Acculab 98648-013-61 Operating instructions

Page is loading ...

English page 2

In cases involving questions of

interpretation, the German-language

version shall prevail.

Deutsch Seite 17

Im Auslegungsfall ist die

deutsche Sprache maßgeblich.

Français page 32

En cas de questions concernant

l’interprétation, la version

en langue allemande fera autorité.

Italiano pagina 47

In caso di interpretazione,

fa testo la versione in lingua tedesca.

Español página 62

En caso de interpretación,

la versión en lengua alemana

será determinante.

2 Warnings and Safety

Precautions

3 Getting Started

5 Operation

5 Basic Weighing Function

5 Description of the Keys

Application Programs

6 Toggling between Weight Units

7 Counting

8 Weighing in Percent

9 “Hold” Display

10 Totalizing

11 Specific Gravity

12 Calibration/Span Adjustment

13 Configuration (Setup Menu)

14 Error Codes

Overview

15 Specifications

16 Accessories (Options)

16 C Marking

2

Contents Warnings and

Safety Precautions

Safety Information

§ To prevent damage to the equip-

ment, please read these operating

instructions carefully before using

your balance/scale.

! Do not use this equipment in

hazardous areas.

! Make sure the voltage rating printed

on the power supply is identical to

your local line voltage.

! Use only commercially available 9V

batteries. If desired, you can use a

rechargeable battery (not included).

– The balance is energized at all

times unless you disconnect the AC

adapter and, if connected, the

battery.

– Protect the AC adapter from contact

with liquid

! Exposure to excessive electromag-

netic interference can cause the

readout value to change. Once the

disturbance has ceased, the instru-

ment can be used again in accor-

dance with its intended purpose.

Installation

– It is recommended to connect

Acculab accessories and options,

as these are optimally designed for

use with your balance/scale.

– Do not open the balance/scale

housing as this may void the

manufacturer’s warranty.

3

Equipment Supplied

– Balance/scale with in-use cover

– Weighing pan

– Plug-in AC adapter

Additional equipment with models VIC-612, VIC-412,

VIC-212, VIC-711, VIC-511:

– Calibration weight

Additional equipment with models VIC-303, VIC-123,

VIC-4MG, VIC-2MG:

– Calibration weight

– Round glass draft shield

– Level indicator and adjustable feet

Storage

$ Do not stack more than 3 balances on top of one another

at a time.

Installation

Choose a location that is not subject to the following nega-

tive influences:

– Heat (heater or direct sunlight)

– Drafts from open windows and doors

– Extreme vibrations during weighing

– Excessive moisture

Setting Up the Balance/Scale

§ Place the components on the balance/scale in the

following order:

– Reversible round weighing pan

– Round glass draft shield on models VIC-303, VIC-123,

VIC-4MG, VIC-2MG

Getting Started

4

Connecting the

Balance/Scale to AC Power

§ It is recommended to use only the

included AC adapter for optimal

performance and safety.

§ Insert plug into the jack

(located on back of scale)

§ Plug the AC adapter into an electrical

outlet

! LISTED power supply 11 V–21 V

compliant with NEC Class 2 output.

Below-Balance/Under-Scale

Weighing

A port for a below-balance weighing

hanger is located on the bottom of

the balance/scale.

§ Open the cover plate on the bottom

of the balance/scale.

§ Attach the sample (e.g., using a sus-

pension wire) to the hanger.

$ Install a shield for protection against

drafts if necessary.

Installing the Battery

(not for models VIC-303, VIC-123,

VIC-4MG, VIC-2MG)

$ Batteries are not included with the

equipment supplied

! Use only commercially available 9V

batteries.

! If you use a rechargeable battery,

recharge it with an external battery

charger.

§ Lay the balance/scale on its side

§ Open the battery compartment:

remove the compartment cover

§ Install the battery in the compart-

ment

$ Make sure the polarity is correct.

! Close the battery compartment: slide

the cover into position until it snaps

into place

! Do not throw away used batteries

with normal household waste.

Rechargeable batteries contain toxic

materials and must be disposed of in

accordance with local waste disposal

regulations.

Leveling the Balance/Scale

(only for models VIC-303,

VIC-123, VIC-4MG, VIC-2MG)

§ Always level the balance/scale

again any time after it has been

moved to a different location.

Example: moving bubble from R to L

§ Turn the feet as shown in the dia-

gram until the air bubble is centered

within the circle of the level indicator.

> In most cases this will require several

adjustment steps.

Removing Weights for

Calibration/Span Adjustment

(only for models VIC-612, VIC-212,

VIC-711, VIC-511, VIC-303,

VIC-123, VIC-4MG, VIC-2MG)

§ Grasp the tab to turn and remove

the weight compartment.

$ Follow instructions on page 12 for

calibration/span adjustment.

5

Basic Weighing Function

Features

– Zeroing the balance

You can zero the balance/scale within the entire weighing

range, up to the maximum capacity.

Preparation

§ Switch on the balance/scale: press the (ON/OFF) key

§ If necessary, zero the balance/scale: press the (ZERO) key

$ If necessary, change the configuration settings:

see the chapter entitled “Configuration”

$ If desired, load the factory settings:

see the chapter entitled “Configuration,” menu item 9.– 1

Additional functions:

$ Switching off the balance/scale: press the (ON/OFF) key

$ Battery operation: automatic shut-off after 2,5 or 10 min-

utes; see chapter on configuration. Example: 2 minutes.

If the weight readout remains unchanged and no keys are

pressed for at least two minutes, the battery symbol

“ “ starts flashing. After another 2 seconds, the

balance shuts off automatically, unless a key is pressed.

Description of the Keys

(ON/OFF) On/off key: switches the balance/scale on and

off or switches it to the standby mode.

Battery operation: on; turns backlight on; off

(ZERO) Zeros the balance; press and hold 2 seconds:

opens the application menu

(CAL) Starts calibration/adjustment

(F) Starts an application program;

Scrolling in application menu, configration

menu and calibration menu

(ENTER) Confirms the selected setting;

Exits application, configuration & calibration

menu if key is pressed and held for more than

2 seconds.

(PRINT) Generates a printout or data output

Operation

Example: Determine weight of sample

Step Key (or instruction) Display

1. Switch on the balance/scale (ON/OFF)

Self-test runs

Display: Software version

r 31.01

2. Open the in-use cover and leave open

while weighing

3. Place container on the balance/scale 52.0 g

(in this example, 52 g)

4

. Zero the balance/scale (ZERO)

0.0 g

5. Place sample in container on balance/scale 150.2 g

(in this example, 150,2 g).

6

Toggling between Weight Units

With this application program you can toggle the display of a weight value back and forth between two weight units (see table below).

Example: Toggle weight unit from pounds [lb] (application) to grams [g] (basic unit)

Step Key (or instruction) Display

1. Select application program (ZERO) > 2 sec

2. Select Toggling between Weight Units (F)

3. Confirm unit (ENTER)

4. Select weight unit; in this example: “5. Pound” (F) repeatedly

(see table below)

5. Confirm weight unit (pounds) (ENTER)

6. Place sample on balance/scale

7. Toggle weight unit (F)

Menu code Unit Conversion factor Display

1. user* Grams 1.00000000000 o

2.grams (factory setting) Grams 1.00000000000 g

4.carat Carats 5.00000000000 o

5.Pound Pounds 0.00220462260 lb

6.ounce Ounces 0.03527396200 oz

7.tryo Troy ounces 0.03215074700 ozt

8.tl.hon Hong Kong taels 0.02671725000 tlk

9.tl.sin Singapore taels 0.02645544638 tl

10.tl.ta Taiwanese taels 0.02666666000 tl

11.grai Grains 15.4323583500 GN

12.peny Pennyweights 0.64301493100 dwt

15.tl.ch Chinese taels 0.02645547175 tl

22.pdoz lb/oz 0.03527396200 lb:oz

23.newt Newtons 0.00980665000 N

* User-defined conversion is customer selectable with RS-232 or USB program option.

Application Programs

7

Purpose

With the Counting program you can determine the number of parts or items.

Example: Determine the number of uncounted parts; weigh in the selectable reference sample quantity (in this example: 20)

Step Key (or instruction) Display

1. Select application program (ZERO) > 2 sec

2. Select Counting (F) repeatedly

3. Confirm setting (ENTER)

Symbol “ “ on the display: application is active

4. Place empty container on the balance/scale

5. Zero the balance/scale (ZERO)

6. Place reference sample quantity (20)

on the balance/scale

7. Select reference sample quantity:

in increments of 1 (1, 2, 3, ..., 99) or (F) repeatedly (briefly) or

in increments of 10 (10, 20, 30, ...,100) (F) > 2 sec.

8. Confirm selected reference sample quantity (ENTER)

9. Place uncounted parts on balance/scale

10. Toggle display between mean piece weight,

total weight, and quantity (F) repeatedly

11. Unload the balance/scale

12. Counting application: clear the reference value (ENTER) > 2 sec

13. Reactivate Counting (if no other (F)

application program has been selected)

14. Repeat procedure starting from Step 5.

Counting

8

Purpose

This application program allows you to obtain weight readouts in percent which are in proportion to a reference weight.

Example: Determine an unknown percentage; store the weight on the balance/scale as the reference percentage (100%)

Step Key (or instruction) Display

1. Select application program (ZERO) > 2 sec

2. Select Weighing in Percent (F) repeatedly

3. Confirm setting (ENTER)

Symbol “ “ on the display: application is active

4. Place empty container on the balance/scale

5. Tare the balance (ZERO)

6. Place the reference weight for 100% on the

balance/scale

7. If desired, change the number of decimal places

displayed:100.0%,100.00% or 100% (factory setting) (F) repeatedly

8. Confirm selected no. of decimal places (ENTER)

9. Place unknown weight on the balance/scale

10. Toggle display between weight and percentage (F) repeatedly

11. Unload the balance/scale

12. Weighing in Percent application:

clear the reference percentage (ENTER) > 2 sec

13. Reactivate Weighing in Percent (if no other (F)

application program has been selected)

14. Repeat procedure starting from Step 5.

Weighing in Percent

9

Purpose

“Holds” the displayed value; also, the display will be locked for 5 seconds after removing the sample from the pan.

Example: Determine weight of oversized sample

Step Key (or instruction) Display

1. Select application program (ZERO) > 2 sec

2. Select Hold Display (F) repeatedly

3. Confirm setting (ENTER)

Symbol “ “ on the display: application is active

4. If necessary: zero the balance/scale (ZERO)

5. Place oversized sample on balance/scale

6. Start application program (F)

Symbol “ “ flashes on the display:

the weight value is locked

7. Unload the balance/scale: the weight value

remains displayed for a further 5 seconds; or

8. Zero the balance/scale (ZERO)

9. End the Display Hold application (ENTER) > 2 sec

10. Reactivate Display Hold (if no other (F)

application program has been selected)

11. Repeat procedure starting from Step 5.

“Hold” Display

10

Purpose

With this application program you can add up successive weight values exerding capacity of balance/scale.

Example: Totalizing weight values

Step Key (or instruction) Display

1. Select application program (ZERO) > 2 sec

2. Select Totalizing (F) repeatedly

3. Confirm setting (ENTER)

Symbol “ “ on the display: application is active

4. If necessary: zero the balance/scale (ZERO)

5. Place sample on balance/scale (in this example, 380 g)

6. Store value in memory. Total weight is displayed (ENTER)

steadily; symbol flashes.

7. Remove sample from balance/scale

8. Place the next sample on the balance/scale

(in this example, 575 g)

9. Store value in memory. Totalized stored weight (ENTER)

is displayed; symbol flashes.

Note: symbol remains on indicating stored

value in memory until cleared

10. To view the current weight for 2 seconds (F)

(if a printer is connected, a printout is generated)

11. Clear totalizing memory (F) > 2 sec

(if a printer is connected, total is printed)

12. End Totalizing (ENTER) > 2 sec

13. Reactivate Totalizing (if no other (F)

application program has been selected)

(if a printer is connected, total is printed).

14. Repeat procedure starting from Step 6.

Totalizing

11

Purpose

Use this application program to determine the specific gravity of a sample. The result is displayed with one decimal place.

Beaker and wire not included with balance/scale.

Example: Determine the specific gravity of a solid.

Step Key (or instruction) Display

1. Select application program (ZERO) > 2 sec

2. Select Specific Gravity (F) repeatedly

3. Confirm setting (ENTER)

Symbol “ “ on the display: application is active

4. If necessary, zero the balance/scale (ZERO)

5. Start application program (F)

6. Confirm the display, “airval” (ENTER)

7. Determine weight of the sample in air:

place sample on the balance/scale

8. Store weight-in-air value (ENTER)

9. Remove sample from balance/scale

10. Determine weight of sample in liquid:

connect wire and set up beaker

11. Confirm the display “Water” (ENTER)

12. Place sample in liquid

13. Store the weight-in-liquid value and view the result (ENTER)

14. Clear the display (ZERO)

15. Exit the Specific Gravity application (ENTER) > 2 sec

16. Reactivate Specific Gravity (if no other (F)

application program has been selected)

17. Repeat procedure starting from Step 5.

Specific Gravity

12

Calibration is recommended after initial installation and each time the balance/scale is moved.

Features

Calibration/adjustment can be performed only when:

– there is no load on the balance/scale,

– the balance/scale is zeroed, and

– the internal signal is stable.

If these conditions are not met, an error message

is displayed.

Example: Calibrate/adjust span of the balance/scale (here: model VIC-5101)

Step Key (or instruction) Display

1. Switch on the balance/scale (ON/OFF)

2. Zero the balance/scale (ZERO)

3. Start calibration (CAL)

The preset calibration weight is displayed without

the weight unit (in this example, 5000 g)

4. To select a different calibration weight value (F) repeatedly

5. Confirm calibration weight value and (ENTER)

start calibration/span adjustment

After the zero point is stored, the required

calibration weight flashes on the display.

6. Place the required calibration

weight on the balance/scale

The readout stops flashing if the weight is

applied within the defined time limit and tolerance.

If the weight value is accepted, the display stops

flashing and the stability symbol appears

on the display.

7. Remove the calibration weight

8. Calibration has been completed

Calibration/Span Adjustment

The weight required for calibration/adjustment is displayed.

Standard calibration weights for selected models: to remove,

see instructions on page 4.

Press (F) to select a different weight value.

To cancel the procedure: press and hold the (ENTER) key

(> 2 sec.).

13

To configure the balance/scale; i.e., adapt the balance/scale to individual requirements.

Step Key (or instruction) Display

1. Switch off the balance/scale (ON/OFF)

2. Switch on the balance/scale and (ON/OFF)

while all segments are displayed (ZERO) briefly

Navigation in the Setup Menu

Key Press briefly Press and hold

(ENTER) Menu level: move to the right (cyclical) Confirm setting

(F) Menu item: Scrolling –

(ZERO) Menu level: Move to the left Save settings and exit Setup

Parameter Settings (Overview) ο Factory setting √ User-defined setting

Setup 1 Weighing 1.1. Adapt filter 1.1.1 Very stable conditions

menu 1.1.2 ο Stable conditions

1.1.3 Unstable conditions

1.1.4 Very unstable conditions

1.2. Application filter 1.2.1 ο Final readout

1.2.2 Filling

1.3. Stability range 1.3.1 1/4 digit

1.3.2 1/2 digit

1.3.3 1 digit

1.3.4 ο 2 digits

1.3.5 4 digits

1.5. Calib./adjust./linearization: 1.5.1 ο Calibration/adjustment

Function of the (CAL) key 1.5.2 Linearization: for service personnel only

1.5.3 Key blocked

1.6. Auto zero 1.6.1 ο On

1.6.2 Off

1.7. 1st weight unit, or 2nd unit in 1.7.1 User-defined unit; see

Toggle Weight Units app. to 1.7.23 “Toggling between Weight Units”

5. and 6. Only relevant with built-in data interface: see corresponding interface description

8. Additional 8.1. Block key functions 8.1.1 All keys blocked except for (ON/OFF)

functions and (ZERO)

8.1.2 ο All keys unblocked

8.2. Automatic shut-off 8.2.1 ο After 2 minutes

8.2.2 After 5 minutes

8.2.3 After 10 minutes

9. Reset menu 9.1. Factory settings 9.1.1 Restore

9.1.2 ο Do not restore

Configuration (Setup Menu)

14

Error codes are shown on the main display for approx. 2 seconds. The program then returns automatically to the previous mode.

Display/Problem Cause Solution

No segments appear No power available Check the power supply

on the display

The AC adapter is not plugged in Plug in the AC adapter

Battery is drained Replace battery; recharge battery using

external charger

oL The load exceeds the balance/scale Unload the balance/scale

capacity

UL Weighing pan not in place Place the weighing pan

on the balance/scale

Something is touching Move the object that is

the weighing pan touching the weighing pan

disErr Display overflow: Reduce load on the balance/scale

Value cannot be shown

on the display

calErr Calibration parameter not met; e.g.: Calibrate only when zero is displayed

– Balance/scale not zeroed Press (ZERO) to tare the balance/scale

– Balance/scale is loaded Unload the balance/scale

appErr Weight is too light or Increase the weight on the balance/scale

there is no sample on the balance/scale

with application in use

PrtErr Data interface for Contact the Acculab

printing is blocked customer service center

bal.Err Balance/scale loaded or defecteive Unload balance/scale before switching on

when power was turned on or contact Acculab custumer service

sys.Err Balance/scale defective Contact Acculab custumer service

Max. weighing capacity is less The balance/scale was switched on Place the weighing pan on the

than indicated under “Specifications” without the weighing pan in place balance/scale and press (ON/OFF)

The weight readout is obviously wrong The balance/scale was not calibrated/ Calibrate/adjust the balance/scale

adjusted before weighing

Balance/scale not zeroed Zero the balance/scale

If any other errors occur, contact your local Acculab customer service center.

Error Codes

15

Specifications

Model VIC-303 VIC-123 VIC-4MG VIC-2MG VIC-612 VIC-412 VIC-212

Weighing capacity g 300 120 410 210 610 410 210

Readability g 0.001 0.001 0.005 0.005 0.01 0.01 0.01

Tare range (subtractive) g 300 120 410 210 610 410 210

Linearity ≤±g 0.004 0.003 0.01 0.01 0.03 0.03 0.035

Operating temperature range 10°C to 30°C (273°K to 303°K; 50°F to 86°F)

Stabilization time (average) s 2.5 2.5 2.5 2.5 2 2 2

Adaptation to ambient conditions By selection of 1 of 4 optimized filter levels; display update: 0.1–0.8 (depends on filter level selected)

Calibration weight g 200 (F1) 100 (F1) 200 (F1) 200 (F2) 200 (F2) 200 (F2) 200 (M1)

Net weight, approx. kg 1.3 1.2 1.3 1.3 1.35 1.35 1.2

Pan size mm 97 d 97 d 97 d 97 d 142x130 142x130 97 d

Power source/voltage/frequency AC adapter, 230 V or 115 V, +15% to – 20%, 48–60 Hz

Power consumption (average) W 1 1 1 1 0.75 0.75 0.75

Hours of operation w/ 9V battery:

– Alkaline (approx.) h – – – – 11 11 14

– Rechargeable, fully ch.,

(NiMH), avg. h – – – – 2.5 2.5 4

Model

VIC-5101 VIC-3101 VIC-1501 VIC-711 VIC-511 VIC-10KG VIC-6KG VIC-4KG

Weighing capacity g 5100 3100 1500 710 510 10100 6100 4100

Readability g 0.1 0.1 0.1 0.1 0.1 1 1 1

Tare range (subtractive) g 5100 3100 1500 710 510 10100 6100 4100

Linearity ≤±g 0.2 0.2 0.2 0.2 0.2 2 2 1

Operating temperature range 10°C to 30°C (273°K to 303°K; 50°F to 86°F)

Stabilization time (average) s 2 2 1.5 1.5 1.5 1.5 1.5 1.5

Adaptation to ambient conditions By selection of 1 of 4 optimized filter levels; display update: 0.1–0.8 (depends on filter level selected)

Calibration weight kg 5 (F2) 2 (F2) 1 (M1) 0,2 (M2) 0,2 (M2) 5 (M1) 5 (M2) 2 (M2)

Net weight, approx. kg 1.1 1.1 1.1 1.25 1.25 1.1 1.1 1.1

Pan size mm 142x130

Power source/voltage/frequency AC adapter, 230 V or 115 V, +15% to – 20%, 48–60 Hz

Power consumption (average) W 1 1 0.75 0.75 0.75 0.75 0.75 0.75

Hours of operation w/ 9V battery:

– Alkaline (approx.) h 11 11 14 14 14 14 14 14

– Rechargeable, fully ch.,

(NiMH), avg. h 2.5 2.5 4444 44

Overview

16

Product Order No.

Data interface, mounting kit

– RS-232 interface with cable YADAP-RS

– USB interface with cable YADAP-USB

Data printer YDP03-0CE

Lock-down capability LC-1

(for anti-theft locking device)

Calibration weights

– for VIC-5101 (5 kg; F2) YCW6548-00

– for VIC-3101 (2 kg; F2) YCW6248-00

– for VIC-1501 (1 kg; M1) YCW615-00

– for VIC-10KG (5 kg; M1) YCW655-00

– for VIC-6KG (5 kg; M2) YCW656-00

– for VIC-4KG (2 kg; M2) YCW626-00

– for weight compartment,

(right side), (100 g; F1) 69V00006

Product Order No.

In-use cover:

– for models without glass draft shield 69V00001

– for models with glass draft shield 69V00002

Round glas draft shield 69V00003

(25 mm high)

Weighing pan: – Round 69V00004

– Rectangular 69V00005

Leveling feet (set of one

adjustable foot and one fixed foot) 69V00007

Covers: (set of small parts) 69V00008

– Battery compartment

– Interface port

– Weight compartment

Accessories (Options)

C Marking

The balance/scale complies with the following EC Directives

and European Standards:

Council Directive 89/336/EEC “Electromagnetic

compatibility (EMC)”

Applicable European Standards:

Limitation of emissions:

In accordance with product standard EN 61326-1 Class B

(residential area)

Defined immunity to interference:

in accordance with product standard EN 61326-1

(minimum test requirements, non-continuous operation)

Important Note:

The operator shall be responsible for any modifications to

Acculab equipment and must check and, if necessary, correct

these modifications.

On request, Acculab will provide information on the minimum

operating specifications (in accordance with the Standards

listed above for defined immunity to interference).

73/22/EEC “Electrical equipment designed for

use within certain voltage limits”

Applicable European Standards:

EN 60950

Safety of information technology equipment including electrical

business equipment

EN 61010

Safety requirements for electrical equipment for measurement,

control and laboratory use

Part 1: General requirements

If you use electrical equipment in installations

and under ambient conditions requiring higher safety standards,

you must comply with the provisions as specified in the

applicable regulations for installation in your country.

Page is loading ...

Programas de aplicación

Conmutación de unidades

Con este programa de aplicación puede indicarse el valor de peso en una unidad seleccionada (ver tabla) y en gramos.

Ejemplo: conmutar unidad: de libras [lb] (aplicación) a gramos [g] (unidad básica)

Paso Pulsar tecla Lectura

1. conmutar programa aplicación (ZERO) pulsión larga

2. seleccionar unidad a conmutar (F)

3. confirmar ajuste (ENTER)

4. seleccionar unidad peso; aquí “5. libras” repetidam (F)

(ver tabla, abajo)

5. confirmar unidad libras (ENTER)

6. poner muestra

7. conmutar unidad peso (F)

Item de menú Unidad Conversión Lectura

1. user* Gramos 1,00000000000 o

2.grams (ajuste fábrica) Gramos 1,00000000000 g

4.carat Quilates 5,00000000000 o

5.Pound Libras 0,00220462260 lb

6.ounce Onzas 0,03527396200 oz

7.tryo Onzas Troy 0,03215074700 ozt

8.tl.hon Taeles Hongkong 0,02671725000 tl

9.tl.sin Taeles Singapur 0,02645544638 tl

10.tl.ta Taeles Taiwan 0,02666666000 tl

11.grai Granos 15,4323583500 GN

12.peny Pennyweights 0,64301493100 dwt

15.tl.ch Taeles China 0,02645547175 tl

22.pdoz lb/oz 0,03527396200 lb:oz

23.newt Newton 0,00980665000 N

* = Unidad definida por el usuario, cargable con progr. PC en la balanza mediante interfaz opcional RS-232, o bien USB.

66

Page is loading ...

Copyright by Acculab.

may be reprinted or translated in any form

or by any means without the prior written

permission of Acculab.

The status of the information, specifications

and illustrations in this manual is indicated

by the date given below.

Acculab reserves the right to make changes

to the technology, features, specifications

and design of the equipment without notice.

Status:

July 2005, Acculab

W1A000 · KT

Publication No.: WVI6006-p05071

ACCULAB North America

131 Heartland Blvd.

Edgewood, NY 11717

USA

800-656-4400

International

+1.631.254.4299

ACCULAB Europe

Weender Landstrasse 94-108

37075 Goettingen, Germany

+49.551.308.1667

ACCULAB UK c/o Sartorius Ltd

Longmead Business Centre

Blenheim Road, Epsom

Surrey, KT19 9QQ

United Kingdom

+44.1372.737100

ACCULAB China

No.8 Pingeui West Road, Wang Jing

Industrial Zone

Chao Yang District

100102 Beijing

+86.10.6439.2552

ACCULAB ASIA-PACIFIC

Unit 1110-12, LU Plaza

2 Wing Yip Street, Kwon Tong

Kowloon, Hong Kong

www.acculab.com

www.acclulab-europe.com

Acculab 98648-013-61 Operating instructions

Acculab 98648-013-61 Operating instructions

in other languages

Related papers

Other documents