Tappan B6BW Installation guide

B6BW
Tappan
Brand
Tappan
Model
B6BW
Category
Rack accessories
Type
Installation guide

This manual is also suitable for

DRIP GUARD KIT FOR B6(B,E)W AIR HANDLERS
IMPORTANT SAFETY INFORMATION
Please read all instructions before using this equipment. Pay
attention to all safety warnings and any other special notes
highlighted in the manual. Safety markings are used frequently
throughout this manual to designate a degree or level of
seriousness and should not be ignored.
WARNING indicates a potentially hazardous situation that if
not avoided, could result in personal injury or death.
CAUTION indicates a potentially hazardous situation that if
not avoided, may result in minor or moderate injury or property
damage.
These instructions are primarily intended to assist qualified
individuals experienced in the proper installation of this kit. Some
local codes require licensed installation/service personnel to
install this type of equipment. Please read all instructions carefully
before starting the installation. Return these instructions to the
customer’s package for future reference.
WARNING:
RISK OF ELECTRICAL SHOCK
Failure to follow these warnings can cause serious
injury, fire, electrical shock, or death.
• Shutoffallelectricalpowertotheunitbefore
performinganymaintenanceorserviceonthe
system.Failuretocomplymayresultinpersonal
injury or death.
• Unlessnotedotherwiseintheseinstructions,
only factory authorized parts or accessory
kitsmay beusedwith thisproduct. Improper
installation,service,adjustment,ormaintenance
maycauseexplosion,re,electricalshockor
otherhazardousconditions whichmay result
inpersonalinjuryorpropertydamage.
INSTALLATION INSTRUCTIONS
7096980 (NEW)
ABOUT THE DRIP GUARD
This kit consists of a metal drip guard and filter relocation fixture
that is designed for use in B6BW & B6EW air handlers. The kit
is intended to prevent condensate from dripping out of the unit.
DRIP GUARD INSTALLATION
Read these installation instructions completely before proceeding.
Refer to the manufacturer’s instructions for more installation
information.
1. Disconnect all power to the unit.
2. Remove the front panel from the air handler.
3. Remove filter from rack inside of the case.
4. Install drip guard inside of the case so that the surface is slanted
towards the drain pan. Position the two cutouts (on the edge
of the guard) into the flanges of the drainpan.
5. Install the rolled edge of the bottom rail over the front edge
of the cabinet. Make sure the bottom edge of the cabinet is
straight and the bottom rail is seated firmly on the cabinets
edge. See Figure 1.
6. Install the side rails by placing the ends into channel of bottom
piece, so that the open area of the channel is facing towards
the middle of the air handler. NOTE: Make sure the seam
where the side rails and filter rack meet are flush with each
other. See Figure 2.
7. Secure side rails to the air handler, using self tapping screws.
8. Slide filter between both side rails until it stops in the bottom
rail.
9. Reconnect electrical power to the unit. Refer to the installation
manual for proper startup sequence.
POSITION BACK EDGE
OF DRIP GUARD INTO
THE DRAIN PAN
DRAIN
PAN
DRIP
GUARD
FILTER RACK
(BOTTOM RAIL)
PLACE ROLLED EDGE
(BACK SIDE OF BOTTOM RAIL)
ON FRONT EDGE OF CABINET
Figure 1. DripGuardFolded
DRIP GUARD
FILTER RACK
(BOTTOM RAIL)
FILTER RACK
(LEFT SIDE RAIL)
FILTER RACK
(RIGHT SIDE RAIL)
SELF TAPPING
SCREWS
(x2 PER RAIL)
Figure 2. DripGuardInstalled
Specifications & illustrations subject to change without notice or incurring obligations (05/15).
O’Fallon, MO, © Nortek Global HVAC LLC 2015. All Rights Reserved.
  • Page 1 1

Tappan B6BW Installation guide

B6BW
Tappan
Brand
Tappan
Model
B6BW
Category
Rack accessories
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents