Kichler Lighting 15191BK User manual

Brand: Kichler Lighting

Model: 15191BK

Type: User manual

Kichler Lighting 15191BK is a low voltage outdoor lighting fixture, ideal for illuminating ponds, fountains, and landscapes. With a maximum depth of 6 feet, it's suitable for various water features. It utilizes energy-efficient LED technology and is compatible with Kichler's low voltage lighting power units (transformers) rated at a maximum of 15 volts, 300W per secondary (25 AMPS). The fixture features a durable housing, a clear glass lens for optimal light distribution, and an O-ring for a secure, watertight seal.

WARNING – RISK OF ELECTRIC SHOCK

• Use only in ponds and small decorative fountains where persons will

immerse no more than their hands and lower arms while the product

is energized.

• DO NOT use in water intended for swimming, wading, immersion, or

bathing.

• All installer completed cable connections must be located outside of

pond or fountain.

• Low voltage circuit must be supplied by a power unit marked as

suitable for supplying submersible luminaires.

• Power unit must be supplied by a branch circuit protected by a Class A

type ground fault circuit interrupter (GFCI).

• Maximum Depth: 72” (1.8m)

• Do not mount luminaire within 10 feet (3m) of a swimming pool, spa or

fountain.

• This xture is to be used only with a Kichler low voltage lighting power

unit (transformer) rated a maximum 15 volts, 300 W per secondary (25

AMPS).

• According to the requirements of the National Electric Code (NEC),

direct burial rated wire is to be buried a minimum of 6” [152mm]

beneath the surface of the ground.

NOTE: If additional Direct Burial wire is needed, contact your local

Kichler

landscape distributor.

• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.

• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.

• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK;

250’ (76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M),

15506-BK.

• Fixture shall not use a tungsten halogen lamp unless the xture is

markedfor use with such lamps.

• Wiring connections must be made with approved/listed wire connection

device(s) suitable for the application. Do not exceed manufacturers’

wiring combination specications for size and quantity of conductors.

FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.

1) The device is accepted as a component of a landscape lighting system

where the suitability of the CSA or UL labeled combination shall be

determined by CSA, UL respectively or the local inspection authorities

having jurisdiction.

2) Fixture shall be connected to an extra low voltage transformer ap

proved for use with landscape lighting systems.

3) This xture is to be connected to a secondary wiring of the following type:

12 GA 60°C minimum type;

SPT-3 suitable for outdoor use; or

approved landscape lighting cable.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO PER-

SONS

IMPORTANT SAFETY INSTRUCTIONS

Lighted lamp is HOT!

WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.

1) Turn off / unplug and allow to cool before replacing lamp.

2) Lamp gets HOT quickly! Contact only switch / plug when turning on.

3) Do not touch hot lens or cowl.

4) Do not remain in light if skin feels warm. (Light is intense, it may cause

“sunburn”.)

5) Do not look directly at lighted lamp.

6) Keep lamp away from materials that may burn.

7) Use only with wattage and lamp marked on xture.

8) Do not touch the inner glass envelope of the lamp at any time. Use a soft

cloth. Oil from skin may damage lamp.

9) Do not operate the xture with a damaged or missing lens.

ASSEMBLY AND INSTALLATION

1) Twist cover counter clock-wise and remove.

2) Remove lens.

3) Insert recommended lamp into socket.

NOTE: Use caution when installing. Hold lamp by outer housing. DO

NOT touch glass envelope inside. If this happens, clean lamp with

denatured alcohol and a lint free cloth.

4) Reassemble lens and cover to housing. Turn cover until it snaps into

place.

NOTE: If O-Ring comes out during assembly, lay O-Ring on ledge

inside of housing before assembling. Do not assemble without O-Ring

in place.

5) Turn off power.

6) Make wire connections directly to a low voltage transformer or connect to

low voltage power supply cable using the appropriate connectors.

Connection from the xture cable to power supply cable should not be

submerged. (Connectors sold separately.)

7) Support base and adjust housing to desired direction.

8) Submerge xture.

Date Issued: 7/29/11 IS-15191-CB

OUTDOOR USE ONLY

DOM ETRE INSTALLE A L’EXTERIEUR

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

COVER

COUVERCLE

O-RING

JOINT TORIQUE

LENS

VERRE DIFFUSEUR

LAMP

L’AMPOULE

HOUSING

BOÎTIER

BASE

For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page

Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page

Kichler Lighting 15191BK User manual

Kichler Lighting 15191BK User manual

Kichler Lighting 15191BK User manual

Related papers

Other documents