2. Computers & electronics
  3. Audio & home theatre
  4. DVD players
  5. JVC
  6. HR-XV1EU-Y
HR-XV1EU-Y

JVC HR-XV1EU-Y User manual

  • Hello! I am an AI chatbot trained to assist you with the JVC HR-XV1EU-Y User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
DVD PLAYER
Hi-Fi VIDEO
CASSETTE
RECORDER
USER’S GUIDE
For model:
HR-XV1EU
DIGITAL VIDEO
LPT0715-001A
2A73501AE Cover 4/17/02, 8:23 PM1
2
SAFETY FIRST
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
Safety Precautions
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording
is not possible with this model.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS
recordings with regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
•SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufac-
tured under licence from Gemstar Development Corporation.
PAL
CAUTION
When you are not using the recorder for a long period of time, it is recommended that you disconnect the
power cord from the mains outlet.
Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock
or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal
lead or aerial.
CAUTION:
A DVD/VCR IS A CLASS 1 LASER PRODUCT. HOWEVER THIS DVD/VCR USES A VISIBLE LASER BEAM
WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE PLAYER CORRECTLY AS INSTRUCTED.
THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE DVD/VCR.
WHEN THIS DVD/VCR IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO
THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS DVD/
VCR.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
• Use only discs marked with the following.
DVD
[8 cm disc/12 cm disc]
Video CDs/Audio CDs
[8 cm disc/12 cm disc]
DIGITAL VIDEO
IMPORTANT
Please read the various precautions on page 2 and 3 before installing or operating the recorder.
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in
any literary, dramatic, musical, or artistic work embodied therein.
CLASS 1
LASER PRODUCT
2A73501AE(02-05) 4/17/02, 8:23 PM2
3
Safety Precautions
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow
for ventilation (10 cm or more on both sides, on top and at the rear.)
When discarding batteries, environmental problems must be considered and the local rules or laws governing
the disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in damage to the recorder, remote control or video
cassette.
1.
DO NOT place the recorder ...
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2.
DO NOT block the recorder’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get
out.)
3.
DO NOT place heavy objects on the recorder or remote control.
4.
DO NOT place anything which might spill on top of the recorder or remote control.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
5.
DO NOT expose the apparatus to dripping or splashing.
6.
DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any containers filled
with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this
unit.
7.
DO NOT place any naked flame sources, such as lighted candles, on the apparatus.
8.
AVOID violent shocks to the recorder during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under
extremely humid conditions-just as water droplets form in the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the tape. In conditions where condensation may occur,
keep the recorder turned on for a few hours to let the moisture dry.
Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-
speed video recorder.
The STANDBY/ON button does not completely shut off mains power from the unit, but switches operating
current on and off. “
” shows electrical power standby and “ I ” shows ON.
For ItaIy:
“It is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95 published in
the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95”
2A73501AE(02-05) 02.4.22, 12:54 PM3
4
Features
Video Cassette Recorder
• High Quality (HQ) Images
• On-Screen Displays (OSD)
• Nicam Hi-Fi Stereo Audio
Recording and Playback
• ATS- Automatic Tuning System
• CATV Tuner with Hyperband
• 80 Memories for presets
• Auto Time Setting
• 30 Minutes Back-Up in case of
Power failure
• 6 rotary Heads (4 Video Heads
2 HiFi Audio Heads)
• Long play
• VPS/PDC system
• Timer Recording of up to 8
Programs per Month
• S
HOWVIEW
®
-rapid timer
programing
• Instant Timer Recording (ITR)
• Video index Search System
• Slow Motion
• NTSC Video Cassette Tape
Playback on PAL TV
• Real-Time Tape Counter with
ZERO RETURN-Function
• Digital AUTO Tracking (ATR
Function)
• Repeat/Scene Repeat
• On-Screen Display in 3
Languages
• AV-Front input jacks
• 2 Scart sockets for Premiere
• CE Symbol guaranteeing
Compliance to Currently
Effective European Standards
DVD Player
• Digital Audio Jack (Coaxial)
• Multi-Language
• Multi-Angle
• Surround audio
• Repeat Playback
• Memory/Random Playback
• Zoom
• Video Aspect Ratio
• Parental Control
• 3 Scenes memory
• Digital (Optical or Coaxial) output
for Dolby Digital (AC-3) and DTS
• Playback of DVD, Video-CD and
Audio-CD
• PAL & NTSC DVDs playback
• A-B Repeat playback
• MP3 CD playback
* This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be authorized by Macrovision Corporation or other rights owners
and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation or other rights owners. Reverse engineering or disassembly is prohibited.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
* Certain audio features of this product manufactured under license from Desper Products,Inc. Spatializer and
the circle - in - square device are trademarks owned by Desper Products,Inc.
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may
infringe the rights of copyright owners and be contrary to copyright laws.
2A73501AE(02-05) 02.4.22, 12:54 PM4
5
Contents
Safety Precautions ........................................... 2
Features ........................................................... 4
Contents ........................................................... 5
Parts and functions .......................................... 6
Display ............................................................. 7
Remote control ................................................. 8
Connections and Installation .......................... 10
Playback connection ...................................... 11
Before using your unit
Recording a TV Program ................................ 28
Instant Timer Recording (ITR) ........................ 30
ShowView
®
-Recording ................................... 31
Timer-Recording ............................................ 33
Recording
Advanced function of VCR section
Loading and Unloading a Cassette Tape ....... 22
Cassette tape playback .................................. 23
Special playback/Playback sharpness ........... 24
Repeat Playback ............................................25
Counter Display.............................................. 26
Video Index Search System ...........................27
Tape playback operation
Setting the TV to the AV-Channel ................... 13
Setting the On-screen language .................... 14
ATS Automatic Tuning System and
Auto Time /Date Setting ................................. 15
ATS................................................................. 16
Setting the Time and Date .............................. 19
Manual TV station presetting .......................... 20
Setting up the VCR section
DISC............................................................... 40
Setting setup language .................................. 41
Playback procedure........................................ 42
Special playback ............................................ 43
DVD Picture Signal Selection/Zooming .......... 44
Repeat playback............................................. 45
Memory playback/Random playback ............. 46
MP3 Playback ................................................ 47
Changing soundtrack language /
Changing Subtitles language ......................... 48
Changing angles / Title selection /
DVD menu ...................................................... 49
Disc playback operation
Parental control .............................................. 50
Setting menu language .................................. 52
Setting audio soundtrack language ................ 53
Setting subtitle language ................................ 54
Setting the aspect ratio of TV screen /
Setting on Screen display .............................. 55
Setting Audio .................................................. 56
Setting Operation ........................................... 57
Selecting the sound enhancement (E.A.M.)/
Setting Background/Setting Screen Saver ..... 58
Setting initial setup/output sound
conversion table ............................................. 59
Status display of Disc ..................................... 60
Table of languages ......................................... 61
Advanced function of DVD section
Problems and troubleshooting ....................... 62
Video head cleaning....................................... 63
Specifications ................................................. 64
Additional information
Detailed Description of the VPS/
PDC Function ................................................. 35
NICAM/German A2 Stereo Recording
and Playback .................................................. 36
Audio Mixing ................................................... 38
Duplicating a Video Tape ................................ 39
2A73501AE(02-05) 4/17/02, 8:23 PM5
6
SCART-socket
(for VCR/DECODER)
SCART PRISE PERITEL
Parts and functions
Front
STOP button
Rear
AC power cord
PLAY button
OPEN/CLOSE button
Disc tray
POWER
button
DVD COAXIAL DIGITAL
AUDIO OUT jack
RF IN jack
PR +/– buttons
AUDIO (L/R)/
VIDEO IN jacks
FF (Fast Forward) button
Remote sensor
EJECT button
VCR indicator
VCR/DVD mode selector button
Cassette Loading Slot
REW (Rewind) button
REC button
DVD indicator
DVD AUDIO (L/R) OUT jacks
RF OUT jack
Display window
SCART-socket
(for TV-RGB/Composite)
DVD S-VIDEO OUT jack
DVD OPTICAL
DIGITAL AUDIO
OUT jack
2A73501AE(06-11) 4/17/02, 8:22 PM6
7
No. Display Description
VCR mode
1
2
3
4
5
6
1 2
3
4
6
5
Display
7
8
9
10
VCR
DVD
CD
10 : 00
01 : 00
2
A1/A2/A3
TRK
REC
CH 2
Playback (lights) / Auto resume (flashes)
Still picture
DVD disc is inserted.
CD is inserted.
Clock display (colon[ : ] flashes)
Counter display by hour/minute at VCR/DVD / by minute/second at CD
Track number display for CD
TV channel position display
External input display
Timer recording display
Video tape is in the unit
Track display for CD
Normal recording display (flashes during
Instant Timer Recording - ITR
)
Note:
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.
78
9
10
Display window
2A73501AE(06-11) 4/17/02, 8:22 PM7
8
Remote control
Page
TV/VCR/DVD switch
Switch to operate TV or VCR or DVD 14,41
Power on/off 14
Turn the connected TV on or off 8
DVD MENU Display menu of DVD software 49
MEMORY Index for DVD 46
RETURN Remove DVD set up menu 50
OPEN/CLOSE Open or Close the tray 42
DISPLAY Change the front Display mode 26
A.TRK Digital AUTO TRACKING 24
SUB TITLE Set Subtitle of a DVD disc 48
C. RESET Reset the counter to 00:00 26
ANGLE Change playback angle of a DVD disc 49
ZERO RETURN
Stop the tape when the counter reaches 00:00
26
(SP/LP) Sets the tape speed for recording 28,30,39
PLAY MODE Select playback mode 45,46
ZOOM Zoom (for DVD playback) 44
TITLE Select title of a DVD disc 49
REPEAT A-B Repeat playback between A and B (DVD/CD) 45
0-9 Direct channel selection of TV 28,30
Input setting 15~18,31,33,46,47
Enter a password 50
AUX Scart input or AV-Front input 34,39
PROG. S
HOWVIEW-Recording 31
Confirmation of Timer-Recording 34
•
Set the unit to start recording at a preset time.
32,34
TV ∏ (INPUT) Switch the connected TV to external mode 8
TV/VCR Switches between TV and VCR 29
TV @ +/– Adjust the connected TV’s volume 10
8 Rewind/Review playback 23,24,43
1 Playback 23,42,47
9 Fast Forward/Forward search playback 23,24,43
2 Recording 28,30,39
3 Stop 23,42,47
4 Still picture/Recording pause on/off 24,28,39,43
SKIP 6/7 Skip chapter to forward or reverse direction 43
INDEX 6/7 Search for the INDEX mark of a tape 27
TV/VCR PR +/– Select channel of the connected TV or VCR
8,28,30,39
C/D Cursor buttons
SET –/+ Setting buttons 32~34
Manual tracking buttons in playback mode 24
B/A Cursor buttons - To move Up in the VCR menu
you press the A. To move Down in the VCR
menu you press the B.
OK
Enter information in the menu/Select option in the menu
SET UP MENU Display menu of setup 14~21,41,50~59
CANCEL Delete Timer program 34
Cancel input data in the setting mode
18,21,46~50
OSD Display VCR or DVD operation status 28~30,60
A.MONITOR Switches sound 37,38
Change sound track language of DVD 48
SLOW Slowmotion playback 24,43
SKIP SEARCH Skip the unwanted short material of a tape 24
JVC TV Remote Control
This Remote can control some functions
(
, NUMBER (0-9), TV ∏, TV @ +/–,
TV PR +/– and OK) of a remote controllable
JVC TV by slide TV/VCR/DVD switch to TV.
NOTE:
• It’s not possible to operate a unit not
equipped with a remote sensor.
• This Remote can control a JVC TV only.
• When you operate the VCR or DVD, the
TV/VCR/DVD switch must be slided to
VCR/DVD again. Otherwise the DVD/
VCR may not operate properly.
• Since this unit is combined type of DVD
and VCR, the remote code of DVD is
individual. So please note that the DVD-
keys on the RCU of the other JVC
RECEIVER/TV is not effective for this unit.
2A73501AE(06-11) 4/17/02, 8:22 PM8
9
Remote control
12 3
Replace the compartment
cover.
Install two "AA" batteries (not
supplied),
paying attention to the
polarity diagram in the battery
compartment.
Open the battery compart-
ment cover in the direction of
the arrow.
How to install the batteries
Use micro batteries type R6.
Distance of Remote
Control Operation
Battery precautions
The precautions below should be followed when using batteries in this device:
1.Use only the size and type of batteries specified.
2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
Change the custom code for remote control
If you operate this DVD/VCR with another JVC’s VCR simultaneously arranging them side by side, the both
recorders will react to this remote control. In this case, you can change the remote control and DVD/VCR to
other frequency (“ ”). Then you can operate only this DVD/VCR with this changed remote control.
When you purchased, the DVD/VCR and remote control have been set to the frequency-“ ”.
Example: Change frequency to
Remote control:
While holding VCR, press 2 (code: b) of Number keys.
(in case of code: A, press 1). Then press OK.
DVD/VCR:
In the POWER off mode, press and hold PLAY for
more than 5 seconds. The current code (“A” or “b”) will
appear on the display. Then press 3 on the remote
control. The current code of the remote control will be
transmitted to the unit and the unit will be adjusted to
the transmitted code. Then the code will disappear
after approx. 4 seconds.
NOTE:
• If the remote control has been set to b, the DVD/VCR also must be set to b. Otherwise, the DVD/VCR can not
be operated with this remote control.
• To reset to “A”, repeat above procedure. However press 1 instead of 2.
Effective angle:
approx. 60°
approx.
5m
Point the remote
control directly at the
remote sensor.
2A73501AE(06-11) 4/17/02, 8:22 PM9
10
Connections and Installation
Connect your DVD/VCR to your home's antenna and to your TV-set as shown in the illustration.
When you have finished these connections you connect your DVD/VCR to the 230 V / 50 Hz mains.
TV
AC power cord 230V/50 Hz
DVD/VCR
Antenna-Input
To Scart socket
RF-Input (from
house antenna)
TV Scart Socket (A1)
RF-Output (to TV)
Antenna
Supplied Coaxial cable
In addition to the coaxial cable connection, connect also with scart cable. The picture and sound will be transmitted
best through the scart cable. In this case, the TV need not be tuned to the video recorder. The AV-channel also need
not be tuned. The video recorder switch the television to video operation through the scart cable automatically.
The
stereo-playback is possible in only case through a scart cable!
Connect a TV with the Scart socket
If your TV-set does not switch to video-playback operation automatically, please
turn your TV's video switch to VIDEO position manually.
Scart cable (not supplied)
VCR/DECODER
Scart Socket (A2)
2A73501AE(06-11) 4/17/02, 8:22 PM10
11
Playback connection
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is
dependent on the model and features of each component. Check the Owner's Manual provided with each
component for the location of SCART socket.
Connection to a Satellite Receiver
If a Satellite Receiver is used, we recommend the following configuration:
Connection to a Decoder (for Premiere Programs)
Decoder
RF-Output
SCART-cable (not supplied)
Cable TV-
connection
TV-unit
SCART-cable (not supplied)
DVD/VCR
To record from Satellite Receiver press "AUX" on the remote control of DVD/VCR twice. "A2" will appear
on the front display. Select the desired TV-program at Satellite Receiver.
Connect to a TV with S-Video Output
CLOCK SET
SYSTEM SETUP
LANGUAGE/SPRACHE/LANGUE
AV2 [DEC]
SELECT :
ENTER
:OK
MENU
EXIT
:
Note: Make sure that AV - mode in SYSTEM SETUP - menu has been set
to DEC .
SCART-cable (not supplied)
Satellite
Antenna
Satellite
Receiver
DVD/VCR
TV
SCART-cable (not supplied)
Note:
• The S-VIDEO jack is useful only for DVD section.
• If you use the connection with S-Video Cord, set the "Video Out Select" (P.44) to "Video".
DVD/VCR
TV
S-Video Cord (not supplied)
To Audio (R) Input
To S-Video Input
To Audio (L) Input
S-Video Output
AUDIO Cord (not supplied)
Audio (L) Output
Audio (R) Output
2A73501AE(06-11) 02.4.22, 12:53 PM11
12
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
such as Dolby Digital and DTS by using the Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
Playback connection
Connect to a Stereo Amplifier with Audio Output
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital
cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
• The OPTICAL, COAXIAL jacks are useful only for DVD section.
VHS signal is output only from the SCART-sockets, AUDIO L/R jacks and RF OUT jack.
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
• DTS audio will be output only from the COAXIAL output. To hear DTS audio, DTS-Decoder is necessary.
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
Coaxial digital cable
(not supplied)
AV Amplifier with
built-in various
decoder as above
DVD/VCR
TV
If your DVD/VCR is connected to a stereo amplifier, the video soundtrack can output through the loudspeakers of
the stereo system.
To Audio (L) Input
To Audio (R) Input
TV
AUDIO Cord (not supplied)
Stereo Amplifier
DVD/VCR
Audio (R) Output
SCART-cable (not supplied)
Audio (L) Output
Coaxial digital
Audio Output
SCART-Socket
(for TV-RGB/Composite)
To SCART
input
SCART-cable (not supplied)
To SCART
input
SCART-Socket
(for TV-RGB/Composite)
2A73501AE(12-15) 4/17/02, 8:22 PM12
13
TEST
Setting the TV to the AV-Channel
We recommend that television and DVD/VCR are being connected with a scart cable.
In this case, the setting of AV-channel is not necessary. Picture and sound of video cassette will be transmit-
ted to television through the scart cable automatically. Please read the next page.
•
•
Turn on the TV.
Make sure the power of DVD/VCR has been
turned off.
Press the DVD/VCR’s
(not the one on your remote
control) and keep pressing it until the display shows rF:.
The number next to rF: is the channel in UHF-band to
which you must tune your TV-set.
If there is interference in the picture (you see 2 programs
simultaneously or what is called Ghosts), change the
sending channel in DVD/VCR. To do this, go back to the
step 1. Use PR button on the DVD/VCR to change the
number next to the rF:. Then return to step 2 and tune the
television newly.
1
3
In case of no scart cable connection,
you must set the television to the AV-
channel. Pay attention to the following
notice:
A built-in TV-broadcast in DVD/VCR can
do the video playback through the sup-
plied antenna cable. This broadcast is
sent on UHF, channel 36. To receive this
broadcast, you must tune your televi-
sion to channel 36 in UHF-band.(see
step 2)
In case a broadcast has already sent
to channel 36 in your area or you con-
nect a additional equipment (e.g. Sat-
ellite receiver) with a coaxial cable
(without a scart cable), you must tune
the sending channel in DVD/VCR (see
step 3). In your television store the both
equipment (the DVD/VCR and the sat-
ellite receiver) to 2 different program
positions.
Example: Your satellite receiver is sent
to channel 36. You tune the DVD/VCR
to channel 40 (see step 3).
(If your DVD/VCR is also sent to chan-
nel 36, the interference will occur.)
In your television store the channel 36
to e.g. program position 3 and store the
channel 40 to e.g. program position 4.
Note that the program position 4 must
be suitable for video-playback espe-
cially. Please see the owner's manual
for your television. If the playback pic-
ture is often distored, you must select
the other program position for DVD/
VCR.
Preparation
If you want to use your DVD/VCR, switch
your television to this program position.
Switch your television to the program position on which
the video playback is seen. Start the channel search of
your television until “TEST” appears. Store this tuning in
television like also the case of the reception for normal
television-channels you would store.
2
Press button to turn off the DVD/VCR.
4
Note:
If you receive one TV-program on channel 35, 36 or 37, the interference can be occurred to the built-in TV
channel in DVD/VCR. If you use a scart cable for the transmission of picture and sound, you can cut off the
built-in TV-program. Then the video playback through the supplied antenna cable is not possible any more.
Press PR repeatedly (at step 1) until OFF will appear.(OFF appears after 69 or before 23)
VCR
TEST
1,4
3
2A73501AE(12-15) 4/17/02, 8:22 PM13
14
TIMER REC SET
ATS (AUTO TUNING SYSTEM)
VCR EXTENSION
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : OK
MENU
EXIT
:
VCR SETUP
Setting the On-screen language
NOTES:
• If the unit does not operate prop-
erly, or No key operation (by the unit
and/or the remote control): Static
electricity, etc., may affect the player's
operation. Disconnect the AC power
cord once, then connect it again.
• Both the VCR and the DVD have their
own menu option (See page 41).
• If no buttons are pressed for more than
60 seconds, the MENU screen will
return to normal TV-operation auto-
matically.
You can choose from three different languages (English,
French and German) for the on-screen displays.
3
Press SET UP MENU.
Press or to select the
SYSTEM SETUP option, then
press OK.
If you use the unit for the first time
and press SET UP MENU,
instead of the main menu screen
on the right the “LANGUAGE” set
up menu screen in step 2 may
appear.
Press
or to select the de-
sired language: English (EN-
GLISH), German (DEUTSCH) or
French (FRANCAIS), then press
OK.
1
2
Press or to select the
“LANGUAGE” option, then
press OK.
4
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
Preparation:
• Press the
button to turn on the DVD/VCR.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then
press VCR to select the VCR mode. (The VCR indicator will light)
CLOCK SET
SYSTEM SETUP
LANGUAGE/SPRACHE/LANGUE
AV2 [DEC]
SELECT :
ENTER : OK
MENU
EXIT
:
SELECT :
LANGUAGE/SPRACHE/LANGUE
ENGLISH
DEUTSCH
OK:
OK
FRANCAIS
Turn on your TV and select the AV-
Program position, on which you have
already set your DVD/VCR. (it will
happen automatically by Scart-cable
connection). So you can follow up the
all setting on TV screen.
2A73501AE(12-15) 4/17/02, 8:22 PM14
15
ATS Automatic Tuning System and Auto Time/Date Setting
This VCR has a built-in TV receiver
module. Before you can record a TV
program, all the available TV stations
must be tuned in and preset in the
memory. The ATS function (Automatic
Tuning System) allows all the locally
available TV stations to be automati-
cally stored and sorted according to
the currently effective national station
list. To accomplish this, ATS will need
about 12 minutes. During this period
of time the VCR cannot be used. If you
wish to change the station sequence,
you can later perform a removing
procedure (see page 17).
Preparation:
• Press the
button to turn on the DVD/VCR.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then
press VCR to select the VCR mode. (The VCR indicator will light)
1
Press SET UP MENU. Press
or repeatedly until the dot
before ATS (AUTO TUNING
SYSTEM) blinks. Then press OK.
If no channel setting is done:
Press 1 of number keys at first, and then press SET UP MENU.
2
Press / or / to select
the desired country. Then press
the OK.
3
The ATS setting is completed when “CHANNEL MAPPING”
indication and the current time display appears.
Press SET UP MENU repeatedly until the TV program will be
displayed.
If the CLOCK SET-menu appears and 00:00 appears in the display,
please set the clock manually. In this case, no station transmitting
time data can be received (see page 19).
Note: If ATS is done under the bad receiving condition, one or more
stations may not be found. In this case, set these stations
manually.(see page 20)
TIMER REC SET
VCR EXTENSION
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER
:OK
MENU
EXIT
:
VCR SETUP
ATS (AUTO TUNING SYSTEM)
ATS (AUTO TUNING SYSTEM)
AREA
GERMANY
HOLLAND
AUSTRIA
DENMARK
ITALY
SWISS
SELECT :
OK : OK
MENU
EXIT :
ATS ACTIVE
CHANNEL MAPPING
SELECT
:
SKIP
: CANCEL
CHANGE NAME
:1
MOVE : 2
EXIT
: MENU
1
2 6
9
12
3
4
ARD
HR3
WDR3
MDR3
TM3
ZDF
RTL
SAT1
PRO 7
BR3
SW3
N3
5
7
8
10
11
VCR
2A73501AE(12-15) 4/17/02, 8:22 PM15
16
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then
press VCR to select the VCR mode. (The VCR indicator will light)
1
Press SET UP MENU.
Press or to select
CHANNEL SETUP. Then press
OK.
2
Press or to select
CHANNEL MAPPING. Then
press OK.
3
Press / or / repeatedly
until the TV station to be skipped
blinks.
4
Then press CANCEL.
The number before the canceled
channel (e.g. 12) will be
bracketed.
Canceling the skip function:
Press / or / repeatedly until the skipped TV station blinks,
then press CANCEL.
The brackets will disappear.
5
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
CHANGE NAME
CHANNEL MAPPING
1 ARD
2 ZDF 6 BR3
9 HR3
12 TM3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
10 WDR3
11 MDR3
SELECT
SKIP
EXIT
MOVE
:
:
:
:
:
CANCEL
1
2
MENU
CH TUNING
CHANNEL SETUP
CHANNEL MAPPING
SELECT :
ENTER
:
EXIT
:
OK
MENU
TIMER REC SET
ATS (AUTO TUNING SYSTEM)
VCR EXTENSION
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : OK
MENU
EXIT
:
VCR SETUP
ATS
Skipping unwanted TV stations
(Skip those TV stations that are not
wanted to be selected by pressing the
PR button.)
CHANGE NAME
CHANNEL MAPPING
1 ARD
2 ZDF 6 BR3
9 HR3
12 TM3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
10 WDR3
11 MDR3
SELECT
SKIP
EXIT
MOVE
:
:
:
:
:
CANCEL
1
2
MENU
2A73501AE(16-21) 4/17/02, 8:26 PM16
17
Reassigning TV station positions
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The
VCR indicator will light)
Example: Reassign the TV station under No. 6 to position No. 2.
AT S
1
Select the "CHANNEL MAPPING" in Menu-screen
in the same way as the step 1~2 on page 16. Then
press OK.
2
Press / or /
repeatedly until the TV
station to be reassigned
blinks.
3
Press "2" of number
keys. Then, the TV
station will be moved to
the first display line.
4
Press / or / repeatedly until the position
number blinks to which the selected TV station is to
be moved, then press OK.
WAIT blinks.
The data will be
ordered in the table
newly.
CHANGE NAME
CHANNEL MAPPING
1 ARD
2 ZDF 6 BR3
9 HR3
12 TM3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
10 WDR3
11 MDR3
SELECT
SKIP
EXIT
MOVE
:
:
:
:
:
CANCEL
1
2
MENU
6 BR3
POSITTION
1 ARD
2 ZDF 6
9 HR3
12 TM3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
10 WDR3
11 MDR3
EXIT
MOVE
:
:
:OK
MENU
MOVE CHANNEL
6 BR3
POSITTION
1 ARD
2 ZDF 6
9 HR3
12 TM3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
10 WDR3
11 MDR3
EXIT
MOVE
:
:
:OK
MENU
MOVE CHANNEL
MOVE CHANNEL
POSITION :
MOVE
:OK
EXIT
: MENU
1
2 6
9
12
3
4
ARD
HR3
WDR3
MDR3
TM3
ZDF
RTL
SAT1
PRO 7
SW3
N3
5
7
8
10
11
WAIT
5
After approx. 12
seconds the station
BR3 is set in new
position 2. The ZDF will
be extracted to the first
line.
Now to finish this pro-
cedure and at the same
time set the protruded
station (ZDF) to the
blank position 6, press
SET UP MENU
repeatedly until TV-
station appears.
Or you can of course select another station to set in
the protruded station(ZDF) in step 4.
6
Press SET UP MENU repeatedly until the TV picture
appears on the screen.
6 ZDF
POSITTION
1 ARD
2 ZDF 6
9 HR3
12 TM3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
10 WDR3
11 MDR3
EXIT
MOVE
:
:
:OK
MENU
MOVE CHANNEL
POSITTION
MOVE CHANNEL
1 ARD
2 BR3 6 ZDF
9 HR3
12 TM3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
10 WDR3
11 MDR3
EXIT
MOVE
:
:
:OK
MENU
• A position number(6) will indicated near the protruded
station(ZDF) at the first line.
If any button is not pressed for more than 60 seconds,
this station(ZDF) will be set to this position number(6)
automatically.
2A73501AE(16-21) 4/17/02, 8:26 PM17
18
AT S
Changing TV station names
For a number of TV stations (such as
MTV) no name code will be displayed
because these TV stations do not
provide the necessary information.
You can enter the respective names
yourself. Moreover, unwanted station
codes can be changed by the user.
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then
press VCR to select the VCR mode. (The VCR indicator will light)
Example: MTV is assigned to station No. 10, but the code “MTV” will
not be displayed and will also not appear in the table.
1
Select the "CHANNEL MAPPING" in Menu-screen in the same
way as the step 1 ~ 2 on page 16. Then press OK.
2
Press / or / repeatedly
until the station number position
now to be named will blink.
• If you want to turn over the page
when the blinking spot is in the
left or right edge of on-screen,
press
or repeatedly until
the next page's 12 stations ap-
pears.
3
Press "1" of number keys. The
first display line will change to
"CHANGE BROADCAST
NAME".
4
Press or repeatedly until
the desired character appears.
Then press . Use or to
select the next character. Then
press . Up to four characters
can be used to create a station
name. The character “ ” stands
for a space.
Then press OK.
Each press of will change the screen display as follows.
5
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
12
10
11
OK
SELECT :
NAME
CANCEL
EXIT : MENU
CLEAR :
:
:OK
CHANGE BROADCAST NAME
1 ARD
2 ZDF 6 BR3
9 HR3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
OK
12
10 M
11
SELECT :
NAME
CANCEL
EXIT : MENU
CLEAR :
:
:OK
CHANGE BROADCAST NAME
1 ARD
2 ZDF 6 BR3
9 HR3
3 RTL
4 SAT1
5 PRO 7
7 SW3
8 N3
CHANGE NAME
CHANNEL MAPPING
1
26
9
12
3
4
5
7
8
10
ARD
ZDF BR3
HR3
RTL
SAT1
PRO 7
SW3
N3
11
SELECT
SKIP
EXIT
MOVE
:
:
:
:
:
CANCEL
1
2
MENU
A, B, C, ... X, Y, Z 0, 1, 2, ... 7, 8, 9
–
+
/
•
Note:
When a wrong character is entered,
press CANCEL and enter the correct
character.
2A73501AE(16-21) 4/17/02, 8:26 PM18
19
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then
press VCR to select the VCR mode. (The VCR indicator will light)
Example: Setting the clock to 11:30, 23rd October 2002.
1
Press SET UP MENU. Press
or repeatedly until the dot
before SYSTEM SETUP blinks.
Then press OK. Then press
or repeatedly until the dot
before CLOCK SET blinks. Then
press OK.
2
Press / repeatedly or
number keys until “23” appears.
Then press .
3
Set the month, year, hour and
minute in the same way as the
step 2. Then press .
4
Press or to select “ON” or “OFF”, then press OK. If “ON” is
selected, any required time corrections will be performed
automatically (see left). In this case the personnel of the
appropriate TV station or of Telecom will be responsible for
correcting the time setting. If any
error occurs during such an
adjustment (e.g. switching from
summer time to winter time), your
clock will show the incorrect time.
To set the correct time select
“OFF” and follow the procedure
described above.
• In case of an erroneous input press
to go back to before
step and enter again.
5
Press SET UP MENU repeatedly until the TV picture appears
on the screen.
6
The clock will begin operation and the colon will blink on the
VCR display.
Setting the Time and Date
If the time and date is not be displayed
for some reasons after the ATS
function has been completed, a manual
clock adjustment will be required.
Note:
• In case of a power failure the clock will
continue to operate for another 30 min-
utes with quartz-controlled precision. To
indicate that the power failure has lasted
for an excessive period of time “0:00” will
blink on the display. In this case read-
just time and date.
If the clock does not have been adjusted
yet, the step 1 will appear automatically.
• The clock will only be automatically set
when the VCR is connected to the
Telecom CATV network. All the provided
CATV stations should be stored in the
VCR. This is the case when the ATS
function has been completed. The an-
tenna system must be free of any de-
fects, e.g. there should be no picture
noise. The clock will be re-adjusted every
30 minutes except the period between
23:00 and 1:00 o’clock. In case the total
difference between the indicated time
and the current time is more than 5 min-
utes, the clock will not be corrected. The
switching from winter time to summer
time will be considered.
The clock will not be adjust automati-
cally when:
• timer activated.
• antenna not connected.
• only an outdoor antenna or a satellite
receiver connected.
CLOCK SET
SYSTEM SETUP
LANGUAGE/SPRACHE/LANGUE
AV2 [DEC]
SELECT :
ENTER : OK
MENU
EXIT
:
CLOCK SET
DAY WED
23
MONTH
YEAR
TIME
1
2002
0:00
SELECT
:
SET
:
OK
: OK
EXIT : MENU
/ 0–9
AUTO TIME
ON
CLOCK SET
DAY WED
23
MONTH
YEAR
TIME
10
2002
11:30
SELECT
:
SET
:
OK
: OK
EXIT : MENU
/ 0–9
AUTO TIME
ON
CLOCK SET
DAY WED
23
MONTH
YEAR
TIME
10
2002
11:30
SELECT
:
SET
:
OK
: OK
EXIT : MENU
AUTO TIME
ON
VCR
2A73501AE(16-21) 4/17/02, 8:26 PM19
20
Preparation:
• Turn ON the TV and set to the video input mode.
• Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Then
press VCR to select the VCR mode. (The VCR indicator will light)
Example: Preset the SAT1 on program position 5.
1
Press SET UP MENU.
Press or to select
CHANNEL SETUP. Then press
OK.
2
Press or to select CH
TUNING. Then press OK.
3
DEC OFF will blink. Press OK.
DEC OFF does not blink any
more. SEARCH will appear.
Note:
If you wish to store the
PREMIERE manually, the
decoder must have been
connected as on the lower of p.11.
During DEC OFF is blinking, press
.
DEC ON will blink now.
Press OK.
4
Press (rising frequency) or
(falling frequency) once. The
search starts. It stops at each
broadcast automatically (" "
change to " 4 "). Press or
repeatedly until the SAT1
appears. Only in case of receiving
of the weak broadcast (drifting
picture), search dose not stop. If
you want to stop, press / or
/ .
CH TUNING
CHANNEL SETUP
CHANNEL MAPPING
SELECT :
ENTER
:OK
MENU
EXIT
:
TIMER REC SET
ATS (AUTO TUNING SYSTEM)
VCR EXTENSION
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : OK
MENU
EXIT
:
VCR SETUP
Manual TV station presetting
ATS stores the broadcast automatically.
However if you do the ATS under
unfavorable receiving conditions,
some broadcasts happen to be not
finded by ATS. For these broadcasts,
you can store also by manual.
Note:
Occasionally, the auto search might catch
a weak signal and stop. If the TV station
signal is weak, you shouldn't store this
station.
In that case restart the auto search using
or .
CH 1VPS
ARD
OK
OK
:
MENU
EXIT :
DEC OFF
SELECT :
CH 1
SEARCH :
/ F. TUNE :
MENU
EXIT
:
DEC OFF
2A73501AE(16-21) 4/17/02, 8:26 PM20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/