American DJ Supply
4295 Charter Street
Los Angeles Ca. 90058
(323) 582-2650 (323) 582-2610
www.americandj.com
User Instructions
Congratulations and thank you for purchasing the American DJ Marvel™.
The Marvel™ is one of the finest pieces of its kind on the market
today. This unit use a single color/gobo wheel combination for vibrant
colors and extravagant gobo patterns. The Marvel™ is a semi intel-
ligent fixture that can run as a stand alone sound active piece or in a
Master/Slave mode. This fixture is sound active and can be linked via
XLR cables up to 16 pieces. The Marvel™ comes with several build in
programs that are best used in multiples of four or more. The Marvel™
also offers you the ability to run with a standard DMX controller. This
piece is best used with a fog or haze machine. The Marvel™
comes
with a swivel mirror that gives the allusion of X / Y movement, this mir-
ror can be adjusted by hand. The Marvel™ can operate in any of three
modes; Stand alone, Master/Slave, or DMX, these will be explained
later in this manual. An optional Marvel/C controller may be pur-
chased separately that allows the user to Black Out the Marvel™ when
used in stand-alone or master/slave modes. This unit is extremely light
weight and compact which makes it perfect for mobile DJs, but is also
great for small club, bars, bowling centers and roller rinks.
Customer Support:
American DJ provides a toll free customer support line, to provide set
up help and to answer any question should you encounter problems
during your set up or initial operation. You may also visit us on the web
at www.americandj.com for any comments or suggestions.
Service Hours are Monday through Friday 10:00 a.m. to 5:00 p.m.
Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2610
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 2
HALOGEN LAMP WARNING!
This fixture is fitted with a halogen lamp which is highly susceptible
to damage if improperly handled. Never touch lamp with your bare
fingers as the oil from your hands will shorten lamp life. Also, never
move the fixture until the lamp has had ample time to cool. Remember,
lamps are not covered under warranty conditions.
Marvel™ Introduction
Caution!
There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufac-
tures warranty. In the unlikely event your unit may require service,
please contact your nearest American DJ dealer.
Warning!
To prevent or reduce the risk of electrical shock or re, do not expose
this unit to rain or moisture. Clearing memory often may cause damage
to the memory chip, be careful not to re initialize your unit frequency
often to avoid this risk. Only use the recommended AC/DC power adap-
tor.
Power Supply: Before plugging your unit in be sure the source
voltage in your area matches the required voltage for your American
DJ® Marvel.™ The Marvel™ is available in a 115v and 230v version.
Because line voltage may vary from venue to venue, you should be sure
to plug your power supply into a matching wall outlet before attempting
to operate you controller.
Data Cable (DMX Cable) Requirements:
Your xture and your controller require a
standard 3-pin XLR connector for data
input and data output (Figure 1). If you
are making your own cables be sure to
use standard two conductor shielded cable
(This cable may be purchased at almost all
pro sound and lighting stores). Your cables
should be made with a male and female
XLR connector on either end of the cable.
Also, remember that DMX cable must be
daisy chained and can not be “Y”ed or split.
Figure 1
Figure 2
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 IN
(X-CALIBUR)
CONNECTOR
3 PIN
DMX512 OUT
CONTROLLER
CONNECTOR
3 PIN
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 3
XLR MALE SOCKET
1 EARTH
2 COLD
HOT
XLR FEMALE SOCKET
1 EARTH
COLD 2
3 HOT
XLR Pin Configuration:
Pin 1 = Shield
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination.
When longer runs of cable
are used, you may need to use a terminator on the last unit to avoid
erratic behavior. A terminator is a 90 - 120 ohm 1/4 watt resistor which is
connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 IN
(X-CALIBUR)
CONNECTOR
3 PIN
DMX512 OUT
CONTROLLER
CONNECTOR
3 PIN
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 4
Linking:
Your Marvel comes with built in programs. These programs will auto-
matically run to the beat of music. For a more dramatic effect link sev-
eral Marvel units together. Each Marvel can act a “Master Unit” that
can control up to 15 more units. Link the units together using standard
DMX cable. Follow the Master/Slave Dip Switch Chart on page 7 for
proper dip switch settings. The built programs are optimized for a four
unit chase.
Warranty:
The American DJ Marvel™ comes with a one (1) year limited warranty.
We recommend filling out the warranty registration card that came with
your fixture to validate your warranty. You may also fill out a product
registration form on-line at www.americandj.com.
Notice: Do not use the ground lug on the XLR connector. Do
not connect the cable’s shield conductor to the ground lug or allow
the shield conductor to come in contact with the XLR’s outer casing.
Grounding the shield could cause a short circuit and erratic behavior.
Figure 4
Marvel™ Set-UP Marvel™ Set-UP
3
follow the dip switch settings on page 8. If starting at a higher
DMX channel follow the standard DMX Binary Code for a two (2)
channel unit.
6. For help running in DMX operation consult the manual that comes
with your DMX controller.
7. For longer cable runs we suggest using a terminator on the last
fixture.
The 1/4” phone plug on the unit is for the optional Marvel/C. Do
not attempt to connect an audio signal this jack, this will damage
the PC board and void your manufactures warranty!
Lamp Replacement: Caution! To avoid the risk of electrical shock
or injury never attempt to open up the unit while it is in use. Always
disconnect the main power before attempting to replace the lamp or
fuse. Remember to always replace with the exact same type lamp and
fuse unless otherwise instructed to do so by an authorized American
DJ service technician.
1. Be sure to follow the proper procedures when handling halogen
bulbs.
2. Loosen the screw on trap door located on top of the unit.
3. Remove the trap door.
4. Remove and replace the bulb.
5. Reassemble.
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment
in which the fixture operates (i.e. smoke, fog residue, dust, dew).
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Use a brush to wipe down the fan grill and remove as much
built up as possible.
3. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth
every 30-60 days.
5. Always be sure to dry all parts completely before plugging the
unit in.
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 6
Stand Alone:
1. This function allows a single unit to run to the beat of the music.
Only use this function when running a single unit or when running
more than one unit as an individual.
2. To activate this mode set dip switches #1 and #10, on the front of
unit to the ON position (See master fixture on the DIP SWITCH
chart on page 4).
3. Plug the unit in, the unit will react to sound via its own internal
microphone.
4. The optional Marvel/C controller may be used with this function
for blackout.
Master / Slave Operation:
1. This function allows you to set up several units to operate without
a controller.
2. The units will be sound activated and will run built in programs via
an internal microphone.
3. To activate this function set one unit, the master unit, dip switches
as followed: Set dip switches #1 and #10 to the on position (see
the chart on page 7).
4. For additional units (slaves), up to 16 units total, follow the chart
on page 7.
5. Connect the units together via XLR cables remembering that the
Male XLR socket is IN
and the Female XLR socket is OUT.
6. The optional Marvel/C controller may be used for black out.
7. For longer cable runs we suggest a terminator at the last fixture.
Universal DMX Control:
1. This function allows you to use a standard DMX controller such as
the American DJ Show Designer™.
2. The use of a DMX controller will allow you to customize the use
of fixtures allowing you independent control of the colors, mirror,
and the ability to black out.
3. This will allow you to create your own programs.
4. The Marvel™
is a DMX two channel fixture; channel one
controls the color and shutter, channel two controls the mirror
movement.
5. When using a DMX controller and setting up for DMX operation
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 5
Marvel™ Operation Marvel™ Operation
DIP SWITCH SETTINGS FOR DMX MODE
The following chart details the Marvel™ DMX dip switch setting for the first
16 fixtures in DMX mode.
1 2
43 5 6
HEAD 1
7 8 9
1 2
43 5 6
HEAD 3
7 8 9
1 2
43 5 6
HEAD 4
7 8 9
1 2
43 5 6
HEAD 2
7 8 9
10
ON
ON
ON
ON
10
10
10
1 2
43 5 6
HEAD 6
7 8 9
1 2
43 5 6
HEAD 8
7 8 9
1 2
43 5 6
HEAD 9
7 8 9
1 2
43 5 6
HEAD 7
7 8 9
10
ON
ON
ON
ON
10
10
10
1 2
43 5 6
HEAD 11
7 8 9
1 2
43 5 6
HEAD 13
7 8 9
1 2
43 5 6
HEAD 14
7 8 9
1 2
43 5 6
HEAD 12
7 8 9
10
ON
ON
ON
ON
10
10
10
1 2
43 5 6
HEAD 5
7 8 9
ON
10
1 2
43 5 6
HEAD 10
7 8 9
ON
10
1 2
43 5 6
HEAD 15
7 8 9
ON
10
1 2
43 5 6
HEAD 16
7 8 9
ON
10
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 8
DIP SWITCH SETTINGS FOR SOUND
ACTIVE MODE (MASTER/SLAVE)
The following chart details the Marvel™ dip switch setting for up to 16 fixtures
in a Master/ Slave mode.
1 2
43 5 6
MASTER - HEAD 1
7 8 9
1 2
43 5 6
HEAD 3
7 8 9
1 2
43 5 6
HEAD 4
7 8 9
1 2
43 5 6
HEAD 2
7 8 9
10
ON
ON
ON
ON
10
10
10
1 2
43 5 6
HEAD 6
7 8 9
1 2
43 5 6
HEAD 8
7 8 9
1 2
43 5 6
HEAD 9
7 8 9
1 2
43 5 6
HEAD 7
7 8 9
10
ON
ON
ON
ON
10
10
10
1 2
43 5 6
HEAD 12
7 8 9
1 2
43 5 6
HEAD 14
7 8 9
1 2
43 5 6
HEAD 15
7 8 9
1 2
43 5 6
HEAD 13
7 8 9
10
ON
ON
ON
ON
10
10
10
1 2
43 5 6
HEAD 5
7 8 9
ON
10
1 2
43 5 6
HEAD 10
7 8 9
ON
10
1 2
43 5 6
HEAD 16
7 8 9
ON
10
1 2
43 5 6
HEAD 11
7 8 9
ON
10
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 7
Marvel™ DMX Dip Switch Settings Marvel™ Master/Slave Dip Switch Settings
The Marvel™ uses two DMX channels to
operate properly. Channel one (1) con-
trols the Gobo/Color combination wheel
and channel two (2) controls the mirror
rotation.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Marvel Gobo Wheel Layout
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 10
Channel 1
Gobo 17
Gobo 16
Gobo 18
Gobo 1
Gobo Scroll
270˚
180˚
90˚
0˚
Mirror Rotation
Channel 2
Gobo 15
Gobo 14
Gobo 13
Gobo 12
Gobo 11
Gobo 10
Gobo 9
Gobo 7
Gobo 8
Gobo 6
Gobo 5
Gobo 4
Gobo 3
Gobo 2
Gobo 1
Blackout
Gobo / Color
Value
128
120
112
104
96
88
80
72
64
56
48
40
32
24
16
8
0
160
152
144
136
Rotation
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 9
Strobe
192
Marvel™ DMX Traits
Model: Marvel™
SPECIFICATIONS:
Voltage: 120V / 220V
Lamp: ELC-3 24v/250w
Dimensions: 14.25” x 6.5” x 6”
Weight: 17 lbs.
Fuse: 7A
Working Position: Any safe position
Cooling: Fan Cooled
Duty Cycle: 30 min. ON, 10 min. OFF
Gobos: 17 Plus large & small spot
Colors: Multi Colors/Split Colors
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 12
DMX CHANNEL
1 2 3 54 7 9 1086
ON
1 4 16 64 256
2 8 32 128
DMX means Digital Multiplex. This is a universal binary language used to
control intelligent lighting fixtures. Each dip switch number has an ADDRESS
based on binary code:
Dip Switch 1 address equals 1
Dip Switch 2 address equals 2
Dip Switch 3 address equals 4
Dip Switch 4 address equals 8
Dip Switch 5 address equals 16
Dip Switch 6 address equals 32
Dip Switch 7 address equals 64
Dip Switch 8 address equals 128
Dip Switch 9 address equals 256
Dip Switch 10 is used to control the Master/Slave operation. Turning dip
switch 10 on will activate that unit as a “Master Unit.”
©American DJ Supply® www.americandj.com Marvel Instruction Manual Page 11
DMX Channel Value
Marvel™ DMX Addressing
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American DJ rotogobo User Instructions
-
-
-
-
-
-
-
-
-
Other documents
-
ACME MH-640S-ELC User manual
-
ACME MH-600A Mobile Color User manual
-
Martin Wizard User manual
-
ADJ CENTURION User manual
-
-
-
-
-
-
ELM Video DX10V User guide