DFI LR100-N16D/LR100-N16M/LR100-N16S User manual

LR100-N16/N18

SERIES

System Board

User’s Manual

A12540350

Copyright

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transfor-

mation/adaptation without the prior written permission from the copyright hold-

ers.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use

of this manual and specifically disclaims any express or implied warranties of

merchantability or fitness for any particular purpose. The user will assume the

entire risk of the use or the results of the use of this document. Further, the

manufacturer reserves the right to revise this publication and make changes to

its contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Changes after the publication’s first release will be based on the product’s revi-

sion. The website will always provide the most updated information.

Trademarks

All trademarks and registered trademarks of products appearing in this manual

are the properties of their respective holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

1

4

Introduction

Table of Contents

Copyright ...........................................................................................2

Trademarks ........................................................................................ 2

FCC and DOC Statement on Class B ..............................................3

About this Manual .............................................................................6

Warranty .......................................................................................... 6

Static Electricity Precautions ............................................................. 7

Safety Measures ................................................................................. 7

About the Package ............................................................................8

Before Using the System Board ........................................................ 8

Chapter 1 - Introduction ..................................................................9

Specifications ..................................................................................9

Features ...................................................................................... 12

Chapter 2 - Hardware Installation .................................................. 14

System Board Layout .................................................................... 14

System Memory ........................................................................... 15

Installing the DIM Module ......................................................... 16

Jumper Settings ............................................................................. 18

Clear CMOS Data ..................................................................... 18

PS/2 Power Select .................................................................... 19

USB Power Select ..................................................................... 20

Panel Power Select ................................................................... 21

CompactFlash Card Setting ....................................................... 22

COM 3 RS232/RS422/RS485 Select ............................................ 23

COM 2 RS232/Power Select ....................................................... 24

Power-on Select ....................................................................... 25

Rear Panel I/O Ports ..................................................................... 26

PS/2 Mouse and PS/2 Keyboard Ports ......................................... 27

COM (Serial) Ports ................................................................... 28

VGA Port ................................................................................. 30

RJ45 LAN Ports ........................................................................ 31

USB Ports................................................................................ 32

Audio ..................................................................................... 34

1

5

Introduction

I/O Connectors ............................................................................ 36

CD-in Internal Audio Connector ................................................. 36

S/PDIF Connector ..................................................................... 37

LVDS LCD Panel Connector and LCD/Inverter Power Connector ...... 38

Digital I/O Connector ................................................................ 40

SATA (Serial ATA) Connectors .................................................... 41

IDE Connector ......................................................................... 42

Cooling Fan Connectors ............................................................. 44

Chassis Instrusion Connector .................................................... 45

Power Connector ...................................................................... 46

Standby LED ........................................................................... 47

Front Panel Connectors ............................................................. 48

Expansion Slots ....................................................................... 49

Battery ................................................................................... 50

CompactFlash Socket ................................................................ 51

Chapter 3 - BIOS Setup .................................................................. 52

Overview ..............................................................................................................52

AMI BIOS Setup Utility ................................................................. 54

Main ....................................................................................... 54

Advanced ................................................................................ 55

PCIPnP .................................................................................... 69

Boot ....................................................................................... 70

Security .................................................................................. 73

Chipset ................................................................................... 77

Exit ........................................................................................ 82

Updating the BIOS ........................................................................ 85

Chapter 4 - Supported Software ................................................... 86

Appendix A - NLITE and AHCI Installation Guide ....................... 107

Appendix B - Watchdog Timer...................................................... 119

Appendix C - System Error Message ............................................ 122

Appendix D - Troubleshooting ...................................................... 124

1

6

Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual

in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board

Utility CD) will appear. Click “User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the

product, inability to use the product, unauthorized replacement or alteration

of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse,

improper installation, modification, accidents or unauthorized repair of the

product.

3. Unless otherwise instructed in this user’s manual, the user may not, under

any circumstances, attempt to perform service, adjustments or repairs on the

product, whether in or out of warranty. It must be returned to the purchase

point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial

damages to the product that has been modified or altered.

1

7

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components

or devices even before installing them in your system unit. Static electrical dis-

charge can damage computer components without causing any signs of physical

damage. You must take extra care in handling them to ensure against electro-

static build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag

until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the compo-

nents, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold

modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and

other components. Perform the upgrade instruction procedures described

at an ESD workstation only. If such a station is not available, you can

provide some ESD protection by wearing an antistatic wrist strap and

attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for instal-

lation or servicing. After installation or servicing, cover the system chassis

before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufac-

turer.

• Dispose of used batteries according to local ordinance.

1

8

Introduction

About the Package

The system board package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representative for as-

sistance.

 One system board

 One IDE cable

 One USB cable

 One Serial ATA cable

 One Serial ATA power cable

 One bracket mounted with a COM port

 One I/O shield

 One CD

 One QR (Quick Reference)

Optional Items

 USB port cable

 COM port cable

 Serial ATA data cable

 Serial ATA power cable

 I/O shield

 IDE cable

 Heat sink

The system board and accessories in the package may not come similar to the

information listed above. This may differ in accordance to the sales region or

models in which it was sold. For more information about the standard package in

your region, please contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the

following internal components.

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use which will nor-

mally include at least a keyboard, a mouse and a video display monitor.

1

9

Introduction

Processor

Southbridge

System Memory

Expansion Slots

Chapter 1 - Introduction

• Intel

®

Atom

TM

D510 (Dual Core) - LR100-N16D

Intel

®

Atom

TM

D410 (Single Core) - LR100-N16S

Intel

®

Atom

TM

N450 (Single Core) - LR100-N16M

Intel

®

Atom

TM

D525 (Dual Core) - LR100-N18D

Intel

®

Atom

TM

D425 (Single Core) - LR100-N18S

Intel

®

Atom

TM

N455 (Single Core) - LR100-N18M

• On die 2 x 512KB (LR100-N16D/N18D),

1 x 512KB (LR100-N16S/N16M/N18S/N18M);

8-way L2 cache

• C0 and C1 C-states - LR100-N16D/N16S/N18D/N18S

C0/C1(E)/C2(E)/C4(E) C-states - LR100-N16M/N18M

• 1.66GHz core frequency (LR100-N16D/N16S/N16M/N18M),

1.8GHz core frequency (LR100-N18D/N18S);

1.10V voltage

• IA 32-bit and Intel

®

64 architecture

• Micro-FCBGA8 packaging technologies

• Cooling option:

heat sink with cooling fan - LR100-N16D/N18D;

heat sink (fanless solution) - LR100-N16S/N16M/N18S/N18M

• Intel

®

ICH8M I/O Controller Hub

• Two 200-pin SODIMM sockets

• LR100-N16M/N18M - Supports DDR2 667MHz only

LR100-N16D/N16S/N18D/N18S - Supports DDR2

667/800MHz only

• LR100-N16M/N18M - Supports up to 2GB system memory

LR100-N16D/N16S/N18D/N18S - Supports up to 4GB sys-

tem memory

• Single channel memory interface

• Supports x16 devices

• 1 PCIE x1 slot

• 1 PCI slot

• 1 CompactFlash socket

Specifications

1

10

Introduction

Graphics

Audio

LAN

Serial ATA

Rear Panel I/O

Ports

Trusted Platform

Module-TPM

(optional)

LR100-N16D/N16S/N18D/N18S

• Intel

®

GMA 3150

- Contains a refresh of the 3rd generation graphics core

• 400MHz render clock frequency

• Display ports: LVDS and RGB

- Integrated single LVDS channel supports resolution up to

1366x768, 18bpp

- Analog RGB display output up to resolution 2048x1536 @ 60Hz

• DirectX 9 compliant Pixel Shader 2.0

LR100-N16M/N18M

• Intel

®

GMA 3150

- Contains a refresh of the 3rd generation graphics core

• 200MHz render clock frequency

• Display ports: LVDS and RGB

- Integrated single LVDS channel supports resolution up to

1280x800 or 1366x768

- Analog RGB display output up to resolution 1400x1050 @ 60Hz

• DirectX 9 compliant Pixel Shader 2.0

• Realtek ALC262 2-channel High Definition Audio

• High performance DACs with 100dB SNR

• ADCs with 90dB SNR

• Two stereo DACs support 24-bit PCM format for stereo au-

dio playback

• Three stereo ADCs support 20-bit PCM format for multiple

input streaming

• S/PDIF audio interface

• Intel 82567V Gigabit Ethernet Phy and Realtek RTL8111C

PCI Express Gigabit Ethernet controller

• Integrated 10/100/1000 transceiver

• Supports Full Duplex flow control (IEEE 802.3x)

• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

• Supports power down / link down power saving

• 3 Serial ATA ports compliant with SATA 1.0 specification

• SATA speed up to 3Gb/s (SATA 2.0)

• Mini-DIN-6 ports: PS/2 mouse port and PS/2 keyboard port

• 3 DB-9 RS232 serial ports

- Pins 1 and 9 of COM2 functions as RS232 signal or power

(selectable via jumper)

• 1 DB-15 VGA port

• 2 RJ45 LAN ports

• 4 USB 2.0/1.1 ports

• Mic-in, Line-in and Line-out

• Provides a Trusted PC for secure transactions

• Provides software license protection, enforcement and pass-

word protection

1

11

Introduction

I/O Connectors

BIOS

Energy Efficient

Design

Damage Free

Intelligence

Power

Consumption

Temperature

Humidity

Dimensions

Certification

• 3 connectors for 6 external USB 2.0/1.1 ports

• 1 connector for an external RS232/422/485 serial port

• 1 LVDS LCD panel connector

• 1 LCD/inverter power connector

• 1 8-bit DIO connector

• 1 DIO power connector

• 1 front audio connector for line-out and mic-in jacks

• 1 CD-in connector

• 1 S/PDIF connector

• 3 Serial ATA connectors

• 1 40-pin IDE connector

• 1 24-pin ATX power connector

• 1 front panel connector

• 1 chassis intrusion connector

• 2 fan connectors

• AMI BIOS

• SPI BIOS

• ACPI 1.0a specification

• System Power Management

• Wake-On-Events include:

- Wake-On-USB Keyboard/Mouse

- Wake-On-LAN

- Wake-On-Ring

- RTC timer to power-on the system

• AC power failure recovery

• Monitors CPU/system temperature and overheat alarm

• Monitors 5V/1.05V/1.8V/12V/3VSB/VBAT/VCORE voltages

and failure alarm

• Monitors system fan speed and failure alarm

• Read back capability that displays temperature, voltage and

fan speed

• Watchdog timer function

• 12.71 W with D410 at 1.66GHz and 1x 1GB DDR2 SODIMM

• 0

o

C to 60

o

C

• 10% to 90%

• Mini-ITX form factor

- 170mm (6.7”) x 170mm (6.7”)

• Heat sink

LR100-N16M/N16S/N18M/N18S

- 68mm x 50mm x 30mm

• Heat sink with fan

LR100-N16D/N18D

- 68mm x 50mm x 40mm

• CE, FCC Class B, UL, RoHS

1

12

Introduction

Features

Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the sys-

tem at the set time interval. If the system hangs or fails to function, it will reset

at the set time interval so that your system will continue to operate.

CompactFlash

The system board is equipped with the CompactFlash

TM

socket for inserting a

CompactFlash

TM

card. CompactFlash

TM

card is a small removable mass storage

device designed with flash technology - a non-volatile storage solution that does

not require a battery to retain data indefinitely. The CompactFlash

TM

technology

is widely used in products such as portable and desktop computers, digital cam-

eras, handheld data collection scanners, PDAs, Pocket PCs, handy terminals and

personal communicators.

DDR2

DDR2 is a higher performance DDR technology whose data transfer rate delivers

bandwidth of 4.3 GB per second and beyond. That is twice the speed of the con-

ventional DDR without increasing its power consumption. DDR2 SDRAM modules

work at 1.8V supply compared to 2.6V memory voltage for DDR modules. DDR2

also incorporates new innovations such as the On-Die Termination (ODT) as well

as larger 4-bit pre-fetch against DDR which fetches 2 bits per clock cycle.

Graphics

The Intel

®

chipset features sophisticated graphics for large display applications.

Graphics interfaces such as VGA and LVDS support multiple graphics display op-

tions.

PCI Express

PCI Express is a high bandwidth I/O infrastructure that possesses the ability to

scale speeds by forming multiple lanes. The x1 PCI Express lane supports trans-

fer rate of 2.5 Gigabytes (250MBbps) per second which is nearly 4 times faster

than the traditional PCI.

S/PDIF

S/PDIF is a standard audio file transfer format that transfers digital audio sig-

nals to a device without having to be converted first to an analog format. This

prevents the quality of the audio signal from degrading whenever it is converted

to analog. S/PDIF is usually found on digital audio equipment such as a DAT

machine or audio processing device. The S/PDIF connector on the system board

sends surround sound and 3D audio signal outputs to amplifiers and speakers

and to digital recording devices like CD recorders.

1

13

Introduction

Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specification.

With speed of up to 3GB/s, it improves hard drive performance faster than the

standard parallel ATA whose data transfer rate is 100MB/s.

Gigabit LAN

The Intel 82567V and Realtek RTL8111C PCI Express Gigabit controllers support

up to 1Gbps data transmission.

USB

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 supports 12Mb/

second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing a

marked improvement in device transfer speeds between your computer and a

wide range of simultaneously accessible external Plug and Play peripherals.

14

2

Hardware Installation

System Board Layout

Chapter 2 - Hardware Installation

DDR2_2 SODIMM

DDR2_1 SODIMM

Intel

Atom

Intel

ICH8M

PS/2 Mouse

PS/2 KB

COM 2

COM 1

COM 4

VGA

LAN 1

USB 1

USB 0

LAN 2

USB 3

USB 2

Mic-in

Line-in

Line-out

1

PS/2 power

select (J )P1

1

2

5

6

COM2 RS232/Power

select (J6)

LVDS LCD

panel

40 39

2

1

LCD/Inverter power

1

2

5

6

Panel power

select ( )J5

1

USB 0-3 power

select (J )P2

1

CPU fan

1

CD-in

1

Front audio

2

S/PDIF

1

USB 4-7 power

select (J )P3

USB 8-9 power

select (J )P4

1

2

1

2

1

2

9

10

9

10

9

10

USB 4-5

USB 6-7

USB 8-9

Realtek

ALC262

Standby LED

PCI

PCIE

SPI Flash

BIOS

Clear CMOS

(JP5)

1

CF card setting

(JP6)

Battery

12

3940

CompactFlash

1

SATA 2

1

SATA 1

1

SATA 0

1

2

9

COM 3

1 2

11

12

PWR LED

ATX SW

HD LED

Front

panel

F81216AD

1

DIO

DIO power

1

Chassis

intrusion

1

Power-on

select ( )JP8

1

2

5

6

COM3 RS232/422/485

select ( )JP9

1

13

12

24

ATX power

1

System fan

IDE

RESET

15

2

Hardware Installation

Important:

When the Standby LED lit red, it indicates that there is power on the

system board. Power-off the PC then unplug the power cord prior to

installing any devices. Failure to do so will cause severe damage to the

motherboard and components.

System Memory

Important:

Electrostatic discharge (ESD) can damage your system board, processor,

disk drives, add-in boards, and other components. Perform the upgrade

instruction procedures described at an ESD workstation only. If such a

station is not available, you can provide some ESD protection by wearing

an antistatic wrist strap and attaching it to a metal part of the system

chassis. If a wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requiring ESD pro-

tection.

DDR2-2

Standby LED

The system board supports two DDR2 SODIMM sockets.

DDR2-1

16

2

Hardware Installation

Installing the DIM Module

Note:

The system board used in the following illustrations may not resemble

the actual one. These illustrations are for reference only.

1. Make sure the PC and all other peripheral devices connected to it has been

powered down.

2. Disconnect all power cords and cables.

3. Locate the SODIMM socket on the system board.

4. Note the key on the socket. The key ensures the module can be plugged into

the socket in only one direction.

17

2

Hardware Installation

6. Push down the module until the clips at each end of the socket lock into

position. You will hear a distinctive “click”, indicating the module is correctly

locked into position.

Clip

5. Grasping the module by its edges, align the module into the socket at an ap-

proximately 30 degrees angle. Apply rm even pressure to each end of the

module until it slips down into the socket. The contact ngers on the edge of

the module will almost completely disappear inside the socket.

18

2

Hardware Installation

Jumper Settings

Clear CMOS Data

If you encounter the following,

a) CMOS data becomes corrupted.

b) You forgot the supervisor or user password.

you can recongure the system with the default values stored in the ROM BIOS.

To load the default values stored in the ROM BIOS, please follow the steps below.

1. Power-off the system and unplug the power cord.

2. Set JP5 pins 2 and 3 to On. Wait for a few seconds and set JP5 back to its

default setting, pins 1 and 2 On.

3. Now plug the power cord and power-on the system.

JP5

2-3 On:

Clear CMOS Data

1-2 On: Normal

(default)

3

1

2

3

1

2

19

2

Hardware Installation

JP1 is used to select the power of the PS/2 keyboard/mouse port. Selecting

+5V_standby will allow you to use the PS/2 keyboard or PS/2 mouse to wake up

the system.

PS/2 Power Select

JP1

3

1

2

3

1

2

2-3 On:

+5V_standby

1-2 On: +5V

(default)

20

2

Hardware Installation

JP2 (for USB 0-3), JP3 (for USB 4-7) and JP4 (for USB 8-9) are used to select

the power of the USB ports. Selecting +5V_standby will allow you to use a USB

device to wake up the system.

BIOS Setting

“USB Device Wakeup From S3” in the Advanced menu (“ACPI Conguration” sub-

menu) of the BIOS must be set to Enabled. Refer to chapter 3 for more informa-

tion.

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB

ports, the +5V_standby power source of your power supply must sup-

port ≥1.5A. For 3 or more USB ports, the +5V_standby power source of

your power supply must support ≥2A.

USB Power Select

USB 0-3 power

select (JP2)

3

1

2

3

1

2

2-3 On:

+5V_standby

1-2 On: +5V

(default)

USB 4-7 power

select (JP3)

USB 8-9 power

select (JP4)

Page is loading ...

DFI LR100-N16D/LR100-N16M/LR100-N16S User manual

This manual is also suitable for

DFI LR100-N16D/LR100-N16M/LR100-N16S User manual

Related papers

Other documents