We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
IS-45706LED-US
FCC Information:
This device complies with part 15 of the FCC Rules. Operaon is
subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. However,
there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to
radio or television recepon, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
DIMMING: This LED xture is compable with most standard
incandescent dimmers, LED dimmers, and electronic low voltage
dimmers. For opmal performance, an electronic low voltage
dimmer should be used.
CLEANING: Always be certain that electric current is turned o
before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products
may damage the nish.
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Instrucons:
1) Remove (4) Mounng Screws[G].
2) Slide mounng plate[A] out of xture canopy[E].
3) Aach the mounng plate to the outlet box[C] with
supplied strap mounng screws[B].
4) Grounding instrucons: (See Illus. I or II)
a. On xtures where mounng plate is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b. On xtures where a cupped washer is provided.
Put ground wire from outlet box under cupped
washer and green ground screw and thread screw
into hole inmounng strap.
Fixture Diagram
Parts List
[A] Mounting
Plate
[B] Strap
Mounting
Screws
[C] Outlet Box
[D] Wire
Connections
[E] Canopy
[F] Glass
[G] Mounting
Screws
[H] Decorative
Studs
[I] Glass Bracket
Cauons
If xture is provided with ground wire. Connect xture
ground wire to outlet box ground wire with wire con-
nector, aer following the above steps. Never connect
ground wire to black or white power supply wires.
5) Make wire connecons. Reference chart below for correct
connecons and wire accordingly.
5) Fixture can be mounted up, down or horizontal.
Determine which orientaon and place xture up to
mounng plate. Carefully push wire connecons[D]
inside mounng plate and canopy making sure all
connecons remain secure and wires do not get pinched.
6) Insert and ghten mounng screws to secure xture to
wall.
7) Install the glass[F] into the main xture.
8) Place the glass bracket[I] over the glass and using the
two (2) decorave studded knobs[H]; secure the bracket
in place.
A
C
D
B
H
G
E
F
I
Page is loading ...
Page is loading ...
/
