H3C S3100-8C-EPON-EI Quick start guide

H3C S3100 Series Ethernet Switches

Quick Start (For Japan)

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08018X-20080110-C-1.04

Ltd. and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF,

NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,

Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus,

N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners.

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of

any kind, express or implied.

To obtain the latest information, please access:

http://www.h3c.com

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S3100 Series Ethernet

Switches documentation set includes the following:

Manual Content

H3C S3100 Series Ethernet

Switches Operation Manual

It is used for assisting the users

in data configurations and

typical applications.

H3C S3100 Series Ethernet

Switches Command Manual

It is used for assisting the users

in using various commands.

H3C S3100 Series Ethernet

Switches Installation Manual

(For Japan)

It is used for assisting the users

in switch installation, booting up,

hardware and software

maintenance.

Organization

H3C S3100 Series Ethernet Switches Quick Start (For Japan) is

organized as follows:

Chapter Contents

1 Product Overview

Introduces the characteristics and

technical specifications of S3100

Series Ethernet Switches.

2 Installation Preparation

Introduces the installation

preparation and precaution of

S3100 Series Ethernet Switches.

Chapter Contents

3 Installation

Introduces the procedures to install

an S3100 Series Ethernet Switch,

including the setup of the

mainframe, cards and cables.

4 Lightning Protection of the

Switch

Introduces lightning protection of

S3100 Series Ethernet Switches.

Conventions

The manual uses the following conventions:

I.

GUI conventions

Convention Description

< >

Button names are inside angle brackets.

For example, click <OK>.

[ ]

Window names, menu items, data table

and field names are inside square

brackets. For example, pop up the [New

User] window.

/

Multi-level menus are separated by forward

slashes. For example, [File/Create/Folder].

II.

Symbols

Convention Description

Warning

Means reader be extremely careful.

Improper operation may cause bodily

injury.

Convention Description

Caution

Means reader be careful. Improper

operation may cause data loss or damage

to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements

on environmental protection. For the proper storage, use and disposal

of this product, national laws and regulations must be observed.

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Table of Contents

i

Table of Contents

Chapter 1 Product Overview ........................................................1-1

1.1 Overview ............................................................................1-1

1.1.1 S3100-SI Series Ethernet Switches ........................1-2

1.1.2 S3100-EI Series Ethernet Switches ........................1-3

1.2 Introduction to Front Panel Power LEDs ...........................1-5

1.3 Technical Specifications ....................................................1-6

1.3.1 S3100-SI Series Ethernet Switch ............................1-6

1.3.2 S3100-EI Series Ethernet Switch ..........................1-10

1.4 SFP Modules Supported by S3100-EI Ethernet Switches1-16

1.5 ONU Modules...................................................................1-17

Chapter 2 Installation Preparation...............................................2-1

2.1 Precautions ........................................................................2-1

2.2 Requirements on Environment ..........................................2-1

2.2.1 Temperature/Humidity Requirements .....................2-2

2.2.2 Cleanness Requirements ........................................2-3

2.2.3 Anti-interference Requirements...............................2-4

2.2.4 Laser Usage Security ..............................................2-5

2.3 Installation Tools ................................................................2-5

Chapter 3 Installation....................................................................3-1

3.1 Installing a Switch ..............................................................3-1

3.1.1 Cabinet Mounting ....................................................3-1

3.1.2 Desk Mounting.......................................................3-16

3.1.3 Wall Mounting........................................................3-16

3.1.4 Magnet Mounting...................................................3-20

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Table of Contents

ii

3.2 Installing an Expansion Interface Module ........................3-23

3.3 Connection of Power Cord and Grounding Cable ...........3-24

3.3.1 Connecting AC Power Cord ..................................3-24

3.3.2 Connecting DC Power Cable ................................3-27

3.3.3 Connecting Grounding Cable ................................3-33

3.4 Connecting Optical Fiber .................................................3-38

3.5 Connection of Console Cable ..........................................3-39

3.5.1 Console Cable .......................................................3-39

3.5.2 Connecting Console Cable....................................3-40

3.6 Installation Verification .....................................................3-41

Chapter 4 Lightning Protection of the Switch ............................4-1

4.1 Installation of Lightning Arrester for AC Power (Socket Strip

with Lightning Protection).........................................................

4-1

4.2 Installation of Lightning Arrester for Network Port .............4-4

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-1

Chapter 1 Product Overview

1.1 Overview

H3C S3100 Series Ethernet Switches are high-performance,

high-density, easy-to-install, NMS-manageable intelligent Ethernet

switches which support wire-speed Layer 2 switching.

Table 1-1 lists the models of H3C S3100 Series Ethernet

Switches.

Table 1-1 Models of H3C S3100 Series Ethernet Switches

Name Subseries Model

S3100-C-SI

z S3100-8C-SI

z S3100-16C-SI

z S3100-26C-SI

S3100-

SI

S3100-T-SI

z S3100-8T-SI

z S3100-16T-SI

z S3100-26T-SI

S3100-TP-EI-W

z S3100-8TP-EI-W

z S3100-16TP-EI-W

z S3100-26TP-EI-W

S3100-TP-PWR

-EI

z S3100-8TP-PWR-EI

z S3100-16TP-PWR-EI

z S3100-26TP-PWR-EI

H3C

S3100

Series

Ethernet

Switches

S3100-

EI

S3100-C-EPON

-EI

z S3100-8C-EPON-EI

z S3100-16C-EPON-EI

z S3100-26C-EPON-EI

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-2

1.1.1 S3100-SI Series Ethernet Switches

Currently, S3100-SI Series Ethernet switches include S3100-T-SI

and S3100-C-SI, as listed in

Table 1-2 and Table 1-3.

Table 1-2 H3C S3100-T-SI Series Ethernet switches

Model

Power

supply

Number

of

10/100M

electrical

ports

Number

of gigabit

uplink

ports

Number

of

console

ports

S3100-26T-SI 24

2 Ethernet

ports

S3100-16T-SI 16

S3100-8T-SI

AC

8

1 Ethernet

port

1

Table 1-3 H3C S3100-C-SI Series Ethernet Switches

Model

Power

supply

Number of

10/100M

electrical

ports

Number of

expansion

slots

Number of

console

ports

S3100-26

C-SI

24 2

S3100-16

C-SI

16 2

S3100-8C

-SI

AC input for

AC-powere

d switch.

DC input for

DC-powere

d switch

8 1

1

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-3

 Note:

For details about each model, refer to H3C S3100 Series Ethernet

Switches Installation Manual (For Japan).

1.1.2 S3100-EI Series Ethernet Switches

Currently, the H3C S3100-EI Series Ethernet Switches include

the S3100-TP-EI-W, the S3100-TP-PWR-EI and the

S3100-C-EPON-EI, as listed in

Table 1-4 and Table 1-5.

Table 1-4 Models of H3C S3100-TP-EI-W and S3100-TP-PWR-

EI Series Ethernet switches

Model

Power

supply

Number of

10/100M

electrical

ports

1000M

uplink

ports

Number of

console

ports

S3100-26T

P-EI-W

AC input or

12V-RPS

DC input

24

2 Combo

ports

1

S3100-16T

P-EI-W

16

2 Combo

ports

1

S3100-8T

P-EI-W

AC input

8

1 Combo

port

1

H3C

S3100-26T

P- PWR-EI

AC input or

52V-RPS

DC input

24

2 Combo

ports

1

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-4

Model

Power

supply

Number of

10/100M

electrical

ports

1000M

uplink

ports

Number of

console

ports

H3C

S3100-16T

P- PWR-EI

16

2 Combo

ports

1

H3C

S3100-8T

P- PWR-EI

AC input

8

1 Combo

port

1

Table 1-5 Models of the H3C S3100-C-EPON-EI Series Ethernet

Switches

Model

Power

input

Number

of 10/100

Mbps

electrica

l ports

Number

of 1000

Mbps

uplink

PON

ports

Number

of

expansi

on slots

Numb

er of

consol

e ports

S3100-26

C-EPON-

EI

24 1 1

S3100-16

C-EPON-

EI

16 1 Disabled

S3100-8C

-EPON-EI

AC

input

8 1 —

1

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-5

 Note:

For details about each model, refer to H3C S3100 Series Ethernet

Switches Installation Manual (For Japan).

1.2 Introduction to Front Panel Power LEDs

Table 1-6 Description of the power LED on S3100 series

LED

Mark on the

panel

Status Description

ON

The switch is

powered on.

Power LED PWR

OFF

The switch is

powered off.

ON

DC input is

normal.

RPS DC

power LED

RPS

OFF

There is no

DC input.

 Note:

Only S3100-26TP-EI-W AC-powered Ethernet switches have an RPS

DC power LED.

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-6

1.3 Technical Specifications

1.3.1 S3100-SI Series Ethernet Switch

I. S3100-T-SI Series

Table 1-7 Technical specifications for S3100-T-SI Series

Ethernet switches

Model S3100-26T-SI S3100-16T-SI S3100-8T-SI

Physical

dimensions (H

x W x D)

42 x 436 x 240

mm (1.65 x

17.2 x 9.4 in)

42 x 436 x 200

mm (1.65 x

17.2 x 7.9 in)

42 x 326 x 200

mm (1.65 x

12.8 x 7.9 in)

Weight ≤ 3.2 kg (7.1 lb)

Number of

fixed ports

24 x

auto-sensing

10/100Base-

TX Ethernet

port

2 x

10/100/1000

Base-T

Ethernet port

16 x

auto-sensing

10/100Base-

TX Ethernet

port

1 x

10/100/1000

Base-T

Ethernet port

8 x

auto-sensing

10/100Base-

TX Ethernet

port

1 x

10/100/1000

Base-T

Ethernet port

Number of

management

port

1 x console port

Power system

Only AC input is supported.

Rated voltage range: 100 VAC to 240 VAC, 50 Hz

/60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz to

63 Hz

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-7

Model S3100-26T-SI S3100-16T-SI S3100-8T-SI

PoE (as

powered

device)

Not supported Not supported Not supported

System power

consumption

(full load)

20 W 12 W 10 W

Fan None None None

Operating

temperature

0°C to 45°C (30°F to 113°F)

Relative

humidity (non-

condensing)

10% to 90%

II. S3100-C-SI Series

Table 1-8 Technical specifications for S3100-C-SI Series

Ethernet switches

Model S3100-26C-SI S3100-16C-SI S3100-8C-SI

Physical

dimensions (H

x W x D)

42 x 436 x 240

mm (1.65 x

17.2 x 9.4 in)

42 x 436 x 200

mm (1.65 x

17.2 x 7.9 in)

42 x 326 x 200

mm (165 x

12.8 x 7.9 in)

Weight ≤ 3.2 kg (7.1 lb)

Number of

fixed ports

24 x

auto-sensing

10/100Base-

TX Ethernet

port

16 x

auto-sensing

10/100Base-

TX Ethernet

port

8 x

auto-sensing

10/100Base-

TX Ethernet

port

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-8

Model S3100-26C-SI S3100-16C-SI S3100-8C-SI

Number of

expansion

slots

2 2 1

Number of

management

port

1 x Console port

Supported

expansion

interface

module type

10/100/1000BASE-T interface module with max

transmission distance of 100 m (328.1 feet)

100BASE-SX (SC, 2 km (1.2 mi))

100BASE-LX (SC, 15 km (9.3 mi))

100BASE-LH40 (SC, 40 km (24.9 mi))

1000BASE-SX (SC, 0.5 km (0.3 mi))

1000BASE-LX (SC, 10 km (6.2 mi))

1000BASE-LH40 (LC, 40 km (24.9 mi))

1000BASE-LH70 (LC, 70 km (43.5 mi))

1000BASE-STACK (not supported by

S3100-8C-SI)

100BASE-TX PD (powered device) interface

module (only supported by S3100-16C-SI

DC-powered switch and S3100-8C-SI

DC-powered switch)

1000BASE-PX10 (SC, 10 km (6.2 mi))

1000BASE-PX20 (SC, 20 km (12.4 mi))

100Base-LX-SM1310-BIDI (SC, 15 km (9.3 mi))

100Base-LX-SM1550-BIDI (SC, 15 km (9.3 mi))

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-9

Model S3100-26C-SI S3100-16C-SI S3100-8C-SI

Power system

Both DC-powered switch and AC-powered switch

are available to each model. The AC-powered

switch supports only AC input. and the

DC-powered switch supports only DC input.

AC input:

z Rated voltage range: 100 VAC to 240 VAC, 50

Hz /60Hz

z Input voltage range: 90 VAC to 264 VAC, 47

Hz to 63 Hz

DC input:

z Rated voltage range: –48 VDC to –60 VDC

z Input voltage range: –36 VDC to –72 VDC

PoE (as

powered

device)

Not supported

Supported by DC-powered

switch

System power

consumption

(full load)

20 W 12 W 10 W

Fan None None None

Operating

temperature

0°C to 45°C (30°F to 113°F)

Relative

humidity (non-

condensing)

10% to 90%

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-10

 Note:

z Only S3100-16C-SI DC-powered switch or S3100-8C-SI

DC-powered switch supports 100BASE-TX PD interface module.

Notice that S3100-16C-SI DC-powered switch can accommodate

only one PD interface module.

z The PoE configuration is on the remote power source device, on

the powered device (S3100-16C-SI DC-powered switch or

S3100-8C-SI DC-powered switch), you only need to insert the

cable into the interface of 100BASE-TX PD.

z BIDI interface card must used in couple, i.e., if the local end uses

100Base-LX-SM1310-BIDI, the remote end need to use

100Base-LX-SM1550-BIDI.

z An S3100-16C-SI or S3100-26C-SI switch can accommodate only

one ONU card (1000Base-PX10/20). For details about ONU

modules, refer to section

1.5 “ONU Modules”.

1.3.2 S3100-EI Series Ethernet Switch

I. S3100-TP-EI-W Series

Table 1-9 Technical specifications for S3100-TP-EI-W Series

Ethernet switches

Model

S3100-26TP-

EI-W

S3100-16TP-

EI-W

S3100-8TP-EI

-W

Physical

dimensions (H

x W x D)

43.6 x 440 x

260 mm (1.7 x

17.2 x 10.2 in)

43.6 x 300 x

220 mm (1.7 x

11.8 x 8.7 in)

43.6 x 230 x

200 mm (1.7 x

9.1 x 7.9 in)

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-11

Model

S3100-26TP-

EI-W

S3100-16TP-

EI-W

S3100-8TP-EI

-W

Weight <3.5 kg (7.7 lb) <2.5 kg (5.5 lb) <1.8 kg (4 lb)

Number of

fixed ports

24 x

auto-sensing

10/100BASE-

TX Ethernet

port

2 x 1000M

Combo port

16 x

auto-sensing

10/100BASE-

TX Ethernet

port

2 x 1000M

Combo port

8 x

auto-sensing

10/100BASE-

TX Ethernet

port

1 x 1000M

Combo port

Number of

management

port

1 x console port

Power system

S3100-16TP-EI-W/S3100-8TP-EI-W Ethernet

switches support only AC input.

S3100-26TP-EI-W AC-powered switches support

AC input and RPS DC input.

AC input:

z Rated voltage range: 100 VAC to 240 VAC, 50

Hz /60 Hz

z Input voltage range: 90 VAC to 264 VAC, 47

Hz to 63Hz

RPS DC input:

z Input voltage range: 10.8 VDC to 13.2 VDC

PoE (as

powered

device)

Not supported Not supported Not supported

System power

consumption

(full load)

22 W 17 W 14 W

Fan None None None

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-12

Model

S3100-26TP-

EI-W

S3100-16TP-

EI-W

S3100-8TP-EI

-W

Operating

temperature

0°C to 45°C (30°F to 113°F)

Relative

humidity (non-

condensing)

10% to 90%

Caution:

Only the recommended 12V-RPS DC power supply can be used for

S3100-26TP-EI Ethernet switches.

II. S3100-TP-PWR-EI Series

Table 1-10 Technical specifications for S3100-TP-PWR-EI

Ethernet switches

Model

S3100-26TP-

PWR-EI

S3100-16TP-

PWR-EI

S3100-8TP-

PWR-EI

Physical

dimensions (H x

W x D)

43.6 x 440 x

420 mm (1.7 x

17.2 x 10.2 in)

43.6 x 300 x

260 mm (11.8

x 8.7 x 1.7 in)

43.6 x 300 x

220 mm (1.7 x

9.1 x 7.9 in)

Weight

<6.5 kg (14.3

lb)

<3.5 kg (7.7

lb)

<3.0 kg (6.6

lb)

Quick Start (For Japan)

H3C S3100 Series Ethernet Switches

Chapter 1 Product Overvie

w

1-13

Model

S3100-26TP-

PWR-EI

S3100-16TP-

PWR-EI

S3100-8TP-

PWR-EI

Number of fixed

ports

24 x

10/100BASE-

TX

auto-sensing

Ethernet port

2 x 1000M

Combo port

16 x

10/100BASE-

TX

auto-sensing

Ethernet port

2 x 1000M

Combo port

8 x

10/100BASE-

TX

auto-sensing

Ethernet port

1 x 1000M

Combo port

Number of

management

ports

1 x Console port

Power system

S3100-26TP-PWR-EI Ethernet switches

supports AC input and RPS DC input.

S3100-16TP-PWR-EI/S3100-8TP-PWR-EI

Ethernet switches support only AC input.

AC input:

z Rated voltage range: 100 VAC to 240 VAC,

50 Hz /60 Hz

z Input voltage range: 90 VAC to 264 VAC, 47

Hz to 63 Hz

RPS DC input:

z Input voltage range: –52 VDC to –56 VDC

System

power

consum

ption

(full

load)

AC input:

465 W

DC input:

400 W

160 W 95 W

All

ports

serve

as

PoE

ports

PoE

power

maximu

m

15.4 W x 24 15.4 W x 8 15.4 W x 4

Page is loading ...

H3C S3100-8C-EPON-EI Quick start guide

H3C S3100-8C-EPON-EI Quick start guide

Related papers

Other documents