ZC-Y41PH4
COLOR CCD CAMERA
INSTRUCTION MANUAL
12
12
PART DESCRIPTION
(1) CS lens mount
(2) Back Focus adjustment lever
(3) Back Focus lock screw
(4) DC auto iris connector
(5) Mounting screw hole, 1/4”, 7mm deep
(6) DIP Switches
11
11
(7) Video auto iris connector potentiometer
(8) BNC connector for video output
(9) V-Phase adjustment potentiometer
(10) ALC Level adjustment
(11) LED lamp
(12) Power input terminal
Thank you for your purchase of this product.
Before operating the product, please read this instruction manual carefully to
ensure proper use of the product.
Please store this instruction manual in a safe place for future reference.
The installation should be made by a qualified service person or system installers
and should conform to all local codes.
If an abnormality should occur, immediately turn off the power and contact qualified
service professionals for instruction.
WARNING
Day and night function provide high quality color picture in the normal lighting
conditions (day mode) and automatically switch to black & white picture in the
low light conditions (night mode).
540 TV line horizontal resolution
DIP switches allow users to set up various parameters easily including Line
Lock, Day/Night mode, back light compensation, and many more.
Low image distortion and residual, withstanding electric and magnetic field
interference and mechanical vibration.
Signal to noise ratio of 48dB.
Minimum illumination of 0.3 lx.
Accurate color reproduction.
Easy backfocus adjustment function allows quick installation.
Use only 24VAC or 12VDC regulated power supply marked class 2.
To prevent fire or electrical shark, UL listed class 2 wiring should be used for the
power input terminal.
Use only power source and connectors that have been approved in your country
and comply with the international standards.
Be sure to connect each lead to the appropriate terminal. Wrong connection may
cause malfunction and/or damage to the video camera.
Do not attempt to aim the camera at the sun or other extremely bright objects
that cause smear to appear irrespective of whether the camera is operating or
not. This can damage the CCD (Charge Coupled Device).
Do not place the camera in the following locations
- Locations subject to extremely high or low temperatures.
(Operating temperature range: -10°C to +50°C {14°F to 122°F})
(Storage temperature range: -20°C to +60°C {-4°F to 140°F})
- Locations subject to high levels of humidity and dust.
(Operating humidity range: max 85% {No condensation})
(Storage humidity range: max 95% {No condensation})
- Locations where there are large amounts of water vapor and steam.
Ensure the location selected is sufficiently strong enough to support the weight of
the camera and is free from vibration.
When this camera is installed near equipment that emits a strong electromagnetic
field, some irregularity such as noise on the monitor screen may happen.
Be sure to use screws suitable for the type of material to which the camera is being
mounted.
Do not allow the camera to be subjected to strong impacts or shocks. The camera
could be damaged by improper handling or storage.
Never attempt to disassemble or modify the camera.
If an abnormality should occur, immediately turn off the power and consult your
dealer.
When the camera is not in use, put the lens cap on to protect the CCD
sensor.
FEATURES
SAFETY PRECAUTIONS
CAUTION
To prevent fire or electrical shock, do not expose this appliance to rain or moisture.
1 When this crossed-out wheeled bin symbol is attached to a product it means the product is covered
by the European Directive 2002/96/EC.
2 All electrical and electronic products should be disposed of separately from the municipal waste
stream via designated collection facilities appointed by the government or the local authorities.
3 The correct disposal of your old appliance will help prevent potential negative consequences for the
environment and human health.
4 For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
The CE Marketing is a Directive Conformity mark of the European Union (EU)
Camera (1)
Instruction Manual (1)
CCD Protection Cover (1)
PACKAGE
SPECIFICATION
Model
TV System
Image Sensor
Effective Picture Element
Horizontal Resolution
Synchronization
Scanning System
Scanning Frequency
S/N Ratio
AGC Control
Operating Temperature
Storage Temperature
Video Output
Power Supply
Power Consumption
IRIS Connector
Automatic
Electronic Shutter (second)
Minimum Illumination
Auto White Balance
Back Light Compensation
Dimensions
Weight
ZC-Y41PH4
PAL
1/3” Format Interline CCD Sensor
752(H) x 582 (V)
540 TV line
Internal / Line Lock
2:1 Interlace
H:15625Hz V:50.0Hz
48 dB
Normal / Turbo
-10ºC to +50ºC
-20ºC to +60ºC
Composite video signal,
1V(p-p), 75Ω (BNC)
DC / AC 50Hz,
12VDC / ~24VAC ± 10%
4.5W Max.
4 pin Connector for DC Drive Lens / 3 Pin
Terminal Block for Video Drive Lens
Auto illumination Control
1/50 - 1/100000
0.3 lx @ F1.2
2700°K ~ 9700°K
Off / On
62mm (W) x 58mm (H) x 120mm (L),
260 g (without lens)
099-1.0
DIP SWITCHES SETTING
1. Loosen the back focus adjustment lever located
on the front head.
2. Adjust the screw to a desired position, and then
fix the screws.
Caution for focus adjustment:
1. Do not over-tighten the back focus screw.
2. Do not attempt to use any tools other than fingers to tighten the screw.
Improper focus adjustment may result in severe damages to the back-focus
echanism or to the CCD image sensor.
POTENTIOMETER SETTING
→ Refer to PARTS DESCRIPTION (9) & (10)
LEVEL (Auto Lens Control Level Adjustment)
This potentiometer controls DC lenses:
it manages CCD sensor light quantity by adjusting lens IRIS aperture.
V-Phase (Line Lock Phase Adjustment)
When the camera is set to Line-Lock mode (LL), it is possible to adjust camera
triggering point on the AC cycle in case of systems using sequential switchers
devoid of image digital process feature or video matrixes.
See also ’DIP SWITCH SETTING’ (LL/INT).
Focus Adjustment
→ refer to PARTS DESCRIPTON (2) & (3)
→ Refer to PARTS DESCRIPTION (6)
The row of DIP switches allow the following settings to be made:
LL / INT
The line-lock mode enables the AC line phase adjustment.
Note: The line-lock sync mode is not available when the camera operates on DC
power.
SDN / ON
This feature enables the camera operates in monochrome mode in reduced lighting.
Switch to ON to activate.
BLC / ON
The Backlight Compensation feature eliminates the effect of strong background
lighting, maintaining the correct exposure. Switch to ON to activate. When switched
to BLC, the feature is off.
AGC / TURBO
The Automatic Gain Control feature can improve picture quality in low lighting
conditions.
Select TURBO for most applications. Setting to AGC will reduce 'noise' from the
image,
but it will also limit the camera's sensitivity.
AES/ ON
Selecting ON enables Electronic Iris mode, which compensates for excessive light
levels by automatically adjusting the camera shutter speed. This mode should only
be used with fixed or manual iris lenses.
F.L. / ON
When this switch is set to ON, the camera reduces flicker in the image under
fluorescent lighting.
Connect the power cable to the power input connector or terminal on the rear panel.
The camera automatically detects the power source (DC12V/AC24V).
Make sure the proper polarity for DC source.
Use RED terminal for +12VDC and BLACK for ground connection.
Improper polarity may cause damage to camera.
The Power LED on the rear panel is lit when the camera is connected to a power
source (refer to Parts Description 11).
Important Note:
Qualified service personnel or system installers should perform the installation.
Make sure that the power is OFF before handling the power supply cable.
Connect the 75Ω coaxial cable to video output terminal.
This camera supports manual iris lens, video auto iris lens,
and DC auto iris lens.
1. Video Auto Iris Lens Pin assignment
GND: Shield, ground.
+12V: Power source; +12VDC, 50 mA Max.
Video: Video signal output.
2. DC Auto Iris Lens
The 4 pin connection terminal is on the
rear panel. Refer to the pin assignment
to ensure the proper operation.
1. Mount a lens onto the camera lens mount. Turn the lens clockwise.
2. This camera can accept CS-mount lens, or C-mount lens with a 5 mm adaptor ring.
Cautions for lens mounting:
1. In case of using a lens heaver than the camera, the lens and camera will require
additional support.
2. Do not over-tighten the lens onto the camera mount.
3. Do not rotate the lens counter-clockwise.
Lens Mounting
→ refer to PARTS DESCRIPTON (1)
CONNECTION AND ADJUSTMENT
Power Supply Cable Connection
→ refer to PARTS DESCRIPTON (12)
Video Cable Connection
→ refer to PARTS DESCRIPTON (8)
Auto Iris Lens Connections
→ refer to PARTS DESCRIPTON (4) & (7)
/