ALLEGION Olivari PT Series Installation Instructions Manual

Brand: ALLEGION

Model: Olivari PT Series

Type: Installation Instructions Manual

*47280191*

47280191

3 Install spring cages.

Arrow matches

down rotation of lever

(reverse angle)

4 Install mounting posts and screws.

Install mounting posts on exterior side of door; install mounting screws on interior

side of door.

Flush with

channel

5 Insert spindle.

Install so spindle length is same on both sides of door.

Thin slotted

side UP

This side DOWN

6 Check operation.

Conrm smooth operation with no sticking.

If not operating smoothly, perform these steps:

a. Slightly loosen spring cage mounting screws.

b. Conrm function by cycling lever.

c. Temporarily slide lever onto spindle. Conrm lever is horizontal with no lever droop.

d. Retighten spring cage mounting screws.

7 Install surface mount screws.

Model PT10, Rose Installation Instructions

PT-Series Tubular Passage Trim

1 Insert latch into door edge.

Rotate if necessary

so flat side matches

door orientation

2 Install face plate and lightly tighten.

Parts

Required Supplied

Phillips

screwdriver

3mm

hex key

Tools

Parts

A Passage latch

B Latch face plate

C Latch screws (2)

D Left hand spring cage

E Right hand spring cage

F Mounting posts (2)

G Mounting screws (2)

H Solid spindle

I Surface mount screws (4)

J Roses (2)

K Nylon bushings (2)

L Left hand lever

M Right hand lever

N Set screws (2)

O 3mm hex key

*47280193*

47280193

3 Insert spindle.

Adjust if necessary so spindle length is same on both sides of door.

Thin slotted

side UP

This side DOWN

Adjust length

if necessary

C-clip must be

on interior side

4 Install spring cages.

Arrow matches

down rotation of lever

(reverse angle)

5 Install mounting posts and screws.

Install mounting posts on exterior side of door; install mounting screws on interior

side of door.

Flush with

channel

6 Check operation.

Conrm smooth operation with no sticking.

If not operating smoothly, perform these steps:

a. Slightly loosen spring cage mounting screws.

b. Conrm function by cycling lever.

c. Temporarily slide lever onto spindle. Conrm lever is horizontal with no lever droop.

d. Retighten spring cage mounting screws.

7 Install surface mount screws.

Model PT40, Rose Installation Instructions

PT-Series Tubular Privacy Trim

1 Insert latch into door edge.

Hole on side of latch must face interior side of door.

Rotate if necessary

so flat side matches

door orientation

Hole faces

interior side

2 Install face plate and lightly tighten.

Parts

Required Supplied

Phillips

screwdriver

3mm

hex key

Tools

Parts

A Privacy latch

B Latch face plate

C Latch screws (2)

D Split spindle

E Left hand spring cage

F Right hand spring cage

G Mounting posts (2)

H Mounting screws (2)

I Surface mount screws (2)

J Left hand rose

K Right hand rose

L Nylon bushings (2)

M Left hand lever

N Right hand lever

O Set screws (2)

P 3mm hex key

Q Privacy pin

Printed in U.S.A.

47280193 Rev. 02/20-a

10 Install privacy pin.

Privacy pin should easily push in and out to lock/unlock.

11 Fully tighten face plate.

8 Install roses.

Roses are handed. Hole must be on latch side to align with pin, and slot must be

at the bottom.

Slot at

bottom

Slot at

bottom

Nylon

bushing

Nylon

bushing

Snaps in

place

Hole towards

door edge

Hole

9 Install levers.

Set screw

backed out

Set screw

on underside

Tighten

set screws

Printed in U.S.A.

47280191 Rev. 02/20-a

10 Fully tighten face plate.8 Install roses.

Slot at

bottom

Slot at

bottom

Nylon

bushing

Snaps in

place

Nylon

bushing

9 Install levers.

Set screw

backed out

Set screw

on underside

Tighten

set screws

*47280192*

47280192

1 Install spring cage.

inserts into

door hole

(reverse angle)

inserts into

door hole

(reverse angle)

align mounting holes to

centerlines on door

2 Install surface mount screws.

3 Install rose.

Snaps in

place

Slot at

bottom

Nylon

bushing

4 Install lever.

Set screw

backed out

Set screw

on underside

Tighten

set screw

spring cages.

Model PT170 (single dummy), trim for one side of door, Rose

Model PT172 (double dummy) trim for both sides of door, Rose

Installation Instructions

PT-Series Dummy Trim

Single Dummy parts

Required Supplied

Phillips

screwdriver

3mm

hex key

Tools

Right hand

shown

Parts

A Spring cage

B Surface mount screws (4)

C Rose

D Nylon bushing

E Lever

F Set screw

G 3mm hex key

Single Dummy installation

Printed in U.S.A.

47280192 Rev. 02/20-a

3 Install split spindle

Adjust if necessary so spindle length is same on both sides of door.

Seam must

be at top

and bottom

of spindle

4 Install surface mount screws

5 Install roses.

Snaps in

place

Slot at

bottom

Nylon

bushing

Slot at

bottom

Nylon

bushing

6 Install levers.

Set screw

backed out

Set screw on underside

Tighten

set screws

Double Dummy installation (continued)

Double Dummy parts

Required Supplied

Phillips

screwdriver

3mm

hex key

Tools

Left

hand

Right

hand

1 Install spring cages 2 Install mounting posts and screws.

Flush with

channel

Parts

A Spring cages (2)

B Mounting posts (2)

C Mounting screws (2)

D Split spindle

E Surface mount screws (4)

F Roses (2)

G Nylon bushings (2)

H Levers (2)

I Set screws (2)

J 3mm hex key

Double Dummy installation

ALLEGION Olivari PT Series Installation Instructions Manual

ALLEGION Olivari PT Series Installation Instructions Manual

ALLEGION Olivari PT Series Installation Instructions Manual

Related papers

Other documents