CAUTION!
Before commencing, disconnect the
device from the mains. There are parts that
carry mains voltage behind the cover. Never
leave unsupervised when it is open. (Prevent
non specialists and especially children from
gaining access to it.)
Never remove this product from the
electrical baseplate. Disconnect from mains
supply in the event of any damage to any
buttons. Do not use sharp tools to push any
button.
R37 - 3 Zone Programmer Operating Instructions
Page 1 of 2
Press the or buttons to adjust the P1 ON time.
Press the or buttons to adjust the P1 OFF time.
Repeat this process to adjust the ON & OFF times for P2 & P3.
Press and repeat the above process to adjust for Zone 2.
Press and repeat the above process to adjust for Zone 3.
When completed, move the selector switch to the RUN position.
1. Factory default settings
6. Adjusting the program settings
2. Factory program settings
Program: 5/2D
Backlight: On
Keypad: Unlocked
Frost Protection: O
3. Resetting the programmer Press
Press
This 3 zone programmer is designed to
provide ON/OFF control for 3 zones, with
the value added application of in built
frost protection and keypad lock.
It is necessary to press the RESET button prior to initial programming.
This button is located behind the cover on the front of the unit.
AUTO The programmer operates 3 ‘ON/OFF’ periods per day.
ALL DAY The programmer operates 1’ON/OFF’ period per day.
This operates from the rst ON time to the third OFF time.
ON The programmer is permanently on. **ON**
OFF The programmer is permanently o. **OFF**
Lower the cover on the front of the unit. By pressing the button,
you can change between AUTO / ALL DAY / ON / OFF for Zone 1.
Repeat this process for Zone 2 by pressing the button and for
Zone 3 by pressing the button.
5. ON/OFF period selection
There are 4 modes available on this programmer for users to choose for their
individual application.
3
3
4. Setting the date and time
Press
Press
Press
Press
Press
Press
Lower the cover on the front of the unit.
Move the selector switch to the CLOCK SET position.
Press the or buttons to select the day.
Press the or buttons to select the month.
Press the or buttons to select the year.
Press the or buttons to select the hour.
Press the or buttons to select the minute.
Press the or buttons to select 5/2D, 7D or 24H
The date, time and function are now set. Move the selector switch to the
RUN position to run the program, or to the PROG SET position to change
the program setting.
RUN
CLOCK
SET
PROG
SET
Lower the cover on the front of the unit.
Move the selector switch to the PROG SET position.
You can now program Zone 1.
Copy function may only be used if the programmer is in the 7d mode.
Lower the cover on the front of the programmer.
Move the selector switch to the PROG SET position.
Set the ON & OFF times for the day of the week you wish to copy from.
Press the button for 2 secs. The next day of the week will begin to ash.
Press the button to copy the ON & OFF to this day.
Press the button to skip a day.
ON & OFF times can be copied to multiple days by using the button.
Press the button when copying has been completed.
When completed, move the selector switch to the RUN position.
RUN
CLOCK
SET
PROG
SET
Holiday
COPY
7. Copy function
20221107_R37_OpIns_PK
EPH Controls Ireland
technical@ephcontrols.com www.ephcontrols.com
EPH Controls UK
technical@ephcontrols.co.uk www.ephcontrols.co.uk
Important: Keep this document
RUN
CLOCK
SET
PROG
SET
Mon-Fri
Sat-Sun
5/2D
P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF
6:30 8:30 12:00 12:00 16:30 22:30
7:30 10:00 12:00 12:00 17:00 23:00
All 7 days
7D
P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF
6:30 8:30 12:00 12:00 16:30 22:30
Everyday
24H
P1 ON P1 OFF P2 ON P2 OFF P3 ON P3 OFF
6:30 8:30 12:00 12:00 16:30 22:30
Contents
1. Factory default settings
2. Factory program settings
3. Resetting the programmer
4. Setting the date and time
5. ON/OFF period selection
6. Adjusting the program settings
7. Copy function
8. Reviewing the program settings
9. Boost function
10. Advance function
11. Holiday mode
12. Backlight mode selection
13. Keypad lock and unlock
14. Frost protection function
15. Master reset
R37 - 3 Zone Programmer Operating Instructions
Page 2 of 2
8. Reviewing the program settings
9. Boost function
10. Advance function
This function allows the user to bring forward the next switching time.
If the zone is currently timed to be OFF and the ADV is pressed, the zone will
be switched ON until the end of the next switching time.
If the zone is currently timed to be ON and the ADV is pressed, the zone will
be switched OFF until the end of the next switching time.
Press for Zone 1, for Zone 2 or for Zone 3.
To cancel the ADVANCE function, simply press the respective ADV
button again.
Lower the cover on the front of the unit.
Move the selector switch to the PROG SET position.
By pressing this will review each of the ON/OFF times for P1 to P3 for
Zone 1.
Repeat this process to review the ON/OFF times for Zone 2 by pressing
and then pressing
Repeat this process to review the ON/OFF times for Zone 3 by pressing
and then pressing
When completed, move the selector switch to the RUN position.
This function allows the user to extend the ON period for 1, 2 or 3 hours.
If the zone that you wish to Boost is timed to be OFF, you have the facility to
switch it ON for 1, 2 or 3 hours.
Press the required button: for Zone 1, for Zone 2 and for Zone 3
once, twice or three times respectively.
To cancel the boost function, simply press the respective boost button again.
ZONE
1
Boost
ZONE
2
Boost
ZONE
3
Boost
ZONE
1
ADV.
ZONE
2
ADV.
ZONE
3
ADV.
3
11. Holiday mode
Lower the cover on the front of the unit.
Move the selector switch to the RUN position.
Press the button.
The current date and time will ash on the screen. It is now
possible to enter the date and the time when you plan to return.
Press the or buttons to adjust the holiday period requried.
Press the button.
The programmer is now switched OFF for the selected number of days.
By pressing the button again, this will cancel the holiday mode,
thereby returning the programmer to the normal settings.
RUN
CLOCK
SET
PROG
SET
Holiday
There are two settings for selection. The factory default setting is ON.
ON The backlight is permanently ON.
AUTO On pressing any button the backlight stays on for 10 seconds.
To adjust the backlight setting, lower the cover on the front of the unit.
Move the selector switch to the RUN position.
Press the button for 5 seconds.
Press either the or buttons to select the ON or AUTO mode.
Press the button.
RUN
CLOCK
SET
PROG
SET
On
12. Backlight mode selection
To lock the keypad, press and hold the and buttons for 5
seconds.
will appear on the screen. The keypad is now locked.
To unlock the keypad, press and hold the and buttons for 5
seconds.
will disappear from the screen. The keypad is now unlocked.
Holiday
Holiday
Unlocked
13. Keypad lock and unlock
Selectable range 5~20°C. This function is set to protect pipes against
freezing or to prevent low room temperature when the programmer is
programmed to be OFF or is manually OFF.
Frost protection can be activated by following the procedure below.
Move the selector switch to the RUN position.
Press both the and buttons for 5 seconds, to enter selection mode.
Press either the or buttons to to turn On or turn O frost
protection.
Press the button to conrm.
Press either the or buttons to increase or decrease the desired
frost protection setpoint.
Press the button to select.
Both HOT WATER and HEATING zones will be switched ON in the event of
room temperature falling below the frost protection setpoint.
When frost protection is enabled “Frost” will be visible on the screen.
When frost protection is activated “Frost” will ash on the screen.
RUN
CLOCK
SET
PROG
SET
14. Frost protection function O
Lower the cover on the front of the programmer.
There are four hinges holding the cover in place.
Between the 3rd and 4th hinges there is a circular hole.
Insert a ball point pen or similar object to master reset the programmer.
After pressing the master reset button, the date and time will now need
to be reprogrammed.
15. Master reset
20221107_R37_OpIns_PK
EPH Controls Ireland
technical@ephcontrols.com www.ephcontrols.com
EPH Controls UK
technical@ephcontrols.co.uk www.ephcontrols.co.uk
RUN
CLOCK
SET
PROG
SET
/
