Astonica 50105436 User manual

  • Hello! I am an AI chatbot trained to assist you with the Astonica 50105436 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT
1-888-424-3354
070905rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT
1-888-424-3354
OR
IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL
1-888-851-5569
PLEASE HAVE YOUR STORE NUMBER READY
Limited Warranty
World Factory, Inc.
®
Products for Home Use
World Factory, Inc.
®
(Seller) warrants to the original Buyer only, that each Astonica
®
Product will be
free from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE
SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY
FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc.
®
authorized service
center. Call 1-888-424-3354 for the location of the nearest authorized service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR
LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
®
Made in China
©2005 World Factory, Inc.
Distributed by:
World Factory, Inc.
Coppell, TX 75019
Model No: 50105436
48" Round Table
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
PARTS LIST
PART # DESCRIPTION QUANTITY
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-424-3354
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
ASSEMBLY INSTRUCTIONS
A Table Top 1
B Table Leg 4
C Leg Connector Ring 1
D Bumper 4
E Bolt 8
F Plastic Umbrella Cap 1
1.(SEE FIGURE 1) Insert bumper (D) into
previously drilled holes at top of each leg (B).
CAUTION: Do not place table top on a hard
surface during assembly. Possible damage
to table top can occur.
2.(SEE FIGURE 2) Place table top (A) upside
down on a flat non-scratch surface.
3. With bumper (D) installed, slide each leg (B)
into end cap leg fittings as show in diagram.
NOTE: Make sure bumper (D) on the leg stays
in place between leg and glass top.
4.Place leg connector ring (C) between legs and
loosely attach ring using bolts (E).
5.Check alignment of all legs, and correct,
if necessary before tightening bolts.
6.Gradually tighten all bolts, moving from one
leg, then the next until all legs firmly attached.
7.Place table right side up and install plastic
umbrella cap inside center hole of table.
NOTE: This product is intended for residential, non-commercial use.
A
B C
D
E
Figure 1
F
G
D
B
B
A
E
C
1
2
Figure 2
F
/