PLIANT TECHNOLOGIES MicroCom 2400M Wireless Intercom User guide

Brand
PLIANT TECHNOLOGIES
Model
MicroCom 2400M Wireless Intercom
Type
User guide
For more information visit
www.plianttechnologies.com
QUICK START GUIDE
CUSTOMER SUPPORT
Pliant Technologies oers technical support via phone and
email from 07:00 to 19:00 Central Time (UTC−06:00), Monday
through Friday.
+1.844.475.4268 or +1.334.321.1160
customer[email protected]
You may also visit our website (www.plianttechnologies.com)
for live chat help. (Live chat available 08:00 to 17:00 Central
Time (UTC−06:00), Monday–Friday.)
Additional Documentation
This is a quick start guide. For additional
details on menu settings, device specifications,
and product warranty, view the full MicroCom
Operating Manual on our website. (Scan this
QR code with your mobile device to navigate
there quickly.)
COPYRIGHT © 2022 Pliant Technologies, LLC. All rights reserved. Pliant®, MicroCom®,
and the Pliant “P” logo are registered trademarks of Pliant Technologies, LLC. Any and
all other trademark references within this document are property of their respective
owners.
Document Reference: D0000522_C
IN THIS BOX
WHAT’S INCLUDED WITH MICROCOM 2400M?
• Holster
• Lanyard
• USB Charging Cable
ACCESSORIES
OPTIONAL ACCESSORIES
• PAC-USB6-CHG: MicroCom 6-Port USB Charger
• PAC-MC-5CASE: IP67-rated Hard Travel Case
• PAC-MC-SFTCASE: MicroCom Soft Travel Case
• Selection of compatible headsets (see Pliant website for
more details)
Talk/State LED
Charging LED
Power Button
Talk Button
Headset
Connection
USB Charger
Connection
Volume +/–
Buttons Mode Button
LCD Screen
Antenna
SETUP
1. Connect a headset to the beltpack.
2. Power on. Press and hold the Power button for three (3)
seconds, until the screen turns on.
3. Select a Group. Press and hold the Mode button for 3
seconds until the “GRP” symbol is blinking on the LCD.
Then, use the Volume +/− buttons
to select a group number from
0–51. Short-press Mode to save
your selection and proceed to ID
setting.
IMPORTANT: Beltpacks must have
the same group number to communicate.
4. Select an ID. When “ID” begins to blink on the LCD, use
the Volume +/− buttons to select an ID number. Press and
hold Mode to save your selection and exit the menu.
a. Pack IDs range from 00–05.
b. One pack must always use the
“00” ID and serve as the master
pack for proper system
function. “MR” designates the
master pack on its LCD.
c. Listen-only packs must use the “05” ID. You may
duplicate ID “05” on multiple beltpacks if setting up
listen-only users. (See the MicroCom 2400M Manual for
more information about that process.)
d.
Shared Talk beltpacks must use the “Sh” ID. You may
duplicate ID “Sh” on multiple beltpacks if setting up
shared users. However, the “Sh” ID cannot be used at
the same time as the last full-duplex ID (“04”).
Figure 1: Group Edit Screen
Figure 2: ID Edit Screen (Master ID)
OPERATION
• Talk - Use the Talk button to enable or disable talk for the
device. This button changes with a single, short press. “TK”
appears on the LCD when enabled.
»For full-duplex users, use a single, short press to toggle
talk on and o.
»For Shared Talk users (“Sh”), press and hold while talking
to enable it for the device. (Only one Shared Talk user can
talk at a time.)
• Volume Up and Down - Use the + and − buttons to control
the volume. “VOL” and a numerical value from 00–09
appear on the LCD when volume is adjusted.
Multiple MicroCom Systems
Each separate MicroCom system should use the same Group
for all beltpacks in that system. Pliant recommends that
systems operating in proximity to one another set their Groups
to be at least 10 values apart. For example, if one system is
using Group 03, another system nearby should use Group 13.
Battery
• Battery life: Approx. 7.5 hours
• Charge time from empty: Approx. 3.5 hours
• Charging LED on beltpack will illuminate red while charging
and will turn o when charging complete.
• Beltpack may be used while charging, but doing so may
lengthen charge time.
Menu Options
To access the menu, press and hold the Mode button for 3
seconds. Once you have finished your changes, press and
hold Mode to save your selection and exit the menu.
Recommended Settings by Headset
Menu Setting Default Options Description
Side Tone S3 S0 O
S1–S5 Levels 1–5
Receiving Mode PO
PO Rx & Tx Mode
PF Rx-Only Mode
(Listen-Only)
Mic Sensitivity Level C1 C1–C5 Levels 1–5
Audio Output Level UH UL Low
UH High
Headset Type
Recommended Setting
Mic Sensitivity Audio Output
Headset with boom mic C1 UH
Headset with lavalier mic C3 UH
  • Page 1 1
  • Page 2 2

PLIANT TECHNOLOGIES MicroCom 2400M Wireless Intercom User guide

Brand
PLIANT TECHNOLOGIES
Model
MicroCom 2400M Wireless Intercom
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents