Vector GL3000 series User manual

User Manual

GL3000/GL4000 Series

Version

2.4

English

Imprint

Vector Informatik GmbH

Ingersheimer Straße 24

D

-70499 Stuttgart

Vector reserves the right to modify any information and/or data in this user documentation without notice.

This documentation nor any of

its parts may be reproduced in any form or by any means without the prior written consent of Vector. To the maximum e

xtent permitted

under law, all technical data, texts, graphics, images and their design are protected by copyright law, various international

treaties and

other applicable law. Any unauthorized use may violate copyright and other applicable laws or regulat

ions.

7, Vector Informatik GmbH. Printed in Germany.

80874

User Manual GL3000/GL4000 Series Table of Contents

Table of Contents

1 Introduction 3

1.1 About this User Manual 4

1.1.1 Certification 5

1.1.2 Warranty 5

1.1.3 Support 5

1.1.4 Trademarks 5

2 GL3000/GL4000 Series – Overview 7

2.1 General Information 8

2.2 Connectors 9

2.2.1 Overview 9

2.2.2 Main Plug 10

2.2.3 Analog Plug 12

2.2.4 Digital Plug 13

2.2.5 Ethernet Connections 14

2.2.6 USB Connections 14

2.2.7 AUX Connections 15

2.2.8 Event Connection 16

2.2.9 WiFi Connection 16

2.3 Bus Systems 17

2.3.1 CAN 17

2.3.2 CAN Piggybacks 17

2.3.3 LIN 19

2.3.4 FlexRay 20

2.3.5 MOST150 20

2.4 Functions 21

2.4.1 Manual Switch On and Off the Logger 21

2.4.2 Automatic Switch On and Off the Logger (Sleep / Wake-up / Standby) 22

2.4.3 Memory Media 22

2.4.4 Digital Input 24

2.4.5 Digital Output 24

2.4.6 Analog Inputs 25

2.4.7 LEDs, Display, Keys 26

2.4.8 Beep 28

2.4.9 UPS 28

2.4.10 Serial Interfaces 28

2.4.11 Real-Time Clock with Battery 29

2.4.12 USB 30

2.4.13 Ethernet 31

2.4.14 Wireless LAN 31

2.4.15 3G 32

2.4.16 CCP/XCP 32

2.4.17 Diagnostics 33

2.4.18 Camera HostCAM 33

2.5 Technical Data 34

2.6 Included with Delivery 35

2.7 Accessories 35

3 Installation Configuration Programs 37

3.1 Overview 38

User Manual GL3000/GL4000 Series Table of Contents

3.2 Installation Vector Logger Configurator 38

3.2.1 Requirements 38

3.2.2 Setup 38

3.2.3 Overview 39

3.2.4 Quick Start 40

3.3 Installation G.i.N. Configuration Program 42

3.3.1 Requirements 42

3.3.2 Setup 42

3.3.3 Overview 42

3.3.4 Quick Start 44

4 Index 47

User Manual GL3000/GL4000 Series Introduction

1 Introduction

In this chapter you find the following information:

1.1 About this User Manual page 4

Certification

Warranty

Support

Trademarks

User Manual GL3000/GL4000 Series Introduction

1.1 About this User Manual

To find information

quickly

The user manual provides you the following access helps:

> At the beginning of each chapter you will find a summary of the contents,

> In the header you can see the current chapter and section,

> In the footer you can see to which version the user manual replies,

> At the end of the user manual you will find an index.

Conventions

In the two following charts you will find the conventions used in the user manual

regarding utilized spellings and symbols.

Style Utilization

bold

Blocks, surface elements, window- and dialog names of the

software. Accentuation of warnings and advices.

[OK] Push buttons in brackets

File

|

Save

Notation for menus and menu entries

Windows Legally protected proper names and side notes.

Source code

File name and source code.

Hyperlink Hyperlinks and references.

<STRG>+<S> Notation for shortcuts.

Symbol Utilization

Here you can find additional information and hints that eases the

work with the loggers.

This symbol calls your attention to warnings.

Here you can find additional information.

Here is an example that has been prepared for you.

Step-by-step instructions provide assistance at these points.

Instructions on editing files are found at these points.

This symbol warns you not to edit the specified file.

User Manual GL3000/GL4000 Series Introduction

1.1.1 Certification

Certified Quality

Management System

Vector Informatik GmbH has ISO 9001:2008 certification.

The ISO standard is a globally recognized standard.

1.1.2 Warranty

Restriction of

warranty

We reserve the right to modify the contents of the documentation or the software

without notice. Vector disclaims all liabilities for the completeness or correctness of

the contents and for damages which may result from the use of this documentation.

1.1.3 Support

You need support? You can get through to our hotline at the phone number

+49 711 80670-200

or you write an email to support@vector.com.

1.1.4 Trademarks

Protected

trademarks

All brand names in this documentation are either registered or non registered

trademarks of their respective owners.

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2 GL3000/GL4000 Series – Overview

In this chapter you find the following information:

2.1 General Information page 8

2.2 Connectors page 9

Overview

Main Plug

Analog Plug

Digital Plug

Ethernet Connections

USB Connections

AUX Connections

Event Connection

WiFi Connection

2.3 Bus Systems page 17

CAN

CAN Piggybacks

LIN

FlexRay

MOST150

2.4 Functions page 21

Manual Switch On and Off the Logger

Automatic Switch On and Off the Logger (Sleep / Wake-up / Standby)

Memory Media

Digital Input

Digital Output

Analog Inputs

LEDs, Display, Keys

Beep

UPS

Serial Interfaces

Real-Time Clock with Battery

USB

Ethernet

Wireless LAN

3G

CCP/XCP

Diagnostics

Camera HostCAM

2.5 Technical Data page 34

2.6 Included with Delivery page 35

2.7 Accessories page 35

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.1 General Information

GL3000 The GL3000 is a data logger with USB and Ethernet interface which processes CAN

messages with either 11-bit or 29-bit identifiers, Remote Frames, LIN messages and

analog measurement values. The data is stored on a Compact Flash card. The

configuration of the logger is done with the Vector Logger Configurator or the G.i.N.

Configuration Program. The installation is described in chapter 3.

GL3100 The GL3100 includes all the functionality of the GL3000. In addition its housing

features four buttons for input and a display for output.

GL3200 The GL3200 only differs from the GL3100 in that the data is recorded on a solid-state

disk instead of a Compact Flash card. This allows the data to be read out faster.

GL4000 The GL4000 includes all the functionality of the GL3000 and also supports FlexRay

recording. In addition its housing features four buttons for input and a display for

output.

GL4200 The GL4200 only differs from the GL4000 in that the data is recorded on a solid-state

disk instead of a Compact Flash card. This allows the data to be read out faster.

Basic functions

The following table shows the differences of the basic version of the logger variants.

Functions GL3000 GL3100 GL3200 GL4000 GL4200

CAN (9x)

•

LIN (2x)

•

FlexRay (2x)

•

Display

•

• •

Keys (4x)

•

Digital

input/output

(each 8)

•

Analog inputs

(6x)

•

USB Host

•

Ethernet

•

Memory media CF/USB

memory

CF/USB

memory

SSD CF/USB

memory

SSD

Options All loggers can be extended with the following options:

> Wireless LAN

> UMTS

> Analog expansion card with 8 analog inputs

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.2 Connectors

2.2.1 Overview

General information The loggers have the following connectors:

Front:

> 1 card drive for Compact Flash cards (for GL3000, GL3100 and GL4000 only)

> 1 slot for removable SSD (for GL3200 and GL4200 only)

> 1 USB host connector (reserved)

> 1 USB device connector

> 1 Ethernet connector

Back:

> 1 main connector: DSUB50 plug (male), e.g. for voltage supply, CAN, LIN,

FlexRay, internal analog inputs, RS232, KL15/Ignition

> 1 analog connector: DSUB25 plug (male), e.g. for analog inputs of the expansion

card, RS232

> 1 digital connector: DSUB25 plug (female) for digital inputs and outputs

> 2 Ethernet connectors

> 1 USB host connector for the connection of an USB memory medium

> 2 AUX sockets (Binder 5-pol, female) for LOGview (LCD Display) and VoCAN

(speech input/output)

> 1 event plug (Binder 5-pol, male) for switch box E2T2L

> 1 port for WiFi antenna (with WiFi option only)

Plug set The scope of delivery includes a plug set (2 x 25-pin, 1 x 50-pin) of the Automotive

sector for the DSUB connections with contacts and hoods. For a secure holding the

hoods can be screwed or clipped.

For the reliable assembly of the contacts a crimp tool is needed, e.g. a crimp tool can

be purchased from the CONEC company (www.conec.com):

> Material: Crimp tool for D-SUB standard stamped and formed contacts

> Order number: 360 X 10079 X

Alternatively DSUB plugs with solder contacts can be used (not contained in scope of

delivery).

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.2.2 Main Plug

DSUB50

pin assignment

The pins of the main plug (DSUB50, male) have the following meaning:

Pin Assignment Pin Assignment

1 FlexRay1+ 26 CAN3 Vbatt

2 FlexRay1- 27 CAN3 GND

3 GNDSense 28 CAN4 GND

4 GND 29 CAN4 Vbatt

5 GND 30 LIN1 Vbatt

6 CAN1 High 31 LIN2 Vbatt

7 CAN1 Low 32 UART3 Tx

8 CAN2 High 33 UART3 Rx

9 CAN2 Low 34 FlexRay2+

10 CAN3 High 35 FlexRay2-

11 CAN3 Low 36 BattSense

12 CAN4 High 37 Battery (VCC)

13 CAN4 Low 38 Battery (VCC)

14 LIN 1 39 CAN5 High

15 LIN 2 40 CAN5 Low

16 KL15/Wake 41 CAN6 High

17 K-Line 42 CAN6 Low

18 AnaIn1 43 CAN7 High

19 AnaIn2 44 CAN7 Low

20 AnaIn3 45 CAN8 High

21 AnaIn4 46 CAN8 Low

22 CAN1 Vbatt 47 CAN9 High

23 CAN1 GND 48 CAN9 Low

24 CAN2 GND 49 UART2 Tx

25 CAN2 Vbatt 50 UART2 Rx

Battery

(Term. 30)

The two pins are connected to one another internally. They are

used to supply the logger with power. In case of increased current

consumption and/or a small cable diameter, we recommend

connecting both pins.

GND

The two GND pins on the main plug and the GND pin on the

analog plug are connected to one another internally. In case of

increased current consumption and/or a small cable diameter, it is

recommended connecting both pins.

CAN

For CAN (see chapter 2.3.1), the CANx High and CANx Low pins

are connected. For the galvanically decoupled piggybacks, the

CANx GND and CANx Vbatt pins must also be connected.

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

LIN

The LIN channels are supplied with maximum 12 V from the supply

voltage of the data logger. If the reference voltage for a LIN

channel is higher than 12 V, this voltage (e.g. 24 V) must be

applied to the LIN1_Vbatt or LIN2_Vbatt

pins. In all other cases,

the LIN1/2_Vbatt pins are not connected.

It is recommended to connect also GND as ground supply beside

the LIN pins.

FlexRay

For FlexRay (see chapter 2.3.4), the FlexRay1+/FlexRay1- and

FlexRay2+/FlexRay2- pins are connected.

Analog inputs

For analog inputs 1 - 4, the AnaInx pins are connected.

Analog inputs 5 and 6 are hard-wired internally and connected to

BattSense and KL15/Wake respectively. They are therefore not

accessible through a plug.

UART

For the serial interfaces (see chapter 2.4.10), the UARTx Tx and

UARTx Rx pins are connected. The UART2 Tx/Rx pins are

connected internally with the UART2 Tx/Rx pins of the analog plug.

KL15/Wake

The logger is woken up by a positive edge on this pin.

KL15/Ignition, for example, can be connected for this purpose.

BattSense,

GNDSense

If the cables to the logger are long, the voltage drops off on the

Term. 30 line and the GND line due to the operating current. As a

result, a minimally lower voltage than the actual wiring system

voltage is measured with AnaIn5. To prevent this, the BattSense

and GNDSense pins can be connected close to the wiring system

voltage. AnaIn5 then measures the voltage at these pins.

Caution: It is recommended to connect the logger to the same voltage supply (e.g.

battery of the vehicle) as the vehicle or test equipment, respectively.

If two different voltage supplies are used for the logger and the test equipment, the

ground (GND) pins of the two voltage supplies must be connected.

Reverse-polarity

protection

For the voltage supply via Battery (Pins 37/38) and GND (Pins 4/5) a complete

reverse-polarity protection is available that in parallel also suppresses negative peaks

from the main power supply. A protection against positive peaks is also available.

Dependent on the temperature peaks from 35.88 V up to 42.12 V can be absorbed.

Then temporarily up to 1200 A can be discharged.

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.2.3 Analog Plug

DSUB25

pin assignment

The pins of the analog plug (DSUB25, male) have the following meaning:

Pin Assignment Pin Assignment

1 AnaIn7+ 14 AnaIn7-

2 AnaIn8+ 15 AnaIn8-

3 AnaIn9+ 16 AnaIn9-

4 AnaIn10+ 17 AnaIn10-

5 AnaIn11+ 18 AnaIn11-

6 AnaIn12+ 19 AnaIn12-

7 AnaIn13+ 20 AnaIn13-

8 AnaIn14+ 21 AnaIn14-

9 Reserved 22 Reserved

10 5V (out) 23 UART2 Rx

11 UART2 Tx 24 Vbatt (out)

12 RS232LinuxRx 25 RS232LinuxTx

13 GND

Analog

expansion

The analog inputs (differential) of expansion card A8I (see

chapter 2.4.6) are connected using this plug.

GND

This pin can be used as ground for 5V (out) and Vbatt (out). The

GND pin on the analog plug and the two GND pins on the main

plug are connected to one another internally.

5V (out)

Externally connected devices can be supplied with 5 V through

this pin. The voltage supply at this pin is switched off with a

switch if the logger is in sleep mode or standby mode. This

output can supply currents up to 1A.

Vbatt (out)

This pin outputs the voltage active at pin Battery (VCC) and is

protected with 2A.

UART

For the serial interface (see chapter 2.4.10), the UART2 Tx and

UART2 Rx pins are connected. These pins are connected

internally with the UART2 Tx/Rx pins of the main plug.

RS232LinuxRx,

RS232LinuxTx

These pins support an access to the logger to set the real time

clock (see chapter 3.2.4).

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.2.4 Digital Plug

DSUB25

pin assignment

The pins of this digital plug (DSUB25, female) have the following meaning:

Pin Assignment Pin Assignment

1 Reserved 14 DigIn1

2 DigOut1 15 DigIn2

3 DigOut2 16 DigIn3

4 DigOut3 17 DigIn4

5 DigOut4 18 DigIn5

6 DigOut5 19 DigIn6

7 DigOut6 20 DigIn7

8 DigOut7 21 DigIn8

9 DigOut8 22 Vbatt (out,switched)

10 Reserved 23 DigGND

11 Reserved 24 DigGND

12 Reserved 25 Sync (reserved)

13 Reserved

Digital inputs

The digital inputs (see chapter 2.4.4) are connected via the DigInx

pins.

Digital

outputs

The digital outputs (see chapter 2.4.5) are connected via the

DigOutx and DigGND pins.

DigGND

The two DigGND pins are the common ground of the digital

outputs and connected to one another internally. They are used to

divert possible high currents that could flow in on digital output

DigOutx. They are bridged internally with GND via a fuse.

It is recommended connecting a good ground if digital outputs are

used with high currents.

For currents higher than 1 A, the ground DigGND (preferably both

pins 23 and 24) must be connected to the vehicle ground (GND at

main plug).

Vbatt (out,

switched)

This pin outputs the voltage of Battery via a 1 A electrical fuse if

the logger is switched on.

This output is used for the operation of small accessory devices

which have no own sleep mode and are supposed to operate when

the logger is awake.

The ground of such device must be connected to the vehicle

ground (GND at main plug).

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.2.5 Ethernet Connections

Ethernet connector One 10/100 Mbit Ethernet connection is located on the front, and two 10/100 Mbit

Ethernet connections on the back with the following meanings:

Front

> Eth 1: Configuration of the logger and reading out of the logging files

Back

> Eth 2: Configuration of the logger and reading out of the logging files (analog to

Eth1), connector for one camera (CAMlog2 or network camera HostCAM) and for

the usage as interface in CANoe/CANalyzer.

> Eth 3: Connector for GLA150 (accessory for MOST150).

Logger as bus

interface

The loggers support a monitoring interface that allows the use of loggers as bus

interface for monitoring in CANoe/CANalyzer (since version 7.6 SP3).

The logger is connected via Ethernet to the CANoe/CANalyzer PC and sends after

measurement start the bus data to CANoe/CANalyzer, where the data can be

analyzed in the measurement setup. Sending messages with CANoe/CANalyzer is

not possible. The relevant CANoe/CANalyzer licenses must be provided by a

connected hardware interface on the PC or by a license dongle.

You can find further information in the Vector Logger Configurator manual, chapter

Monitoring Interface. There the configuration of the logger and CANoe/CANalyzer is

described in Tutorial: Usage as interface.

2.2.6 USB Connections

USB connection Two USB connections are located on the front, and one USB connection on the back

with the following meanings:

Front

> USB 1: Reserved.

> USB device connection with USB B socket for connection on the PC.

Back

> USB 2: USB host connection with USB A socket for connection of a USB memory

medium.

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.2.7 AUX Connections

AUX connection

The two additional 5-pin plug connections (connector series 711) AUX are intended

for the connection of the following logger accessories:

> LOGview (external display)

> Switch Box CAS1T3L (with one button, three LEDs and one sound)

> Switch Box CASM2T3L (with two buttons, three LEDs, one sound, and

microphone for voice recording)

> VoCAN (for voice recording and output)

The plug pin assignment is as follows (view of the contacts of the logger socket):

Pin Assignment

1 +5V

2 Ground

3 CAN high

4 CAN low

5 Vbatt

The AUX connections are wired to CAN9 internally. For this reason, this channel is

always equipped with a high-speed transceiver without wake-up capability and can no

longer be used freely if an AUX connection is used. If the AUX connections are not

used, CAN9 is fully available.

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.2.8 Event Connection

Event connection This plug is used for the connection of the Switch Box E2T2L with two buttons and

two LEDs, which is included in the scope of delivery. The buttons and the LEDs are

freely programmable.

The plug pin assignment is as follows (view of the contacts of the logger plug):

Pin Assignment

1 GND

2 3.3V

3 A

4 B

5 T

Switch Box wiring

2.2.9 WiFi Connection

WiFi antenna

connection

Each logger delivered with the WiFi option has a connection for the WiFi antenna on

the back. In the case of a logger without the WiFi option, a plastic plug is located

there instead.

The operating frequency of the antenna is approximately 2.4 GHz.

Caution: To satisfy FCC RF exposure requirements for mobile transmitting devices, a

separation distance of 20 cm or more should be maintained between the antenna of

this device and persons during operation. To ensure compliance, operations at closer

distances than this are not recommended.

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

2.3 Bus Systems

2.3.1 CAN

CAN channels

The loggers support 9 CAN channels.

Channel 1 - 4

Freely configurable via piggyback PCBs

Channel 5 - 8

Permanently occupied by high-speed CAN transceiver with

wake-up capability

Channel 9

Permanently occupied by high-speed CAN transceiver without

wake-up capability

Wake-up capability

The logger can be woken up on CAN channels 1 - 8. The wake-up capability can be

set via the configuration.

2.3.2 CAN Piggybacks

Piggybacks A piggyback is a plug-in PC-board which implements the interconnection of the logger

to a specific CAN bus by the use of various transceivers. The piggybacks are also

used in other loggers.

Available piggybacks for the GL3000/GL4000 series:

CAN Piggyback Transceiver Description Wake-up

Galvanically

decoupled

Piggyback 1043

1

TJA1043 CAN high-speed Yes No

Piggyback 1043mag

1

TJA1043 CAN high-speed Yes Yes

Piggyback 1042

2

TJA1042 CAN high-speed No No

Piggyback 1050 TJA1050 CAN high-speed No No

Piggyback 1055

3

TJA1055 CAN low-speed Yes No

Piggyback 1055mag

3

TJA1055 CAN low-speed Yes Yes

Piggyback Single

Wire

TLE6255G CAN Single Wire Yes No

Piggyback Truck

Trailer

WABCO CAN

Truck&Trailer

Yes No

1

Piggyback 1043/1043mag as successor of Piggyback 1041/1041mag

2

Piggyback 1042 as successor of Piggyback 251

3

Piggyback 1055/1055mag as successor of Piggyback 1054/1054mag

Galvanically

decoupled

piggybacks

Piggybacks 1041mag, 1043mag, 1054mag and 1055mag are magnetically decoupled

and available for CAN channels 1 - 4 of the GL3000/GL4000 series. Due to the

decoupling, the power supply and ground for these piggybacks must be connected at

the main plug (see chapter 2.2.2 Main Plug). For proper galvanic isolation, the

piggybacks must be powered from a different source than the logger.

User Manual GL3000/GL4000 Series GL3000/GL4000 Series – Overview

Info: For the galvanically decoupled transceiver, power supply (CAN1/2/3/4_Vbatt)

and ground (CAN1/2/3/4_GND) must be connected separately.

Replacing

piggybacks

The piggybacks can be exchanged. The installed piggybacks are automatically

detected (“plug & play”).

Info:

> First read the installation instruction completely.

> The case has to be opened to exchange the piggybacks.

> This must be done very cautiously and carefully, in order to not damage the

sensitive lines in the unit.

GL3000/GL4000

series

Now proceed as follows:

1. Screw off the back cover (with the main plug) of the logger. First remove the black

decorative caps and then unscrew the crosshead screws.

2. Carefully remove the back cover with the board from the housing until the

piggybacks are accessible. It is sufficient to pull out the board halfway.

Note that the USB cable of the GL3200 and GL4200 may under no circumstances

be folded or pulled!

3. Looking from the main plug, the four slots are located at the edge of the board in

the order of CAN1 - CAN4. The locations are marked red in Figure 1.

4. Remove the piggyback carefully from the mounting location.

5. Insert the new piggyback. As the piggybacks are structured asymmetrically, it is

not possible to use them in a turned position. If some slots are not occupied, you

must ensure that each piggyback is inserted exactly in its intended slot on the (4 x

4 =) 16-pin measuring connection strip. Galvanically isolated piggybacks contain

four further pins.

6. Reassemble the unit in the reverse order. Place the main board back in the

housing and ensure that the board has been inserted into the correct guide rail

(piggybacks: groove 6, main board: groove 1).

Note the ribbon cable of the membrane keypad here (not in the case of GL3000)

and the flat ribbon cable. Under no circumstances may they be folded or crushed!

7. It should be possible to slide the main board in the housing up to a few

millimeters from the end without forcing it in. Close the housing by applying light

pressure, and then secure it with the appropriate screw fasteners. The screws

should be secure but not excessively tight.

8. Please also attach the black decorative caps.

Caution: When performing this operation be sure not to touch the top or bottom of

the boards (logger main board or piggybacks).

Page is loading ...

Vector GL3000 series User manual

This manual is also suitable for

Vector GL3000 series User manual

Related papers

Other documents