Side-Power S-linkControl Panel PJC222 Installation and User Manual

Type
Installation and User Manual
Keep this
manual onboard !
Installation and user's manual
GB
Made in Norway
© Sleipner Motor AS 2012
SLEIPNER MOTOR AS
P.O. Box 519
N-1612 Fredrikstad
Norway
Tel: +47 69 30 00 60
Fax: +47 69 30 00 70
www.side-power.com
sidepower@sleipner.no
PJC-222
S-link
Control Panel
SIDE-POWER
Thruster Systems
v 1.0.6
2PJC-222 1.0.6 - 2012
STOP
front s_v strek_PJC222.pdf 1 04.11.2010 11:05:34
PJC-222
Control panel with S-link CAN-bus connection
Product features
• ForproportionalthrustercontrolwithSide-Powerhydraulicthrustersystems
• Fingertipcontrolspeedcontrolwithpurposedesignedjoysticks
• Hold-functionforeasydocking,runsthrustersatselectedpower
• Back-litLCDdisplaywithinstantfeedback
 - Systemstatus
 - Amountofthrust&directionofthrust
 - Oiltemperature
• Interactivemulti-languagemenus
• CAN-Buscommunicationwiththrustersandaccessories
• Plug&playcables,waterproofandcompactconnectors
• Built-inaudiblealarm“buzzer”
• Connectorforexternal“buzzer”/loudaudiblealarms
Speedcontroljoystickfor
bowthruster
Speedcontroljoystickfor
sternthruster
Holdingfunctionforauto-
runningofbowandstern
thrusterstogetherinthe
directionofthearrowsat
selectedpower
Press“+”formoreand
“-”forlesspower.
Ifothercontrolunitsare
runningthethrusterinop-
positedirectiontothehold
function,theholdfunction
willbedeactivated. Informationdisplay,see
followingpagesfordetails.
Pressandhold“ON”button
for3secondstoactivate
controlpanel.
Presstochange
betweendayand
nightlight.
Pressandholdfor
3secondstoenter
menusystem
Emergencystop
button
Presstode-activate
controlpanelorcancelor
gobackinmenusystem
DONOTconnectanyothercontrolequipmenttotheS-linkcontrolledproductsexcept
Side-PoweroriginalS-linkproductsorviaaSide-Powersuppliedinterfaceproductmade
forinterfacingwithothercontrols.Anyattempttodirectlycontroloratallconnectinto
theS-linkcontrolsystemwithoutthedesignatedandapprovedinterface,willrenderall
warrantiesandresponsibilitiesforthecompletelineofSide-Powerproductsconnected
voidandnull.IfyouareinterfacingbyagreementwithSleipnerandthroughadesignated
Side-Powersuppliedinterface,youarestillrequiredtoalsoinstallatleastoneoriginal
Side-Powercontrolpaneltoenableefcienttroubleshootingifnecessary.
3
PJC-222 1.0.6 - 2012
DISPLAY IN NORMAL USE:
Bow thruster information
Oiltemperature
intank
Stern thruster information
WARNING AND ALARMS:
Whenthereisaproblemorafault,thepanelwillshowthisalarmsituationbytheLCDdisplayinredcolor.
AllalarmsandwarningswillshowindisplaywhenpanelisturnedOFF.ThisrequirestheS-linkandothersystem
deviceshaspower.Criticalalarmsarealsotrigginginternalandexternalbuzzer.Thebuzzercanbesilencedby
pushingtheOFFbutton,thiswillalsosilenceallotherpanelsinthesystem
Criticalalarms:LOWOILLEVEL,HIGHOILTEMPERATURE,EMERGENCYSTOP,HIGHSPEEDSTABILIZERNOTAC-
TIVEandHYDRAULICACMOTORPOWERPACKOVERTEMP,ACTHRUSTEROVERTEMP,ACTHRUSTERFAIL,STABI-
LIZERFAULT
For safety!
When oil pressure goes below 10bar, the HOLD function are deactivated.
FILTER Warnings (if lter censors are installed)
ReturnFilter:Areturnltersymbolappearsandashes,upperright,when
 thereturnlterelementrequiresreplacing.
Pressurelter:Apressureltersymbolappears&asheslowerright,when
 thepressurelterelementrequiresreplacing.
Warningswilldisappearautomaticallywhenthelterelementsarereplaced
Thrusterscanbeoperatedwhenthelterwarningsareshown.
ALARMS
OIL LEVEL & TEMPERATURE (FIG. 1)
Whentheoillevelislow,thescreenwillilluminatered,aexternalbuzzerwill
sound&alowoillevelsymbolwillappear&ashupperleft
Whentheoiltemperatureishigherthan75°Cthescreenwillilluminatered,a
internalbuzzerwillsound&andtheoiltempsymbolwillash.Thealarmwill
stopwhenthetemperaturedropsbelow65°C.

ThebuzzercanbesilencedbypushingtheOFFbutton.
Thethrusterscanbeoperatedwhenthealarmsareactive.
COMMUNICATION FAILURE (FIG. 2)
Whenthepanelloosescommunicationwithtankequipmentthescreenwillil-
luminateredandasymbolforcommunicationfailurewillashinthecentreof
thescreen.Bothinternal&externalbuzzerswillsound.
ThebuzzercanbesilencedbypushingtheOFFbutton.
STOP BUTTON (FIG. 3)
PressingtheSTOPbuttonwillthedumpvalveoperateandthethrusterwill
stop.NB:FOREMERGENCYUSEONLY
WARNING! HIGH SPEED. STABILIZER NOT ACTIVE! (FIG. 4)
(OnlyforyachtsequippedwithaSide-PowerStabilizersystem)
Warningwillshowwhenyachtisdrivenathighspeedwithstabilizersystem
inactive.PleaserefertotheStabilizer ECU manualforspeedsettings.
Thrustpoweranddirection
Thrustpoweranddirection
FIG.1
FIG.2
FIG.3
FIG.4
Indicatingamountofthrustsetbyothercontrolunitsinthesystem,i.eadditonalPJC-322/321/222/221panels,
inputvia8730S-linkexternalswitchinterface(remotecontrol,footswitchesetc.)
Iftwoormoreunitsissettorunthethrusterinoppositedirection,thisinformationwillnotbeshown.
4PJC-222 1.0.6 - 2012
AC MOTOR ALARMS
HYDRAULICACMOTORPOWERPACKOVERTEMP:
Theovertempsymbolwillshowintheupperrightcornerofthedisplay
whentheACmotortemperatureisabove120°Candautomaticallyreset
whentemperaturegoesbelow110°C.


HYDRAULICACMOTORPOWERPACKTEMPSENSOR:
TheACmotortempsensorfailsymbolwillshowintheupperrightcorner
ifthesystemissetupwithanhydraulicACmotorpowerpackandthe
sensorhasanopencircuit.
STABILIZER ALARM
(OnlyforyachtsequippedwithaSide-PowerStabilizersystem)
Alarmwillshowwhenanstabilizeralarmoccurs.Seestabilizer
panelformoredetailedinformation.
Clear:Clearsthealarminthepanelandmutesthebuzzeralarm
5
PJC-222 1.0.6 - 2012
AC THRUSTER
IfanSACthruster(s)isinstalledyouwillseeanACmotorsymbol
correspondingtotheinstalledlocation.Therecanbeupto4SAC
thrustersinstalled.ThesymbolsshowsupautomaticwhenSAC
thrustersisinstalledandneedsnoextrasetupfromthepanel.
AC THRUSTER ALARMS AND WARNINGS
Allalarmscanbemutedbypushingthe“OFF”button.
HIGH TEMP WARNING
WhentheSACreachthewarninglevel,thescreenwill
illuminatered,anbuzzerwillsound&theSACtemperature
willshowwithaW.
SeeSACManualformoredetails.
HIGH TEMPERATURE ALARM
WhentheSACreachthealarmlevel,thescreenwill
illuminatered,anbuzzerwillsound&theSACtemperature
willshowwithaAL.
SeeSACManualformoredetails.
TEMPERATURE SENSOR FAIL
Whenthereissomethingwrongwiththetemperature
sensorintheSACorbadconnection-thescreenwillilluminatered,
abuzzerwillsound&SENSORwillshow.
VFD WARNING
WhenthereisanwarningfromtheVFD,thescreen
willilluminatered,anbuzzerwillsound&VFDsymbolwith
WARNINGwillshow.
SeeSACManualformoredetails.
VFD NOT READY
WhentheVFDisnotready,thescreenwillilluminatered,
anbuzzerwillsound&VFDsymbolwithNOTREADYwillshow.
Andthethrusterstops.
SeeSACManualformoredetails.
VFD FAULT
WhenthereisanalarmfromtheVFD,thescreenwill
illuminatered,anbuzzerwillsound&VFDsymbolwith
ALARMwillshow,andthethrusterstops.
SeeSACManualformoredetails.
6PJC-222 1.0.6 - 2012
STOP
front s_v strek_PJC222.pdf 1 04.11.2010 11:05:34
MENU SYSTEM:
Access menu system by pressing and holding menu button
(‘ON’ button) for 3 seconds
Move around in menus by using joysticks
Follow instructions on the screen and press buttons as indicated on
LCD screen
STABILIZER
STABILIZER
(ShownonlyforyachtsequippedwithaSide-PowerStabilizersystem)
STABILIZER:SwitchesthestabilizerONorOFF.
AnySpeed:SwitchestheAnySpeedfunctionONorOFF.
OK: Changesstabilizersettingandreturnstomainmenu.
Select: Selectingparameter.
Cancel: Returnstomainmenuwithoutchanges.
Usesternjoysticktomakechanges.
LANGUAGE
LANGUAGE
Chooselanguagebymovingjoystick:
English,Norwegian,German,French,SpanishandItalian.
OK: SaveslanguagesetupandreturnstoMainMenu
Cancel:Returnsto“SETUP”-menuwithoutsavingchanges
SETUP
SETUP
Usesternjoysticktochoosefunction
Select:Opensselectedfunction
Cancel:ReturnstoMainMenu
PUMPSETUP
CoolingPump:ThecoolingpumpcanbeselectedtoONorAuto
WhenAutoisselectedthecoolingpumpwillstartoperationwhen
theoiltemperaturereaches50°Candstopwhentheoiltemp
dropsbelow40°C.
PUMP1(PTOmounted):Pump1canbesettoOFF,ONorAUTO.
Whenpump1issettoauto,thepumpisonwhenanypanelis
turnedonandoffwhenallpanelsareoff.Thiscanbeusedto
controlahydraulicACmotorpowerpackorelectricclutch.
PUMP2(PTOmounted):Pump2couldbesettoONorAUTO.When
Pump2issettoautoandSPSstabilizersarerunning,thepumpwill
startautomaticallywhentheoilpressuredropsbelow80Barand
keeprunningfor15min.oraslongasthethrustersarerunning.
WhenSPSstabilizersareinactive,Pump2willrunallthetime.
TheAUTOfunctionisusedforreducedenergyconsumptionwhile
SPSStabilizersarerunning.
NB: only to be used with PHC24 controller with rmware
1.008 or newer!
HOLDCALIBRATION
CalibratestheHOLD-functiontogetbalancedthrustfromthe
bowandsternthruster.
Start: Startscalibration.Aninstructionexplainingthe
calibrationprocedurewillbeshownonthedisplay.In 
  somelanguagesitwillbenecessarytopress“More”to
  readthecompleteinstructions.
  Pressportorstarboard“HOLD”-buttonforcalibrationin
  thedesireddirectionThiswillmakeboththrustersrunin
theselecteddirection.Adjustamountofbowthrust 
  withbowjoystickandsternthrustwiththesternjoystick
  untilabalancedthrustisachieved
7
PJC-222 1.0.6 - 2012
NB! NB!
SETUP
(cont.)
OK: Savesthecalibrationsetupandreturnsto“SETUP”- 
  menu
Cancel:Returnsto“SETUP”-menuwithoutsavingchanges
Anychangesmadewillberelayedtoallotherinstalledpanels
(Firmware1.007ornewer)
RADIOREMOTESETUP
AdjuststheamountofthrustwhichtheON/OFFremotecontrol
willrunat.Usejoystickstoadjustappliedthrust
OK: Saveschangesandreturnsto“SETUP”-menu
Cancel:Returnsto“SETUP”-menuwithoutsavingchanges
Anychangesmadewillberelayedto8730INTERFACEunitswith
Firmware1.203ornewer
SYSTEMDEVICES
ViewalldevicesconnectedtoS-Linkandmanuallychangesetup
values.
Slidebetweendeviceswiththejoysticktoseedeviceinformation
aslocation,thrusterdirection,retracttype,rmwareversionand
serialnumber.
Edit:ChangelocationtoBOW,STERN,BOW-PORTorSTERN-
PORT,thrusterdirectiontoNormalorInvertedorretract
type.ForAutomaticmainswitch18977andinterface
8730,youcanonlychangelocation.Usejoysticktoalter
values.
Location:
 CanchangeselecteddevicelocationbetweenBOW,
STERN,BOW-PORTorSTERN-PORT.ForPPC800or
SR61242only.(useBOW-PORTonsecondbowthruster
andSTERN-PORTonsecondsternthruster)
Direction:
 CanchangethrusterdirectiontoNormalorInverted.
Changethisvalueifthethrusterisrunninginthewrong
direction.ForPPC800orSR61242only.

Retract:
 Setupretracttypes.ForPPC800orSR61242only.
 Normal: standalone,usethisforPPC800withoutany
  retractorSR61242(SR80/100)without
  PPC800orSR150000(SR130/170/210)
  withoutPPC800.
Type 1: RetractSR61242(SR80/100)withPPC800,
  bothdevicesneedstobesettoType1.
Type 2: RetractSR150000(SR130/170/210)with
  PPC800,bothdevicesneedstobesetto
Type2 
WHEN INSTALLING A RETRACT THRUSTER WITH
SPEED CONTROL (PPC800), DO NOT TRY TO RUN
THE THRUSTER UNTIL YOU HAVE COMPLETED THE
ENTIRE SETUP PROCEDURE CORRECTLY!
 Thisistopreventdamagetothethrustercausedbyrun-
ningthethrusterwhiletheretractmechanismisnotfully
opened.
OK: Saveschangesandquitediting.
Select:SwitchbetweenLocation,RetractandRetractset-
tings.
Cancel:Canceloperationwithoutsavingchanges.
Cancel:Returnsto“SETUP”–menu.
8PJC-222 1.0.6 - 2012
PANEL
PANEL SETUP
BACKLIGHTLEVEL
 Setlevelofpanelbacklightindaylightmode,1-5
NIGHTLIGHT-COLOR
 Selectcolorofbacklightinnightlightmode:
 GREEN,BLUE,RED,WHITE
NIGHTLIGHT-LEVEL
 Setlevelofpanelbacklightinnightlightmode,1-3
TIMERAUTOOFF
 Setthetimefromlastusetoautopanelshutdown.
 Setfrom5-60minutesin5minutestepsorOFF(panelwill
 notturnoffautomatically)
OK: Saveschangesandreturnstomainmenu
Select: Selectingparameter
Cancel:Returnstomainmenuwithoutsavingchanges
Usesternjoysticktochangevalueupordown
DEFAULT
DEFAULT SETTINGS
Resetallsettingstofactorydefault-followinstructionsonscreen
Start: Resetssystemtodefaultfactorysettings
Cancel:Returnstomainmenuwithoutchanges
INFO
INFO
Theinfoselectionisaservicescreen.
ChoosetheInfoscreenifyouwishtocheckyoursystem.
Usejoysticktohighlightdesiredchoice.
Select:Selectshighlightedinfomenu.
Back:Returnstomainmenu.
PANELINFO
Showspanelsrmwareversion,hardwareversion,serialnumber
andS-Linkvoltageintothepanel.
Back:ReturnstoInfomenu.
HYDRAULICINFO
Showssystempressureandoiltemperature.
Thrustercanbeoperatedwiththejoystick.
STOP:Emergencystop–ActivatesdumpvalveandStopthrusters.
Back:ReturnstoInfomenu
ACTHRUSTERINFO
ShowsACthrustertemperatureandrpmforeveryACthrusters
installed.BlanksquareindicatesnoACthrusterinstalledinthis
instance.Thrustercanbeoperatedwiththejoystick.
STOP:Emergencystop–Stopthrusters.
Back:ReturnstoInfomenu.
9
PJC-222 1.0.6 - 2012
S-link System Overview, Hydraulic
STATION 1 STATION 2
(OPTIONAL)






































 









10 PJC-222 1.0.6 - 2012





























S-link System Overview, AC
11
PJC-222 1.0.6 - 2012
Supply
+12V / 24V DC
(S-link)
+
-
External alarm buzzer
12V / 24V DC - max 0,5A
Internal
fuse/relay
External alarm/buzzer connection
Rearside
ofpanel
Connections for optional external buzzer/audible alarm





 









Panel cutout templatePanel dimensions


Argentina
Trimer SA
Buenos Aires
Tel: +54 11 4580 0444
Fax: +54 11 4580 0440
www.trimer.com.ar
trimer@trimer.com.ar
Australia
AMI Sales
Freemantle, WA
Tel: +61 89 331 0000
Fax: +61 89 314 2929
Austria
G. Ascherl GmbH
Hard, Bregenz
Tel: +43 5574 899000
Fax: +43 5574 89900-10
www.ascherl.at
Benelux
ASA Boot Electro
Watergang
Tel: +31 20 436 9100
Fax: +31 20 436 9109
www.asabootelectro .nl
Brazil
Electra Service Ltda.
Guaruja
Tel: +55 13 3354 3599
Fax: +55 13 3354 3471
www.electraservice.br.com
Bulgaria
Yachting BG
Burgas
tel: +359 56 919090
fax: +359 56 919091
www.yachting.bg
Canada
Imtra Corporation
New Bedford, MA
Tel: +1 508 995 7000
Fax: +1 508 998 5359
www.imtra.com
China/Hong Kong
Storm Force Marine Ltd.
Wanchai, Hong Kong
Tel: +852 2866 0114
Fax: +852 2866 9260
www.stormforcemarine.com
Croatia
Yacht Supplier
Icici
Tel: +385 51 704 500
Fax: +385 51 704 600
Denmark
Gertsen & Olufsen AS
Hørsholm
Tel: +45 4576 3600
Fax: +45 4576 1772
www.gertsen-olufsen.dk
Finland
Nautikulma OY
Turku
Tel: +358 2 2503 444
Fax: +358 2 2518 470
www.nautikulma.fi
nautikulma@nautikulma.fi
France
Kent Marine Equipment
Nantes
Tel: +33 240 921 584
Fax: +33 240 921 316
www.kent-marine.com
Germany
Jabsco GmbH
Norderstedt
Tel: +49 40 535 373-0
Fax: +49 40 535 373-11
www.xylemflowcontrol.com
Greece
Amaltheia Marine
Athens
Tel: +30 210 2588 985
Fax: +30 210 2588 986
www.amaltheiamarine.com
Iceland
Maras EHF
Reykjavik
Tel: +354 555 6444
Fax: +354 565 7230
www.maras .is
gummi@maras .is
India
Indo Marine Engineering Co. Pvt. Ltd
Pune, Maharashtra
Tel: +91 20 2712 3003
Fax: +91 20 2712 2295
siddharth@indogroup-asia.com
Ireland
Sleipner Motor Ltd.
South Brent
Tel: +44 1364 649 400
Fax: +44 1364 649 399
andy@sleipner.co.uk
Israel
Atlantis Marine Ltd.
Tel Aviv
Tel: +972 3 522 7978
Fax: +972 3 523 5150
www.atlantis-marine.com
atlantis@inter.net.il
Spain
Imnasa Marine Products
Girona
Tel: +34 902300 214
Fax: +34 902 300215
www.imnasa.com
Sweden
Sleipner AB
Strömstad
Tel: +46 526 629 50
Fax: +46 526 152 95
www.sleipnerab.se
Switzerland
Senero AG
Winterthur
Tel: +41 52 203 66 55
Fax: +41 52 203 66 56
www.senero .ch
info@senero .ch
Singapore/Malaysia/
Indonesia/Vietnam/Phillipines
Island Marine Services Pte Ltd
Singapore
Tel: +65 6795 2250
Fax: +65 6795 2230
www.island-marine.com
Taiwan
Mercury Marine Supply
Kaohsiung
Tel: +886 7 3317 293
Fax: +886 7 3314 232
Turkey
Denpar Ltd.
Istanbul
Tel: +90 212 346 1332
Fax: +90 212 346 1329
U K
Sleipner Motor Ltd.
South Brent
Tel: +44 1364 649 400
Fax: +44 1364 649 399
andy@sleipner.co.uk
United Arab Emirates
Teignbridge Propellers & Marine
Equipment Co. Ltd.
Dubai
Tel: +971 4 324 0084
Fax: +971 4 324 0153
USA
Imtra Corporation
New Bedford, MA
Tel: +1 508 995 7000
Fax: +1 508 998 5359
www.imtra.com
Italy
Saim S.P.A.
Assago-Milan
Tel: +39 02 488 531
Fax: +39 02 488 254 5
www.saim-group.com
Japan
Turtle Marine Inc.
Nagasaki
Tel: +81 95 840 7977
Fax: +81 95 840 7978
www.turtle-marine.com
Malta
S & D Yachts Ltd.
Cali
Tel: +356 21 339 908
Fax: +356 21 332 259
www.sdyachts.com
New Zealand
Advance Trident Ltd.
Auckland
Tel: +64 9 845 5347
Fax: +64 9 415 5348
www.advancetrident.com
Norway
Sleipner Motor AS
Fredrikstad
Tel: +47 69 30 00 60
Fax: +47 69 30 00 70
www.side-power.com
sidepower@sleipner.no
Poland
Taurus Sea Power SP. Z.O.O
Gdansk
Tel: +48 58 344 30 50
Fax: +48 58 341 67 62
Portugal
Krautli Portugal Lda.
Lisboa
Tel: +351 21 953 56 00
Fax: +351 21 953 56 01
www.krautli.com
Russia
Standarte
Starbeyevo
Tel: +7 495 575 67 23
Fax: +7 495 575 39 77
www.standarte.ru
South Africa
C-Dynamics
Cape Town
Tel: +27 21 555 3232
Fax: +27 21 555 3230
www.c-dynamics.co.za
Cyprus
Ocean Marine Equipment Ltd
Limassol
Tel: +357 253 69731
Fax: +357 253 52976
Estonia/Latvia/Lithuania
Miltec Systems OÜ
Tallin
Tel: +372 5013997
Fax: +372 6442211
www.miltec.ee
Sleipner Motor AS • P. O. Box 519, N-1612 Fredrikstad • Norway
Tel: +47 69 30 00 60 • Fax: +47 69 30 00 70 • sidepower@sleipner.no • www.side-power.com
Service Centres
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Side-Power S-linkControl Panel PJC222 Installation and User Manual

Type
Installation and User Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI