ALLEGION LEGGE G2 Series Installation guide

ALLEGION
Brand
ALLEGION
Model
LEGGE G2 Series
Type
Installation guide
Unclench by
screwdriver
INSIDE
SPRING CAGE
INSIDE
ROSE
TURN
AND
PULL
INSIDE
INSIDE
OUTSIDE
OUTSIDE
LEFT HAND
RIGHT HAND
LEFT
REVERSE
BEVEL
RIGHT
REVERSE
BEVEL
IN THE BOX DOOR HANDS DETERMINED FROM OUTSIDE
INSIDE
LEVER
OUTSIDE
LEVER
KEY
PUSH PIN
LOCK BODY
CYLINDER
ASSEMBLY
INSIDE
ROSE
SLEEVE
For 25mm(1")
Hole
LATCH
STRIKE
STRIKE BOX
OUTSIDE
TRIM
INSIDE
SPRING CAGE
POST
COMBINATION
SCREW
MOUNTING
SCREW
New Door Preparation
1A: Insert push pin into hole
in inside lever to depress catch.
1B: Remove the inside
lever from spindle.
1C: Remove inside rose
by turning and pulling off.
1D: Unscrew two mounting
screws in lock body by screwdriver.
Fold template on edge of
door mark site 70mm(2-3/4")
of holes.
Drill a hole
through door (from both sides
to avoid damaging door).
54mm(2-1/8")
Cut out a 58x29x4mm
(2-9/32"x1-1/8"x5/32") base.
CENTER LINE
BASE
54
58
29
25
70
4
DISASSEMBLE INSIDE LEVER AND ROSE
PUSH PIN
HOLE
INSIDE
LEVER
INSIDE
LEVER
CATCH
MOUNTING
SCREW
LOCK BODY
"
"
"
Fit Doors 35mm(1-3/8 ) to 50mm(2 ) Thick Backset 70 mm (2-3/4 )
G2 Series Installation Instructions
A:
B:
C:
D:
Drill a 25mm (1 ) hole in
door edge.
"
DOOR HANDING
ADAPTOR
NOTE: For doors thinner
than 35 mm (1-3/8")
fit adaptors supplied
under inside spring
cage and/or outside trim.
LE70644A
3E:
Disassemble inside
lever by push pin.
INSIDE
ROSE
3F:
Fix inside rose and make sure inside
rose and inside spring cage are tightened.
3G:Slide lever onto spindle.
Push lever completely into place.
(Pull on lever to make sure that
catch is fully engaged).
INSTALL STRIKE
STRIKE BOX
STRIKE
DOOR
JAMB
CENTER LINE
After door is
closed, guardbolt
is retraced
INSIDE
SPRING
CAGE
INSIDE
LEVER
PUSH PIN
CATCH
①
②
IMPORTANT
CATCH
If the door is thicker
than 50mm,the catch
will be covered by
inside rose, do not
install inside lever
and lock.
Align dimples on
rose with rectangular
hole in spring cage.
Push in rose until
dimples snap into
rectangular hole.
ADJUST OUTSIDE TRIM TO SUIT DOOR THICKNESS
OUTSIDE
LEVER
KEY
2A: Turn key 75°clockwise, insert
push pin into hole in outside lever to
depress catch. Remove the outside lever .
PUSH PIN
HOLE
POST
LOCK BODY
2B: Unscrew two
posts in lock body
by screwdriver.
CENTER LINE
OUTSIDE
TRIM
2C: Adjust outside trim according
to the door thickness, make sure the
lock body at both sides is symmetrical.
2D:
Screw two posts
back so as to hold the
outside rose tightly.
2E:
Turn key 90°clockwise and
push the lever into the maximum
extent; rewind key.
KEY
OUTSIDE
LEVER
①
②
③
①
②
③
Catch can not
be covered
by rose.
Turn back
key to normal
position.
Correct
keyway
direction
after
assembling.
JOINT
BLADE
Oppose joint
blade to catch.
"
[ 45mm(1-3/4 )
"
(1-3/4 ) ]
This lock is factory preset for doors, if your door thickness
is 45mm , skip Step and go to Step directly.
INSTALL LEVERSET TO DOOR
3A: Insert latch unit and
fix it with two wood screws.
LATCH
LOCK BODY
LATCH
3B:Place lock body into position. Make sure
that latch prongs engage chassis in housing,
and slide engages latch tail.
MOUNTING
SCREW
LOCK
BODY
INSIDE
SPRING
CAGE
3C:Install inside spring cage ,
Screws should be tightened to
its full length.
3D:Fix the inside lever and check if the
rotation is smooth. Adjust the radial clearance
between inside spring cage and inside lever.
INSIDE
LEVER
PRONGS
LATCH
Align the joint
blade with slot.
LATCH
TAIL
SLIDE
Allegion Australia
www.allegion.com.au
Allegion New Zealand
www.allegion.co.nz
  • Page 1 1
  • Page 2 2

ALLEGION LEGGE G2 Series Installation guide

ALLEGION
Brand
ALLEGION
Model
LEGGE G2 Series
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents