Morris MHR-20044S is an oil-filled radiator with WiFi function, allowing you to control it remotely. It features multiple power modes, including Eco mode for energy-saving, as well as adjustable thermostat settings for customized comfort. The timer function enables automatic power on and off, while the child lock ensures safe operation. Its sturdy design with integrated wheels and rear handle provides easy maneuverability.
Morris MHR-20044S is an oil-filled radiator with WiFi function, allowing you to control it remotely. It features multiple power modes, including Eco mode for energy-saving, as well as adjustable thermostat settings for customized comfort. The timer function enables automatic power on and off, while the child lock ensures safe operation. Its sturdy design with integrated wheels and rear handle provides easy maneuverability.
Oil filled radiator
with WiFi function
User manual
Model: MHR-20044S
This product is only suitable for well insulated spaces or occasional use.
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
Safety Warnings
PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY
BEFORE USING THE APPLIANCE
1. This appliance can be used by children aged from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by children without
supervision.
2.Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3
years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed
in its intended normal operating position and they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less
than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
3.CAUTION - Some parts of this product can become very hot and cause burns. Particular attention has to be
given where children and vulnerable people are present.
4.If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
5. WARNING: In order to avoid overheating, do not cover the heater.
6.The heater must not be located immediately below a socket-outlet.
7.Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
8.Do not use the appliance for other than its intended use. For domestic indoor use only.
9.Place the appliance on a flat, stable, heat-resistant surface. Operating the product in any other position
could cause a hazard.
10.There may be trace of odour during the first few minutes of initial use. This is normal and will quickly
disappear.
11.Do not attempt to repair, disassemble or modify the appliance. There are no user-serviceable parts inside.
12.CAUTION – if using an extension lead please ensure you do not exceed the maximum rated running
wattage/load of the extension lead.
13.Disconnect from mains when not in use or when moving or cleaning.
14.The heater is hot when in use. To avoid burns, do not let bare skin touch hot surface.
15.Do not insert or allow foreign objects to enter the ventilation or exhaust openings as this may cause an
electric shock , fire or damage to the appliance.
16.Do not cover the heater. A fire may occur if the heater is covered with or touches flammable material,
including curtains, drapes, bedding etc. when in operation. KEEP THE HEATER AWAY FROM SUCH
MATERIALS.
17.
KEEP OUT OF REACH OF CHILDREN. Swallowing can lead to chemical burns,
perforation of soft tissue, and death. Severe burns can occur within 2 hours of
ingestion. Seek medical attention immediately.
18. Keep batteries out of the reach of children.
19. Do not allow children to replace batteries without adult supervision.
20. Do not short-circuit batteries.
21. Do not heat batteries.
22. Remove batteries from equipment if it is not to be used for an extended period of time unless it is for
emergency purposes.
23. Always select the correct size and type of battery most suitable for the intended use.
24. Information provided with the equipment to assist correct battery selection should be retained for
reference.
25. Clean the battery contacts and also those of the equipment prior to battery installation.
26. Ensure that the batteries are installed correctly with regard to polarity (+ and –).
27. Remove exhausted batteries promptly.
28. Do not dismantle batteries.
29. Do not dispose of batteries in fire except under conditions of approved and controlled incineration.
30. Batteries may be disposed of via communal refuse arrangements provided no local rules to the contrary
exist.
PICTURES IN THE MANUAL ARE FOR REFERENCE ONLY
AND IS SUBJECT TO THE PHYSICAL PRODUCT IN THE PACKING BOX
Assembly
Turn the radiator upside-down on a scratch-free and stable surface to prevent damage to the paint finish or
your floor surfacing.
-Turn the radiator upside-down
-Pull down the wheel bases to both out sides, see Fig 1.
Only operate the radiator after the wheel bases are pulled down as below picture.
Fig 1
Controls
A.Heater body
B.Control panel
C.Wheel base
D.Rear handle
E.Remote control storage
slot
F.On/off power switch
G.Cable storage
a. Stand-by button
b. Power/Mode button
c. Thermostat button
d. Timer button
e.－: Temperature & hours decrease
button
f. ＋ : Temperature & hours increase
button
Remote control
The remote control requires 2pcs triple A (Α+++) batteries. Follow the +/- polarity indicated on
the remote control.
The remote control must be pointed towards the remote sensor on the control panel.
If the remote control doesn’t operate as expected, replace the batteries.
Move the appliance using the integrated handle.
The remote control can be stored in the slot integrated into the appliance if not used.
On
Press the on/off power switch [F] to turn the appliance on. The stand-by button [a] ( ) and Timer button
[d]( ) will light on. The product is now in stand-by awaiting a mode to be selected via the buttons on the
appliance or the remote control. Press button ( ) or ( ), the screen and other buttons will light on also.
The appliance emits a beep sound.
The following settings can be performed using the touch panel or the remote control.
A beep sound is emitted at every key press.
Press the stand-by button [a] to exit the stand-by mode and begin selection of the different modes. Heater will
start working under Eco mode ( ).
Heating power and Eco mode setting
Press the Power/Mode button (b), it will cycle from Eco mode( ) High power ( ) Medium
power ( ) Low power( ) -”Baby mode”.
Under Low power, Medium power and High power setting, the heater will keep working controlled by thermal
cut-out.
Note:
The higher the power is, the quicker the desired temperature will be achieved but the power consumption will
be higher. Lower power levels are recommended when the heater is being used for an extended period of
time.
Eco mode
Press the Power/Mode button (b), until the “ECO” light turn on.
Under Eco mode, the heating power will adjust automatically when the room temperature is approaching the
setting temperature.
Example: The setting temperature is 25℃. When the room temperature is less than 22℃, the heater will work
under High power ( ). When the room temperature rises to 23℃, the heater will change to work under
Medium power ( ). When the room temperature rises to 24℃, the heater will change to work under Low
power( ). When the room temperature reaches to the setting temperature 25℃, the heater will switch off
automatically. And when the room temperature is lower than setting temperature, the heater will switch on
again under Eco mode.
Remark: if no thermostat setting, the default temperature is 23℃ under Eco mode.
Thermostat setting
Anti-frosting setting: 5°C
Desired temperature setting range:10 °C--30 °C
1. Press the Power/Mode button (b) to set the power mode.
2. Press the thermostat button (c), the temperature digit will blink.
3. Use the “+” and “-” [f] and [e] buttons to set the desired temperature.
4. The setting temperature digit will stop blinking and the setting temperature will appear on screen. The
heater will maintain the air temperature in the room by switching on and off automatically.
Remark: No matter under any power mode to set the temperature, after thermostat setting, the heater
will work under ECO mode only.
Note: The temperature shown on the screen is just the setting temperature.
Timer : Auto power on
Note:This function should only be set if you require the heater to be automatically turned on after a certain
period of time (1 to 24 hours from the time the function is set). Only make timer power on setting under Stand-
by mode.
1. Press the on/off power switch [F] to turn the appliance on. The button stand-by button [a] ( ) and Timer
button [d] ( ) will light on. The appliance will be in Stand-by mode.
2. Press the Timer button(d), the light on( ) and ( )will turn on, and the start hour digit (0.0) will blink.
3. Use the “+” and “-” buttons [f] and [e] to set the heater operation time between 1 and 24 hours. 0.0-5.0
hours increase by 0.5 hour, 5.0-24 hours increase by 1 hour. This function will activate once the hour digit
stops blinking. The count down digits will show on the display and the timer symbol ( ) will keep blinking till
time runs out.
4. The heater will automatically turn on when the time runs out.
Remark: After the timer power on setting, can make the power mode and temperature setting. So that the
heater will turn on at the desired temperature and power mode setting.
Note: When using timer modes, consideration should be given to the fact that the heater may come on whilst
unattended. Always follow the safety instructions provided.
Timer : Auto power off
Note:This function should only be set if you require the heater to be automatically shut off after a certain
period of time (1 to 24 hours from the time the function is set)
1. When heater working, press the Timer button(d), the light on ( ) will turn on, and the start hour digit (0.0)
will blink.
4. Use the “+” and “-” buttons [f] and [e] to set the heater operation time between 1 and 24 hours. 0.0-5.0
hours increase by 0.5 hour, 5.0-24 hours increase by 1 hour. This function will activate once the hour digit
stops blinking. The countdown digits will show on the display.
3. The heater will automatically shut off when the time runs out.
Child lock setting
Press both stand-by button [a] and Power/Mode button (b) for 3 seconds, the buttons will be locked, and the
symbol ( ) will show on display. If need unlock it, press both buttons for 3 seconds again.
If want to turn off the buttons’ beep sound, press both “+” and “-” buttons [f] and [e] for 3 seconds. If want to
recover the beep sound, press both buttons for 3 seconds again.
Off
Press the stand-by button [a] until sleep mode is selected and the control panel screen goes off.
Press the on/off switch [F] to turn the appliance off completely.
To disconnect the appliance, remove the plug from the socket.
Tip-over protection
This heater is protected with a safety switch that turns off the appliance automatically when the heater falls
over or is at an excessive angle from the horizontal. This helps prevent accidents, and the heater will resume
operation when it is put back upright.
Overheat protection
This heater is protected with overheat protection that switches off the appliance automatically in case of
severe overheating. In this case, unplug the appliance, wait about 30 minutes for it to cool and remove any
possible cause of overheating, eg. something covering the heater. Check for damage to the appliance, the
cord and the plug. If there is no damage, plug the unit back in and switch it on as described above. If the
heater still does not turn on, please contact Customer Service for assistance.
Maintenance and cleaning
The appliance should be regularly cleaned when in use in accordance with the following instructions:
1. Unplug and let the appliance cool before cleaning.
2. Gently clean the outside surface and the control panel of the appliance with a damp lint-free soft cloth.
3. If dust is present within the slits of the device, it is recommended to blow them through the use of a vacuum
cleaner, a blower .
4. Do not use harsh detergents, chemical cleaners or solvents as they may damage the appliance feet.
Storage
1.Keep the original packaging to disassemble the appliance and store it.
2.Keep the appliance in a dry and clean place.
3.Store the unit out of reach of children.
Waste electrical products should not be disposed of with household waste.
Some chemicals contained within electrical/electronic products or batteries can be harmful to health
and the environment.Please recycle where facilities exist. Check with your local authority or local
store for recycling advice.
Item
Symbol
Value
Unit
Item
Unit
Heat
output Model: MHR-20044S
Type of heat input, for electric storage
local
space heaters only (select
one)
Nominal heat output
Pnom
2.5
kW
manual heat charge control, with
integrated thermostat
No
Minimum heat output
(indicative)
Pmin
1.0
kW
manual heat charge control with
room and/or outdoor temperature
feedback
No
Maximum continuous
heat output
Pmax,c
2.5
kW
electronic heat charge control with
room and/or outdoor temperature
feedback
No
Auxiliary
electricity
consumption
fan assisted heat output
No
At nominal heat output
elmax
N/A
kW
Type of heat output/room temperature
control
(select
one)
At minimum heat output
elmin
N/A
kW
single stage heat output and no
room temperature control
No
In standby mode
elSB
0.00144
kW
Two or more manual stages, no
room temperature control
No
with mechanic thermostat room
temperature control
No
with electronic room temperature
control
Yes
electronic room temperature
control plus day timer
No
electronic room temperature
control plus week timer
No
Other control options (multiple
selections
possible)
room temperature control, with
presence detection
No
room temperature control, with
open window detection
No
with distance control option
Yes
with adaptive start control
No
with working time limitation
Yes
with black bulb sensor
No
Contact details
Kalliopi Karyda & Co LP
87A,17is Noemvriou str, P.C.55535
Pylea, Thessaloniki, Greece
T:+302316006600 F:+302316006650
NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life,
should be disposed of separately from your household waste. Please dispose of
this equipment at your local community waste collection/ recycling centre.
In the European Union there are separate collection systems for used electrical
and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Kalliopi Karyda & Co LP states that this product, complies with the requirements of
below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14 / 35 / EU
ErP Directive: 09 / 125 / EC
RED Directive: 14 / 53 / EU
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU & 15 / 863 / EU
The detailed declaration of conformity can be found at www.morris.gr
Exclusive importer in Greece:
Kalliopi Karyda & Co LP
87A, 17is Noemvriou str, P.C. 55535
Thessaloniki – Greece
T: +302316006600 | F: +302316006650
www.morris.gr
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Morris MHR-20044S is an oil-filled radiator with WiFi function, allowing you to control it remotely. It features multiple power modes, including Eco mode for energy-saving, as well as adjustable thermostat settings for customized comfort. The timer function enables automatic power on and off, while the child lock ensures safe operation. Its sturdy design with integrated wheels and rear handle provides easy maneuverability.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Morris MHR-20025 Instructions Manual
-
-
-
-
-
-
-
-
-
Other documents
-
LLOYTRON STAY WARM User manual
-
United UHF-849 Operating instructions
-
-
De’Longhi Slim Style Ceramic HX65L22 User manual
-
RAMTONS RM/475 User manual
-
-
-
DeLonghi DCH7093ER Owner's manual
-
Chemin'Arte Oxford 119 Installation And User Instruction Manual
-
DeLonghi TCH8093ER User guide
