Polycom realpresence group convene Setup Manual

Polycom
Brand
Polycom
Model
realpresence group convene
Category
Security camera accessories
Type
Setup Manual
1
ENGLISH
www.polycom.com
© 2015, Polycom, Inc. All rights reserved. POLYCOM® and the names and marks as-
sociated with Polycom’s products are trademarks and/or service marks of Polycom,
Inc. and are registered and/or common law marks in the United States and various
other countries. No portion hereof may be reproduced or transmitted in any form or
by any means, for any purpose other than the recipient’s personal use, without the
express written permission of Polycom.
P/no. MFL69143011 (1503-REV00)
Set Up the Polycom® RealPresence® Group Convene™
Display AC/DC adapter 4 AC Power
adapters
Stand body
Stand base Screws (4 pcs)
(M4 X L10)
Cable cover Rear cover
HDMI cable DC-to-DC jumper
cable
2 Screws and
2 T-Nuts
Easy Setup Guide
*MFL69143011*
ENGLISH
2
ASSEMBLE THE STAND
1
2
3
Use the packing material from the
lower portion of the display as a
platform for assembly.
Do not stand the unit up until the
installation and cabling are complete.
INSTALL THE CAMERA
Unpack the RealPresence Group Series co-
dec and camera. Reserve the codec power
supply for future use.
Power supply
Only use the power supply
provided with the display
accessory.
Open the hinge on the camera and insert the hinge into the camera
bracket on the rear top of the display.
Gather the excess cable and secure with the cable ties.
3
ENGLISH
ASSEMBLE THE STAND
Use the packing material from the
lower portion of the display as a
platform for assembly.
Do not stand the unit up until the
installation and cabling are complete.
INSTALL THE CAMERA
Open the hinge on the camera and insert the hinge into the camera
bracket on the rear top of the display.
Gather the excess cable and secure with the cable ties.
Do not carry display by holding the base.
Do not carry the display upside down by just holding the
base. This may cause the display to fall off the stand and
could result in personal injury.
ENGLISH
4
CONNECT CABLES
Plug the DC-to-DC jumper between the
display and the codec.
Connect and route all cables through the
cable management channel.
Note: Generic cables
If you use generic cables
not certied by LG and
Polycom, the screen may
not display or there may
be image noise.
INSTALL THE CODEC
Install the RealPresence Group Series codec by inserting the T-nuts into
the keyholes on the back of the display.
Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer
to the RealPresence Group Series 500 Setup Sheet for details.
Route the LAN and DC power supply cables between the codec and dis-
play and then through the cable channel at the rear of the stand.
PREPARE THE CODEC
HDMI IN
DC-OUT
(12V 2.7 A)
DC-IN
(12V )
5
ENGLISH
CONNECT CABLES
INSTALL THE CODEC
Install the RealPresence Group Series codec by inserting the T-nuts into
the keyholes on the back of the display.
Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer
to the RealPresence Group Series 500 Setup Sheet for details.
Route the LAN and DC power supply cables between the codec and dis-
play and then through the cable channel at the rear of the stand.
PREPARE THE CODEC
HDMI IN
DC-OUT
(12V 2.7 A)
DC-IN
(12V )
HDMI IN
DC-OUT
(12V 2.7 A)
DC-IN
(12V )
HDMI IN
DC-OUT
(12V 2.7 A)
DC-IN
(12V )
ENGLISH
6
Stand Hinge
Cable cover
MANAGE THE CABLES
Arrange the cables so that they run below the stand hinge and then cover
them with the cable cover from the bottom up.
You can disassemble the cable cover by following the assembly instruc-
tions in reverse order.
INSTALL THE REAR COVER
Install the rear cover on the stand by tting the hooks on the cover into
the slots on the back of the display and sliding into place.
7
ENGLISH
MANAGE THE CABLES
Arrange the cables so that they run below the stand hinge and then cover
them with the cable cover from the bottom up.
You can disassemble the cable cover by following the assembly instruc-
tions in reverse order.
INSTALL THE REAR COVER
Install the rear cover on the stand by tting the hooks on the cover into
the slots on the back of the display and sliding into place.
ENGLISH
8
CONNECT THE HEADPHONES (OPTIONAL)
CONNECT POWER
DC Switch
(shipped
with codec)
Caution: Power on DC switch rst.
Power on the DC switch on the bottom of the product
before turning on the display.
Four AC power adapter cables are supplied with the display. Select the ap-
propriate AC power adapter cable for your geographic region. Connect the
cable to the power supply input. Connect the AC power cable, provided
with the RealPresence Group Series codec, to the AC power adapter cable.
9
ENGLISH
CONNECT THE HEADPHONES (OPTIONAL)
Bottom Center of
the Display
CONNECT POWER
Four AC power adapter cables are supplied with the display. Select the ap-
propriate AC power adapter cable for your geographic region. Connect the
cable to the power supply input. Connect the AC power cable, provided
with the RealPresence Group Series codec, to the AC power adapter cable.
ENGLISH
10
Power/Menu buttons
POWER ON THE SYSTEM
Power on the display. When the Automatic Standby message appears,
select Yes to disable Automatic Standby. Otherwise, the display will go
into Automatic Power Down after four hours and it will not wake up for
a video call without manually turning on the display. When the codec
nishes booting up, refer to the Polycom RealPresence Group Series
Administrator Guide for details on codec settings conguration and IP
connectivity.
ADJUST THE ANGLE
Automatic Standby
Automatic Standby is currently set at 4 hours.
Would you like to disable Automatic Standby?
Yes
No
Press "OK" button to select.
OK EXIT
11
ENGLISH
POWER ON THE SYSTEM
Power on the display. When the Automatic Standby message appears,
select Yes to disable Automatic Standby. Otherwise, the display will go
into Automatic Power Down after four hours and it will not wake up for
a video call without manually turning on the display. When the codec
nishes booting up, refer to the Polycom RealPresence Group Series
Administrator Guide for details on codec settings conguration and IP
connectivity.
ADJUST THE ANGLE
Front
Rear
-515
Warnings
-515
When you adjust the angle, do not hold the stand as shown on the
following illustration. You may injure your ngers.
Be careful not to touch or press the screen area when adjusting the
angle of the monitor.
-515
ENGLISH
12
LICENSES
The terms HDMI and HDMI High-
Definition Multimedia Interface,
and the HDMI logo are trademarks
or registered trademarks of HDMI
Licensing LLC in the United States
and other countries.
For more information about the components of the RealPresence Group
Series Media Center, refer to the documentation at
http://support.polycom.com/PolycomService/support/us/support/video/
group_series/group_packaged_solutions.html
.
LICENSES
The terms HDMI and HDMI High-
Definition Multimedia Interface,
and the HDMI logo are trademarks
or registered trademarks of HDMI
Licensing LLC in the United States
and other countries.
For more information about the components of the RealPresence Group
Series Media Center, refer to the documentation at
http://support.polycom.com/PolycomService/support/us/support/video/
group_series/group_packaged_solutions.html
.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Polycom realpresence group convene Setup Manual

Polycom
Brand
Polycom
Model
realpresence group convene
Category
Security camera accessories
Type
Setup Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents