Metra Electronics 99-8714 User manual

Brand
Metra Electronics
Model
99-8714
Category
Motorcycle Accessories
Type
User manual

Metra Electronics 99-8714 allows you to install a DIN radio or stacked DIN units into your 2008 Smart Fortwo. The kit includes a radio housing, pocket, and all necessary hardware for a quick and easy installation.

Here are some of the features of the Metra Electronics 99-8714:

  • DIN Radio Provision with Pocket: This allows you to install a single DIN radio into your vehicle. The pocket can be installed in either the top or bottom of the radio housing.
  • Stacked DIN Units Provision: This allows you to install two DIN units into your vehicle, one above the other.
  • Easy Installation: The 99-8714 is designed for a quick and easy installation. The included instructions will guide you through the process step-by-step.

Metra Electronics 99-8714 allows you to install a DIN radio or stacked DIN units into your 2008 Smart Fortwo. The kit includes a radio housing, pocket, and all necessary hardware for a quick and easy installation.

Here are some of the features of the Metra Electronics 99-8714:

  • DIN Radio Provision with Pocket: This allows you to install a single DIN radio into your vehicle. The pocket can be installed in either the top or bottom of the radio housing.
  • Stacked DIN Units Provision: This allows you to install two DIN units into your vehicle, one above the other.
  • Easy Installation: The 99-8714 is designed for a quick and easy installation. The included instructions will guide you through the process step-by-step.
INSTALLATION INSTRUCTIONS FOR PART 99-8714
APPLICATIONS
SMART FORTWO
2008
KIT FEATURES
• DIN Radio Provision with Pocket
• Stacked DIN Units Provision
A) Radio Housing • B) Pocket
KIT COMPONENTS
A
TOOLS REQUIRED:
• Small Flat Blade Screwdriver/ Panel Removal Tool
• T-20 Torx Screwdriver
1-800-221-0932
© COPYRIGHT 2008 METRA ELECTRONICS CORPORA
TION
www.metr
aonline.com
B
99-8714
Dash Disassembly
-
Smart Fortwo 2008...................................
1
Kit Assembly
- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- Stacked DIN Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Final
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TABLE OF CONTENTS
99-8714
*Note:
Refer also to the instructions included with the aftermarket radio.
99-8714 DASH DISASSEMBLY
SMART FORTWO 2008
A
B
C
D
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip the Hazard button switch panel.
(
Figure A)
2
Remove (1) T-20 Torx head screw.
(Figure B)
3
Carefully unclip the panel surrounding
the radio, start at the top of the dash
and work your way down.
(Figure C)
4
Remove (4) T-20 Torx head screws
from around the radio. (
Figure D)
5
Disconnect the wire harness and
antenna and remove radio.
6
Continue to kit assembly.
99-8714 KIT ASSEMBLY
2
Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
2
Snap the pocket into the radio hous-
ing.
(Figure C)
3
Continue to final assembly.
NO
TE:
Pocket may be installed in top
or bottom of radio housing.
A
B
C
Note: Refer also to the instructions included with the aftermarket radio.
DIN RADIO PROVISION WITH POCKET
99-8714 KIT ASSEMBLY
3
Slide the DIN cages into the radio
housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
Slide the aftermarket units into the
cage until it snaps into place.
(Figure B)
2
Continue to final assembly.
A
B
Note: Refer also to the instructions included with the aftermarket radio.
STACKED DIN UNITS PROVISION
99-8714 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4
99-8714
NOTES
5
99-8714 INSTRUCTIONS
1-800-221-0932
REV. 03/27/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST99-8714
www.metraonline.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra Electronics 99-8714 User manual

Brand
Metra Electronics
Model
99-8714
Category
Motorcycle Accessories
Type
User manual

Metra Electronics 99-8714 allows you to install a DIN radio or stacked DIN units into your 2008 Smart Fortwo. The kit includes a radio housing, pocket, and all necessary hardware for a quick and easy installation.

Here are some of the features of the Metra Electronics 99-8714:

  • DIN Radio Provision with Pocket: This allows you to install a single DIN radio into your vehicle. The pocket can be installed in either the top or bottom of the radio housing.
  • Stacked DIN Units Provision: This allows you to install two DIN units into your vehicle, one above the other.
  • Easy Installation: The 99-8714 is designed for a quick and easy installation. The included instructions will guide you through the process step-by-step.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents