door.

Push the Magnetic strips (10) to

the vertical edges of the Glass

door and the Stationary glass.

See Fig. 11 for details.

Fig. 11

9. After final adjustments of both Stationary glass (03),

panels, drill holes through the pre-drilled holes in

both of the Wall profiles (02) into the first layer of

the Glass profiles (01) using Ø 1/8” drill bit.

Use the Round head screws ST4.2×10 (08) to secure

the Glass profiles inside the Wall profiles. Use the

raised white washer with the screw and attach the

Decorative Covers (09).

See Fig. 12 for details.

Fig. 12

1

2

3

4

5

6

Ø1/8"

1

2

4

3

Inside

Glass door

pivot side

Inside

“VITREO X” Rev.3 Ver.2 03/2014 10

10. Apply a bead of waterproof silicone along the bottom

edges of the Stationary glass (03) and Pivot bars

(05).

See Fig. 13 for details.

Fig. 13

Product Maintenance

To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean

the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal

brushes or scrapers that could scratch or dull the surface.

To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse

and wipe off the glass using either soft cloth or squeegee to prevent soap buildup. Never use abrasive cleaners

and cleaning products that contain scouring agents as this may scratch the surface. Never use bristle brushes or

abrasive sponges.

To ensure a long lasting hardware finish, wipe off the metal parts after each use with a soft cloth. Do not use

abrasive cleaners or cleaning products containing ammonia, bleach or acid. If accidentally used, rinse the

surface as soon as possible to prevent finish peeling or corrosion. After cleaning the shiny finishes, rinse

thoroughly and wipe dry with soft cloth. Clean stainless steel surfaces at least once a week. When applying

stainless steel cleaner or polish, work with (not against) the grain. Never use an abrasive sponge or cloth, steel

wool or wired brushes.

SLIMLINE SHOWER BASE

SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS

IMPORTANT

DreamLine

TM

reserves the right to alter, modify or redesign products at any time without

prior notice. For the latest up-to-date technical drawings, manuals or any other details

please refer to your model’s web page on BathAuthority.com

Please read these instructions carefully before installing. If you have any questions

regarding installation, please contact our technical support specialists Monday

through Friday 8:00 AM – 7:00 PM EST at: Phone: 1-866-731-2244, Fax: 1-866-857-

3638 or e-mail our technical support group at Support@BathAuthority.com

For more information on DreamLine

TM

Shower Bases please visit www.BathAuthority.com

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

2

Preparation

1. Prior to installation, examine all boxes and packages for shipping damage and compare the

piece count with your packing slip. After opening all boxes and packages, read this introduction

carefully. Check that all of the needed parts are included in the package by checking off the

components on the “Detailed Diagram of Shower Door Components”. If the unit has been

damaged, has a finishing defect, or has missing parts, please contact our customer support

department within 5 business days of the delivery date. Please note that DreamLine

TM

will not

replace any damaged products or missing parts free of charge after 10 business days or if

the product has been installed. Feel free to contact DreamLine

TM

if you have any questions,

and please provide an order number, job name or other proof of purchase to help us identify

your original order.

2. Install all of the required plumbing and drainage before installing the shower base. Use a

competent and licensed (if required by local code) plumber for all plumbing installation.

3. Shower bases must be installed by a licensed plumber. Please note that you should

consult your local building codes with questions on installation compliance standards.

Building and plumbing codes may vary by location, and DreamLine is not responsible for

code compliance standards for your project.

4. Please insure that prior to the installation the installation surface is leveled and solid and will be

able to support the total weight of the unit. Also make sure the walls are at right angles. While

some adjustment in leveling of the tray is possible, irregular installation surface level or

improper angle of side walls will result in serious problems for your installation. Please, note

that some adjustments may be necessary during the installation process.

IMPORTANT NOTE: Dimensions provided are for reference only. You must

measure the actual shower tray sizes before installation, this includes overall

dimensions and drain location. Allowed tolerance for center of the drain is

±1/2".

Tools Required

XXX

Tape

Measure

Pencil

Level

Mortar

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

3

SINGLE THRESHOLD SHOWER BASE

Center Drain Configuration

MODEL

SPECIFICATION

D (in)

W (in)

D1 (in)

W1 (in)

DLT-1132320

32"×32"

32"

15"

16"

DLT-1136360

36"×36"

36"

15"

18"

DLT-1134420

34” x 42”

34”

42”

15”

21”

DLT-1132480

32"×48"

32”

48”

15”

24”

DLT-1136480

36"×48"

36"

48"

15"

24"

DLT-1130600

30"×60"

30"

60"

15"

30"

DLT-1132600

32"×60"

32"

60"

15"

30"

DLT-1134600

34"×60"

34"

60"

15"

30"

DLT-1136600

36"×60"

36"

60"

15"

30"

W

D

W1

11

D1

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

4

SINGLE THRESHOLD SHOWER BASE

Left-Hand Drain Configuration

MODEL

SPECIFICATION

D (in)

W (in)

D1 (in)

W1 (in)

DLT-1130601

30"×60"

30"

60"

15"

12"

DLT-1132601

32"×60"

32"

60"

15"

12"

DLT-1134601

34"×60"

34"

60"

17"

12"

DLT-1136601

36"×60"

36"

60"

18"

12"

W

D

D1

W1

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

5

SINGLE THRESHOLD SHOWER BASE

Right-Hand Drain Configuration

MODEL

SPECIFICATION

D (in)

W (in)

D1 (in)

W1 (in)

DLT-1130602

30"×60"

30"

60"

15"

12"

DLT-1132602

32"×60"

32"

60"

15"

12"

DLT-1134602

34"×60"

34"

60"

17"

12"

DLT-1136602

36"×60"

36"

60"

18"

12"

W1

W

D

D1

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

6

NEO ANGLE SHOWER BASE

MODEL

SPECIFICATION

W (in)

A (in)

B (in)

C (in)

DLT-2036360

36"×36"

36"

18 5/16"

25"

12"

DLT-2038380

38"×38"

38"

20 5/16"

25"

12"

DLT-2040400

40"×40"

40"

22 5/16"

25"

14 3/8"

DLT-2042420

42"×42"

42"

24 5/16"

25"

14 3/8"

W

A

C

B

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

7

QUARTER ROUND SHOWER BASE

MODEL

SPECIFICATION

W (in)

C (in)

R (in)

DLT-7033330

33"×33"

33"

12"

21 5/8"

DLT-7036360

36"×36"

36"

12"

21 5/8"

DLT-7038380

38"×38"

38"

12"

21 5/8"

W

C

R

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

8

DOUBLE THRESHOLD SHOWER BASE

Corner Drain Configuration

MODEL

SPECIFICATION

W (in)

C (in)

DLT-1032320

32"×32"

32"

12"

DLT-1036360

36"×36"

36"

12"

W

C

“SLIMLINE SHOWER BASE” Ver.5 Rev.5 06/2015

9

DOUBLE THRESHOLD SHOWER BASE

Left-Hand Drain Configuration

MODEL

SPECIFICATION

D (in)

W (in)

D1 (in)

W1 (in)

DLT-1034481

34"×48"

34"

48"

17"

12"

DLT-1036481

36"×48"

36"

48"

18"

12"

DLT-1036601

36"×60"

36"

60"

18"

12"

D

W

D1

W1

Page is loading ...

DreamLine DL-6446C-01CL Installation guide

This manual is also suitable for

DreamLine DL-6446C-01CL Installation guide

Related papers

Other documents