Cool-Icam CIC-280 User manual

Brand: Cool-Icam

Model: CIC-280

Type: User manual

This manual is also suitable for

User’s Manual

1. Introduction

Congratulations on purchasing the G2. Using the latest innovations in technology the G2 offers fun, affordable and easy to

use digital imaging.

Although you probably want to get started right away, please take a few minutes to read this guide and familiarise yourself

with your new G2. Your new G2 will take 25 Hi-Res (High Resolution), 80 Normal-Res (Normal Resolution) or 160 Low-Res

(Low Resolution) images, which you upload to your PC (Personal Computer) running Windows®98SE, Windows® Me, 2000,

XP or Macintosh® running versions OS 8.6 - 9.2.

You can also use your G2 to capture not only snaps of your family and friends, but also video clips of them in action. Your

digital images and video clips can also be played back on your TV.

Your G2 can also be used as a Web Cam. If you have an internet connection and microphone (not supplied) you can chat

face-to-face with friends and colleagues, conferencing in real time.

Your G2 is equipped with 8MB of internal memory, additional memory for storing digital images and video clips can be added

by inserting a SmartMedia™ Card (SMC) (sold separately) in the G2 memory card slot provided. When you have taken your

images, the G2 will wait for 60 seconds and then automatically switch to Stand-by mode to preserve battery life.

www.cool-icam.com

2. Table of Contents

1. Introduction ................................................................................................................................................ 1

2. Table of Contents ........................................................................................................................................ 2

3. System Requirements................................................................................................................................... 3

4. Package Contents......................................................................................................................................... 3

5. Software Installation .................................................................................................................................... 3

For Windows® Users:

5.1 How to install the My Digital Camera Software ..........................................................................................3

5.2 How to use ArcSoft® Software .................................................................................................................4

5.3 How to install Microsoft® NetMeeting™ ......................................................................................................4

5.4 How to install Adobe® Acrobat® Reader.....................................................................................................4

5.5 How to install QuickTime™........................................................................................................................5

For Macintosh® Users:

MAC

5.6 How to install the My Camera Software .....................................................................................................5

5.7 How to install ArcSoft® Software ..............................................................................................................5

5.8 How to install Adobe® Acrobat® Reader.....................................................................................................5

5.9 How to install QuickTime™........................................................................................................................5

6. Battery Installation........................................................................................................................................6

7. Getting to Know Your G2 ................................................................................................................................6

7.1 LCD Display ............................................................................................................................................6

7.2 Power ....................................................................................................................................................6

7.3 SmartMedia™ Card Slot............................................................................................................................7

8. Getting Started.............................................................................................................................................8

8.1 Switching the G2 On ...............................................................................................................................8

8.2 G2 Controls ............................................................................................................................................8

8.3 Taking an Image......................................................................................................................................9

8.4 Taking a Movie Clip ..................................................................................................................................9

8.5 Erasing Contents from your G2 ..................................................................................................................9

9. Connecting your G2 to your Computer .............................................................................................................9

10. Uploading Images to Your Computer.............................................................................................................. 10

For Windows® Users:

10.1 Uploading Images and Movie Clips to your Computer ................................................................................ 10

For Macintosh® Users:

MAC

10.2 Uploading Images and Movie Clips to your Computer ................................................................................ 10

10.3 Viewing Images Using TV Output ........................................................................................................... 10

10.4 LCD Display Quick Reference Guide ........................................................................................................ 12

11. How to Use Other Softwares ......................................................................................................................... 12

For Windows® Users:

11.1 How to use PhotoStudio® 4.0................................................................................................................ 12

11.2 How to use ArcSoft Funhouse™ 1.0 ........................................................................................................13

11.3 How to use ArcSoft PhotoPrinter® 2000.................................................................................................. 13

11.4 How to use ArcSoft VideoImpression™ 1.6 .............................................................................................. 14

11.5 How to use Microsoft® NetMeeting®...................................................................................................... 14

11.6 How to use Adobe® Acrobat® Reader .................................................................................................... 15

11.7 How to use QuickTime™ ....................................................................................................................... 15

For Macintosh® Users:

MAC

11.8 How to use PhotoStudio® 4.0................................................................................................................ 15

11.9 How to use ArcSoft Funhouse™ 1.0 ........................................................................................................15

11.10 How to use ArcSoft PhotoPrinter® 2000 ................................................................................................ 16

11.11 How to use Adobe® Acrobat® Reader .................................................................................................. 16

11.12 How to use QuickTime™...................................................................................................................... 16

12. ArcSoft WorldWide Customer Support ............................................................................................................ 17

13. Troubleshooting ......................................................................................................................................... 18

14. Battery Guidance ........................................................................................................................................ 20

15. Technical Specications................................................................................................................................ 21

16. FCC Notice ................................................................................................................................................. 22

17. PAL/NTSC Table - TV Video Settings...............................................................................................................23

3. System Requirements

For Windows® Users

For Macintosh® Users

MAC

• PowerPC® Processor

• Mac® OS version 8.6 - 9.2

• USB port

• 128MB RAM

• 150MB Free disk space

• Color Monitor with High Color (16-bit) graphic capability

or higher

• CD-ROM Drive

• Standard mouse and keyboard

• Compatible with Microsoft® Windows® 98SE and Me, XP

• Pentium® 200MHz or higher recommended

• 128MB RAM or higher

• USB Port

• 200MB free disk space

• CD-ROM Drive

• Color Monitor with High Color 16-bit graphics capability or

higher

• Standard mouse and keyboard

4. Package Contents

USB Cable

Wrist Strap

with Clip

G2 Stand

(plus rubber stickers x 2)

(for customer assembly to

prevent slipping of G2)

G2 Software CD-ROM

(includes My Digital Camera,

PhotoStudio® 4.0 (PC & Mac),

ArcSoft Funhouse™ 1.0 (PC & Mac),

ArcSoft PhotoPrinter® 2000 (PC & Mac),

ArcSoft VideoImpression™ 1.6 (PC),

Microsoft® NetMeeting™ (PC),

Adobe® Acrobat® Reader (PC & Mac),

QuickTime™ 4 (PC & Mac),

User’s Manual (PC & Mac)).

Quick Setup

Instructions

Video Out Cable

5. Software Installation

For Windows® Users:

5.1 How to Install My Camera Software

Open & Close

5.1.1 How to Install My Camera Software

Your “My Digital Camera” should be installed rst.

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD-ROM drawer.

2. An installation wizard will automatically launch.

3. Click “My Digital Camera” icon.

4. Follow the instructions presented on the screen to complete the installation.

5. You will be asked to select between 50hz/60hz lighting frequency settings. Refer to the

note below and the troubleshooting guide.

6. Click “OK” to restart your computer and wait for your PC to restart automatically.

Notes:

If the setup screen doesn’t appear after loading the CD, then you can manually start it by double-clicking

the “My Computer” Icon on your desktop, then double-clicking the icon for the CD-ROM drive. When the

CD-ROM window opens, double-click the “digital camera” icon.

Frequency settings differ from country to country and some countries utilise both 50hz and 60hz. Note

for country with both settings test both settings. Follow 5.1.2 and 5.1.1 to uninstall and reinstall your My

Digital Camera software.

5.1.2 Creating a Desktop Icon

Double click on “My Computer” on your computer desktop. Right click on the icon “My Camera” and select “create shortcut”.

Select “Yes” and this will place “My Camera” icon on your computer desktop.

5.1.3 Creating a Desktop Folder to Hold your Images in

Right click on your computer desktop, select “New”. Select “Folder” and a new folder will appear on your computer desktop

and it will be waiting for you to name it by ashing. Call it “My Images”.

Now go to Section 5.2.

5.1.4 Uninstalling your My Digital Camera

To uninstall My Digital Camera, click the “Start Menu” -> “Settings” -> “Control Panels” -> “Add/Remove Programs”. Select

“My Camera” and click the “Add/Remove” button.

Notes:

Uninstalling your My Digital Camera does not delete your album folders and therefore all images transferred into your default or created albums

will be preserved. You will be able to access these folders on your system desktop.

5.2 How to Install ArcSoft® Software

Introduction to the Software

PhotoStudio

4.0

PhotoStudio

4.0 is a full-featured, easy-to-use digital image-editing program that provides a complete set of photo editing

and retouching tools, plus a wide selection of special effects and enhancements. Its powerful features include a wide variety

of input and output options, layers, multiple undo and redo functions, image management tools, editable text, multiple le

format support and a lot more.

ArcSoft Funhouse™ 1.0

ArcSoft Funhouse™ is an image entertainment application that enables users to create “fun photo” by combining their

personal photos with a wide variety of mask templates. Users can get their own images from digital cameras, scanners, disk

drives and Photo CDs, and seamlessly combine them with just a few clicks of the mouse. Photo mask includes sports, role

play, time warp, trading cards, in print, cartoon and surreal.

ArcSoft PhotoPrinter® 2000

ArcSoft PhotoPrinter® is an easy-to-use printing utility that enables the user to layout and print multiple images in different

sizes quickly and easily on a single sheet of paper. The program offers a large selection of printing templates, including Kodak

Digital Science Inkjet Photo Paper Templates and Avery-brand paper products. It also includes commonly used image-editing

tools and a wide selection of templates for frames, edges and backgrounds for enhancing images.

ArcSoft VideoImpression™ 1.6

ArcSoft VideoImpression™ is an easy-to-use video and image editing software program. The program enables users to create

and edit new videos using existing video and image les - making desktop video presentations for home, business, and the

Web.

Visit http://www.arcsoft.com for all your FAQ’s, tips and technical support see Section 12 for more details.

5.2.1 How to Install ArcSoft® Software

1. Reinsert the CD-ROM disc into the CD-ROM drive and close the CD ROM draw.

2. An installation wizard will automatically launch.

3. Click the “ArcSoft® Software” icon.

4. Select the language for the installation and click “OK”.

5. Follow the on-screen prompts.

6. Select the software you want or you do not want installed by clicking on the tick boxes

next to the software title. Click “Next >” to continue.

7. Follow the instructions presented on the screen to complete the installation.

Notes:

Don’t worry if you made a mistake and want to add in ArcSoft®

titles you did not tick. Reinsert the CD-ROM and follow steps 1 -

6 ticking only the software you want to add.

Please note that images saved in your computer memory

are able to be accessed via the ArcSoft® Suite software.

To access images in ArcSoft® from your G2 you must upload your images to your computer

as described in Section 10.1 for PC and 10.2 for Mac. See Section 11 for how to use

ArcSoft® software.

5.3 How to install Microsoft® NetMeeting™

NetMeeting™ provides the most complete conferencing solution for the Internet and corporate intranet. Powerful features let

you communicate with both audio and video, collaborate on virtually any Windows-based application, exchange graphics on

an electronic whiteboard, transfer les, use the text-based chat program, and much more. Using your PC and the Internet,

you can now hold face-to-face conversations with friends and family around the world.

To install the Microsoft® NetMeeting™:

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD ROM draw.

2. An installation wizard will automatically launch.

3. Click the “Microsoft® NetMeeting™” icon.

4. Follow the instructions presented on the screen to complete the installation.

5. You will have a choice during installation to place a desktop icon on your desktop for easy

access directly to the software.

6. For further installation details, please visit the following website:

http://www.microsoft.com/windows/netmeeting

Notes:

• You need to enter your name, your e-mail address and country details during installation.

• You need to adjust the playback volume and your record volume.

5.4 How to install Adobe® Acrobat® Reader

Adobe® Acrobat® Reader lets you view and print Adobe Portable Document format (PDF)

les on all major computer platforms, as well as ll in an submit Adobe PDF forms online.

To install the Adobe® Acrobat® Reader:

1. Reinsert the CD-ROM disc into the CD-ROM drive and close the CD ROM draw.

2. An installation wizard will automatically launch.

3. Click the “Adobe® Acrobat® Reader 4.05” icon.

4. Follow the instructions presented on the screen to complete the installation.

Visit http://www.adobe.com/ for all your FAQ’s, tips and technical support.

5.5 How to install QuickTime™ 4 Software

QuickTime™ 4 enables your computer to handle video, graphics, music, sound, sprites, text, animation and content streamed

over the internet.

To install the QuickTime™ Software:

1. Reinsert the CD-ROM disc into the CD-ROM drive and close the CD ROM draw.

2. An installation wizard will automatically launch.

3. Click the “QuickTime™” icon.

4. Follow the instructions presented on the screen.

5. Refer to your PC manual or separate modem manual for speed of your modem.

6. QuickTime will ask you to enter your name, organization and then click “Next”. No need

to enter registration number as this is a Basic version.

7. Double click on “QuickTime Player” icon to nish installation.

8. Visit http://www.apple.com/quicktime for all your FAQ’s, tips and technical support.

For Macintosh® Users:

MAC

5.6 How to Install My Camera Software

5.6.1 How to Install My Camera:

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD ROM draw.

2. Double click the CD-ROM icon “My Digital Camera”.

3. Double click the “My Camera.1” icon.

4. Click “Continue”.

5. Click “Quit” to nish the installation.

6. A folder named “My Camera” will appear in your Hard Disk after installation and a short-cut icon “My

Camera” will appear on your desktop.

Notes:

Do not select this icon as this is obsolete for this version of the camera.

5.6.2 How to Uninstall My Camera:

To uninstall the My Camera, simply remove the “My Camera” folder and the short-cut icon on the desktop.

5.7 How to Install ArcSoft® Software

MAC

5.7.1 How to Install PhotoStudio® 4.0

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD-ROM drawer.

2. Double click the CD-ROM icon “Digital Camera”.

3. Double click the “PhotoStudio® Installer” icon in English folder.

4. Follow the instructions presented on the screen to complete the installation.

5.7.2 How to Install ArcSoft Funhouse™ 1.0

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD-ROM drawer.

2. Double click the CD-ROM icon “Digital Camera”.

3. Double click the “Funhouse™ installer” icon in English folder.

4. Follow the instructions presented on the screen to complete the installation.

5.7.3 How to Install ArcSoft PhotoPrinter® 2000

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD-ROM drawer.

2. Double click the CD-ROM icon “My Digital Camera”.

3. Double click the “PhotoPrinter® 2000” icon in English folder.

4. Follow the instructions presented on the screen to complete the installation.

5.8 How to Install Adobe® Acrobat® Reader

MAC

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD ROM draw.

2. Double click the CD-ROM icon “My Digital Camera”.

3. Double click the “Acrobat® Reader” icon in English folder.

4. Follow the instructions presented on the screen to complete the installation.

5.9 How to Install QuickTime™

1. Insert the CD-ROM disc into the CD-ROM drive and close the CD ROM draw.

2. Double click the CD-ROM icon “My Digital Camera”.

3. Double click the “QuickTime™” icon in English folder.

4. Follow the instructions presented on the screen to complete the installation.

5. QuickTime will ask you to enter your name, organization and then click “Next”. No need to enter registration number as

this is a Basic version.

6. Battery Installation

The battery compartment is located on the reverse side of the G2. G2 requires 3 x AAA alkaline batteries (supplied).

To install the batteries:

1. Slide the battery cover outward and lift it upwards as shown on Diagram A and B.

2. Insert the 3 x AAA batteries. When inserting, make sure that you follow the polarity directions (+) (-) which are indicated

on the inside the battery cover and Diagram B.

3. Close and slide the battery cover inward to lock the battery door as shown on Diagram C.

Diagram A

Diagram B

Diagram C

slide the battery cover outward

lift battery cover up

insert batteries

close and slide the

cover inward

7. Getting to Know Your G2

Refer to the picture below for a quick overview for your G2.

Side View

Hole for

Wrist Strap

USB Cable

Port

Back View

Feature Button

Timer ON/OFF or

Feature Changing Button

Power ON/OFF

Smart Media Card Slot

Smart Media Card

Isolation Button

SmartMedia Card

Slot Cover

Video Out Port

LCD Display

Battery Cover

Smart Media Card Eject Button

Front View

Shutter Button

Viewnder

Lens

Flash LED

(Green)

Flash

Power LED

(Red)

7.1 LCD Display

By default, the 3 digit LCD screen displays the number of images taken. It is also used in conjunction with the Feature Button

and Feature Changing Button to access and display the G2 settings.

HIGH NORMAL LOW

PAL

NTSC

PAL

NTSC

HIGH

NORMAL

LOW

Battery Indicator

Delete All

TV Mode

Movie

Auto Flash On

Self-Timer

No. of images remaining /

LCD Messages

(details will be available under

separate sections.)

2X digital

Low Resolution

Normal Resolution

High Resolution

See Section 10.3 for LCD display quick reference guide.

7.2 Power

7.2.1 Stand-by Mode

After a period of 60 seconds inactivity, the G2 will switch to Stand-by Mode automatically and the LCD will go blank. All

images taken will not be lost as they are stored in the G2’s memory. This is a preferable way of switching your G2 off.

Waiting for the 60 seconds ensures all image processing has been completed correctly before switching off.

7.2.2 Low Battery

When your G2 has full power, the Battery indicator on the LCD display will be fully shown. When power is low, the icon will

ash. This indicates that the batteries are weak and need to be replaced.

Full Battery Power

Low Battery Power

Important Notes:

Do not remove battteries from the battery compartment when G2 is switched on.

7.2.3 SmartMedia™ Card Isolation Button

The SmartMedia™ Card Isolation Button powers down the G2 when the SmartMedia™ Card cover is opened. This is designed

to protect your G2 and SmartMedia™ card’s internal memory during insertion of your SmartMedia™ card or you can insert

another SmartMedia™ card for storage images.

Important Notes:

• Do not leave the SmartMedia™ card cover open and make sure it is closed properly otherwise G2 cannot be switched on.

• Your G2 will go to Standby Mode during insertion of your SmartMedia™ card and images taken will not be lost.

7.3 SmartMedia™ Card

Your G2 already comes with 8MB internal memory for storing images. If this is not enough memory for you, you can extend

your G2’s storage capacity up to 64MB by inserting a SmartMedia™ memory card (not included). They are available from all

good computer and camera retailers.

7.3.1 What is a SmartMedia™ Card - a brief explanation

SmartMedia™ memory cards expand your ability to store more images.

SmartMedia™ memory cards can be reused. Simply erase the data that is not needed and the SmartMedia™ card is ready

for reuse.

The SmartMedia™ card can be removed from your G2 without fear of losing the data you have stored, and additional cards

can be then be inserted. This is especially advantageous when you are away from your PC for prolonged periods of time (like

holidays) where you don’t have the facility to upload the images daily to your computer.

When a SmartMedia™ memory card is installed in the slot, the camera uses the SmartMedia™ card for all image le storage.

If images are already in the internal memory, those images will not be visible to the le system while the SmartMedia™ card

is installed. When the SmartMedia™ card is removed, images stored in the internal memory will again become accessible.

Your G2 can use SmartMedia™ Card of 16, 32 and 64MB memory sizes.

Important Notes:

• Before deciding the size of the SmartMedia™ memory card you may want to purchase, it is

advisable to understand the memory capacity of each size of SmartMedia™ card and how that

equates to the number of images each SmartMedia™ card can hold.

• Your G2 can use SmartMedia Card of 16, 32 and 64 MB memory sizes.

• Images stored on your SmartMedia™ card are an approximate calculation. Depending on the

content of the image may vary the image le size.

No. of Images for SmartMedia™

Resolution 16MB 32MB 64MB

FINE

NORMAL

ECONOMY

80 160 320

1066

2134

267

533

533 1067

1067

533

7.3.2 Volatile & Non-Volatile Memory

Your G2 comes xed with 8MB SDRam of memory (see notes below on volatile memory).

Notes:

5.5MB for image le storage only.

If your G2 has a SmartMedia™ card installed (see notes below on non-volatile memory).

Volatile Memory

Volatile memory means that the memory will be lost from your G2 if the battery runs too low, dead or if the battery is

removed. In the event that the batteries become low we recommend that you immediately upload your images to your My

Digital Camera via the USB cable (with your G2 turned on) (Also see 7.2.2).

Non-Volatile Memory

Your G2 may have a SmartMedia™ card installed. SmartMedia™ Card is a non-volatile memory which means the memory

can only be erased when following the le deletion instructions.

7.3.3 Using a SmartMedia Card (not supplied)

Notes:

Remember to switch off your G2 before inserting or ejecting a SmartMedia™ Card.

After you insert/eject a SmartMedia™ Card, ensure the card slot is closed properly. Otherwise, your G2 cannot be switched on. The card will

only enter the G2 one way.

To Insert a SmartMedia™ Memory Card:

1. Open the card slot located at the side of your G2. (Diagram A)

2. Push the memory card all the way into the card slot. (Diagram B & C) The card is designed only to t in the G2 one

way.

3. Close the card slot cover. (Diagram C) Ensuring the card cover is pushed rmly closed.

To Eject a SmartMedia™ Memory Card:

To remove the SmartMedia™ memory card, lift up the card slot cover and push the Eject Button to eject the SmartMedia™

card and then pull it out carefully. (Diagram D)

Once your G2’s memory or the inserted SmartMedia™ Card is full, upload the images to your computer and then you can

erase the images and take more images.

Diagram A

Diagram B

Lift up the card

slot cover

Push the Memory Card in

Correct insertion

Diagram C

Diagram D

Pull the card out carefully

Eject Button

8. Getting Started

8.1 Switching the G2 On

To switch your G2 on by pressing the Power ON/OFF button, which is located at the back of your G2, and 2 “beep” sounds

will be heard. Power will automatically be turned off if there are no user actions for 60 seconds. Alternatively, the power

can be turned off manually by pressing the Power ON/OFF button again. Ensure all images have been process correctly

before switching off.

When you turn the power on, the Red LED will light when your G2 is ready to take an image. If the memory is full, the Red

LED will remain on even though the Status LCD will indicate that the power is on. The LCD will display the number of images

that have been taken.

8.2 G2 Controls

Your G2 contains 4 buttons and a LCD display.

Back View

Shutter Button

Feature Button

Power ON/OFF

Feature Change &

Self-timer ON/OFF Button

HIGH

• Feature Button

Pressing the Feature Button will enter the Feature

Setting Mode and will cause only one of the LCD

Feature icons to be displayed. Pressing the Feature

Button cycles through which Feature is currently

selected. Pressing the Feature Change Button (same

as Self-Timer ON/OFF) changes the setting of the

selected feature. While in the Feature Setting Mode,

will appear on the LCD.

Pressing the Feature Button moves through the features in this sequence:

Image Setting Auto-Flash TV Format Delete All Images

Feature Mode can be exited by any of these methods:

• pressing the Feature Button again after the last feature in the sequence.

• a 10 second period with no button presses

After Feature Mode is exited, your G2 will be ready for image taking.

• Status LCD

The Status LCD contains several useful items of information. It can be used to monitor the status of

your G2 or it can be used to change your G2’s settings through use of the Feature Button.

HIGH NORMAL LOW

PAL

NTSC

Using the Feature and Feature Change Button:-

The rst feature is the Image Setting. After pressing the Feature Button, depending upon the current G2 setting, either HIGH

/ NORMAL / LOW, 2X (Digital Zoom), or

icon will be displayed. Pressing the Feature Change Button will rotate between

the various settings for the Image Quality Feature.

The HIGH / NORMAL / LOW and 2X settings are all used for capturing still images. The

icon setting is used for captur-

ing QuickTime motion movie clips.

HIGH NORMAL LOW

NTSC

Resolution

Digital Zoom

Normal

High

JEPG 70

Low

2X Diigtal Zoom

Movie

JEPG 90

Sequential 90

1280 x 960

(software enhanced)

640 x 480

320 x 240

160 x 120

640 x 480

Image Setting

Compression

Resolution (Pixels)

In Low Resolution settings, the entire image is sub-sampled down to the indicated resolution. In the 2X Digital Zoom setting

the central portion is cropped from the image, to simulate zooming in with a lens of twice the focal length.

When the Movie setting

is active, G2 will capture motion movie clips at 160 x 120 resolution, in the form of .MOV les.

Once Image Setting is at the desired choice, press the Feature Button to move to the next feature or press the Feature Button

again after the last in sequence or wait 10 seconds with no button presses for the G2 to set to image taking mode.

• Self-Timer

After exiting the Feature Setting Mode press the Feature Change/Self-Timer Button to switch between Self-Timer On or Self-

Timer Off.

To capture an image using the self-timer, press the Shutter Button to initiate the countdown. The 12-second delay is

indicated by the Power On LED (Red) ashing.

The Self-timer is automatically reset to Off after each image capture. You need to set the Self-timer on each time you want

to use it.

• Flash Mode

• Flash Off -- The Flash is disabled no matter what the ambient brightness of the surroundings are.

• Auto Flash -- Your G2 res the ash when insufcient light is measured when the shutter button is pressed.

For automatic ash, press the Feature Button twice then Feature Change Button to turn on the Auto-Flash icon on the LCD

display.

While the ash is charging, the Green LED is off. When the Green LED is permanently on, the ash is ready to re.

When the ash is turned on and the Shutter Button is pressed, the sensor reads the level of available light, and the ash is

automatically red only if there is insufcient light for good exposure without it.

When the automatic ash is turned on, it will be enabled for all subsequent images until one of the following occurs:

• Press the Shutter Button again in a light area, then the ash would not be activated.

• G2 Feature Settings are changed to capture movie clips instead of still images.

• G2 power is turned off.

8.3 Taking an Image

The G2 allows you to easily take digital image shots. This section shows you how to take images with your G2.

Images stored on your SMC card or the interal memory are an apporoximate calculation depending on the content of the

image which may vary the image le size.

To take digital image shots with your G2, make sure that there is enough battery power or that your G2 is connected to your

computer via the USB cable. If you want to use a SmartMedia™ memory card to store your images, insert the memory card

before you start taking images.

Important Notes:

Prior to taking images, make sure that G2 is not in Feature Setting Mode, as described in the previous section. Your G2 will automatically exit

from Feature Setting Mode 10 seconds after the last button press.

1. Turn your G2 on by pressing the Power Button. The Ready LED will lights up.

2. Select the resolution you want for the image. You may require auto ash to be set.

3. Using the Viewnder, focus on the object you want to capture.

4. Hold still and press the Shutter Button to take the image.

5. Wait for G2 to beep. This will conrm your image has been taken.

Important Notes:

To take a still image, press the Shutter Button. Since there may be a momentary delay between pressing the button and the actual exposure,

with

(Busy) ashing on the icon, hold your G2 steady until a “beep” is issued which indicates that the exposure is completed.

When the

(busy) on the LCD returns to image counter, you can take the next image. (The LED always remains On while

your G2 is on.)

8.4 Taking a Movie Clip

You can record movie clips in .MOV format by using your G2. This section shows you how to record a movie clip.

In Movie Mode, G2 captures QuickTime motion movie clips at 160 x 120 resolution. These video clips are stored as .MOV les,

which can be subsequently viewed on a computer using QuickTime or other .MOV compatible applications.

1. Turn your G2 on by pressing the Power Button. The Ready LED will lights up.

2. Select your G2 to Movie Mode.

3. Press and hold the Shutter Button to start recording a movie clip for as long as the button is held down, and up to a

maximum of 9 seconds. G2 will beep twice at the start of the capture of movie clip and once more at the end of the

capture of the movie clip.

Important Notes:

If G2 does not have sufcient memory space available to capture a movie, G2 will have no response when Shutter Button is pressed, or G2 will

exit the movie mode if memory is full during movie taking. You will need to either delete images from the G2 to open up free space or you will

be limited to capturing still images.

4. If the G2 has not sufcient memory space to capture a movie clip, the Movie icon will automatically

turn off, and will revert to the Normal setting for taking still images.

8.5 Erasing Contents from Your G2

When both the G2’s internal memory and the inserted SmartMedia™ card are full, it is time for you to

erase some or all of their contents to free up storage space. Before you erase anything, make sure that

you transfer the contents rst to your computer if you still want to use them.

When the Delete All Feature Mode is entered, the Delete All

icon will be on. Holding down the Feature Change Button

for at least one second while the Delete All icon is on will delete all of the stored images. Your G2 will beep to conrm that

images are being deleted, and the Delete All icon will blink. The G2 will display a

(busy) message on the LCD display

while the deletion is occurring.

9. Connecting your G2 to Your Computer

Always switch G2 on before connecting via the USB cable to your computer.

The USB cable allows you to upload images from the G2 to your PC or Mac. One end of the cable connects to the USB port

on the side of the G2 and the other end connects to your PC’s or Mac’s USB port. When your G2 is connected to your PC or

Mac, it will draw power from the PC in order to preserve your battery life.

The USB port can be found on the front or back panel of your PC or Mac. Look for this symbol next to the connection

port. (Also see your PC or Mac operating manual for the location of your USB connection port.)

USB Series “A” Plug

Connects to your PC or Mac

USB Series “A” Plug

Connects to your G2

When you rst connect your G2 to your PC, a message appears on screen saying “New Hardware Found” and “Building Driver Information Database”.

After this, you can start to upload images!

10. Uploading Images and Movie Clips to Your Computer

For Windows® Users:

10.1 Uploading Image(s) and Movie Clip(s) to Your Computer

1. Make sure your G2 is securely connected to your PC. Your G2 LCD display will display .

2. Double click the “My Digital Camera” shortcut icon on your desktop. Your images and movie clips will appear on the

computer as small thumbnails.

3. To transfer your images and/or movie clips to your computer les simply drag and drop or copy from the “My Digital

Camera” to a folder you produced earlier called “My Images”. Drag & drop all images and/or movie clips into this

folder.

• To transfer a continuous set of images, hold down the CTRL key and click on the group of images and drag and drop

the group into your folder.

4. Once the copy process is completed, the image(s) and movie clip(s) have transferred from your G2 to your PC successfully.

Double click on the folder to access the images.

Tip:

• To drag and drop, with your mouse pointer over the required image or movie clip hold down the left mouse button and drag the image or

movie clip to its desired destination. Release the mouse button to drop the image into position.

• The destination folder does not have to be opened to drag and drop. Simply drag the image over the folder and release the mouse button

to drop.

For Macintosh® Users:

MAC

10.2 Uploading Image(s) and Movie Clip(s) to Your Computer

Always switch G2 on before connecting via the USB cable to your computer.

1. Make sure your G2 is securely connected to your Mac.

2. Select the “My Camera” icon from the My Camera folder or double click the “My Camera”

shortcut icon on your desktop.

3. To transfer 1 particular image or movie clip, highlight the image or movie clip and drag

and drop from the “My Camera” to your specied folder in your hard disk.

• To transfer a continuous set of images, hold down the SHIFT key and you click on the

rst image. Then, SHIFT + Click on the last image that you want to select.

• To select multiple images, hold down the CTRL key and click on each image that you

want to select.

4. Once the copy process completed, the image(s) or movie clip(s) have transferred from your G2 to your Mac

successfully.

10.3 Viewing Images Using TV Output

Show off your images to an audience by connecting your G2 to a large-screen TV. This section shows you how to properly

connect your G2 to a TV and how to display your images.

10.3.1 Using Your G2 in TV Output Mode

Set your G2 to TV Output Mode when you want to use a TV to view the images you have taken.

10.3.2 Button Controls in TV Output Mode

NTSC

Back View

Next Image/Slide Show

Previous Image/Info Display

Power ON/OFF

Video Out Port

Important Notes:

To use the television output, plug a cable into the

Video Connector. The insertion of the cable is

automatically detected by the G2 and the display

is activated.

10.3.3 Connecting the G2 to your TV

Using the Video Out cable supplied to connect your G2 to a TV or VCR.

1. Connect one end of the Video Out Cable to the Video port on your G2.

2. Connect the other end of the cable to the video input socket normally at the back of your G2.

Selecting NTSC or PAL Video Format

Before you can view images on your TV, you need to identify rst what system your TV uses. If your TV is with NTSC system,

set your G2 to NTSC. If your TV is with PAL system, set your G2 to PAL. Refer to the Broadcasting System Table on Section

17 for international settings.

Important Notes:

When your G2 is connected to a television, the current state of the NTSC/PAL video output setting is shown in the LCD display. To switch from one

setting to the other, unplug the TV video cable from your G2, then use the Feature and Change buttons to set the desired format.

10.3.4 Viewing Your Images

After properly connecting your G2 to a TV or VCR, you can start viewing your images.

MAIN MENU

REVIEW

SLIDE SHOW

DELETE ALL

INFO

FORMAT

LANG

TIME OUT

RESTORE

SAVE

1. If you connected your G2 to a VCR using the video cable included.

2. Turn on our VCR and then switch your TV to Video channel. Remember to switch ON your G2.

After connected the G2 to a VCR or TV, the Main Menu will be displayed on the TV screen.

• Review Mode

When your G2 is connected to a TV set, all the images in the memory can be reviewed. When

main menu is displayed on the TV screen, you can select “Review” mode by using the next/

previous image button to scroll through it. Press the shutter button when the arrow lands on

the “Review” mode. Pressing the Next/Previous image buttons will scroll through the images in

memory in the order in which they were taken.

Important Notes:

If movie clips are stored in G2, each clip will be represented by the rst frame of video.

• Slide Show Mode

During image review on TV, the Slide Show Mode can be used to automatically sequence through all of the images in memory,

starting with the oldest, to the newest. To use the “Slide Show” mode, simply press next/previous image button to scroll

through the main menu until the arrow lands on the “Slide Show” mode. Press the shutter button to conrm.

• TV Info Display

Info Display shows information about your G2 on TV, including the rmware version number,

and the amount of memory in G2. This information is often useful for technical support

purpose.

To enter Info Display, press the previous/next image button until the arrow lands on the

“INFO” mode, press shutter to conrm. The Info Display will appear on the TV. Press

shutter button to return to Main Menu.

INFO

BATTERY VERY LOW

VERSION 3.000

MEMORY

USED 80KB

FREE 1440KB

SIZE 1523KB

10.4 LCD Display Quick Reference Guide

PAL

NTSC

HIGH

NORMAL

LOW

Full Battery Power

Low Battery Power

LCD Segment

Interpretation

Indication

When Lit

Indication

When Flashing

Battery Indicator

LCD Icons

TV Mode

Still Image Quality

Movie Mode

Delete All

Flash

Self-Timer

Image Counter

Sufcient power

to take image

Down to last 20% of

charge.

PAL System

European Standard

NTSC System

American Standard

See Section 17 for more

details

and international settings

High Resolution

Normal Resolution

Low Resolution

2X digital zoom

In feature setting mode, it indicates

that insufcient memory is available to

capture a movie clip.

When taking image, it indicates that

movie capture is underway.

Movie Mode is selected

Holding down the

Change Button will

delete all images

Deletion in progress

Means your camera memory is busy which is normally

displayed momentarily during taking an image or

delete images from your G2.

Flash Off (no icon)

Auto-Flash On (icon displayed)

Pressing Shutter Button

will cause 12 seconds

delay before next image.

Number of Images taken

11. How to Use Other Software

For Windows® Users:

Alternatively you can transfer your images from the folder you have produced into PhotoStudio®, PhotoFantasy™,

PhotoPrinter® and VideoImpression™. Images can also be retrieved previously saved in your computer les.

11.1 How to use PhotoStudio® 4.0

1. Go to Start > Programs > ArcSoft software Suite > PhotoStudio 4.0.

You can now start to download your stored images from your G2 by the following

steps:

2. Go to “File” and select “Open”. Select “destop” and then select “My image” folder. Select

“Open” to move an image into the PhotoStudio.

3. Go to “File” and select “Save as” and name image.

4. For further help on how to use PhotoStudio® 4.0, go to “Help” to access the Help

Topics.

Visit http://www.arcsoft.com for all your FAQ’s, tips and technical support. See Section

9 for more details.

11.2 How to use ArcSoft Funhouse™ 1.0

1. Click Start > Programs > ArcSoft Software Suite > Funhouse 1.0.

2. Click “1. Get Template” to select the template in the different type of category and then click “OK” to conrm.

Important! Make sure the “Digital Camera” CD-ROM is in the CD-ROM Drive.

Using the images stored in your G2:-

3. Double click on “2. Get Photo” and click “Open” and select the location where your images are stored.

Important! Make sure your G2 is connected to your computer.

4. The selected image will shown within the “mask” on the selected template. You can play with the image by clicking on “3.

Fine-Tune” to resize, rotate or reposition the images by reposition the image using your mouse and dragging the image.

Press “OK” to conrm.

5. Click “4. Add Text”. Type in the text your want to write and then press “OK” to conrm.

6. Click “5. Print Preview” to print a hard copy.

Using live images:-

7. You can also capture a live shot when your G2 is connected to your PC by the following steps:

8. Go to “Get Template” to select the template and then press “OK” to conrm.

Important! Make sure the “Digital Camera” CD-ROM is in the CD-ROM Drive.

9. Go to “Get Photo” and then click the “Live Video Mode” icon and the “Live” icon will ash to indicate that it is in

live mode. Click the “Capture” icon to take a live snapshot. Press “OK” to conrm.

10. For further help on how to use ArcSoft Funhouse™ 1.0, go to “Help” to access the Help Topics.

Visit http://www.arcsoft.com for all your FAQ’s, tips and technical support. See Section 7 for more details.

11.3 How to use ArcSoft PhotoPrinter® 2000

1. Select the “PhotoPrinter® 2000” icon from the “ArcSoft Camera Suite” program group on the Windows® Start Menu.

2. Choose the “Page Layout”. The selected page layout will on shown.

3. Go to “File”, select “Open”. Select “desktop” and then select “My Images” folder. Select “Open” to move an image into

the ArcSoft PhotoPrinter®.

4. The selected images will be shown on the photo library panel. Select the image you want and click “OK”.

5. The selected image will be shown on the chosen template. Click “Print” when nish placing the images.

6. For further help on how to use ArcSoft PhotoPrinter® 2000, click the “?” on the top right hand corner to access the Help

Topics.

Visit http://www.arcsoft.com for all your FAQ’s, tips and technical support. See Section 12 for more details.

Acquire

Get photo

11.4 How to use ArcSoft VideoImpression™ 1.6

Lets make a video!

Follow these basic steps to make your rst video.

Step 1 Click on new Icon.

Step 2 Using the selector button select video templates.

Step 3 Double click on the Static.avi screen in the video template selection and a copy will appear in the rst large frame

on the storyboard on the bottom.

Step 4 Double click on the small frame directly right of the large frame. A new template will appear at the top called “special

effects” Double click on the “1. Fire” special effect which will now drop into the special effect frame you highlighted.

Step 5 Double click on the next right large frame and repeat step 3 using a video template and double click template 5.

Countdown.avi. Repeat step 4.

Static.avi

1. Fire

Countdown.avi 1. Fire

Storyboard

Adding an existing video.

Step 6 To add a video you have already made double click on the next large frame in the story board to the right. Click on

the “Get” icon and select a video you had made and led in the folder called “album” click on Get, with the selector

click on the down arrow and select desktop and then double click on “Album” folder and select a le ending with .mov

(video le) the video will appear in the video templates. Double click on the video and it will appear just like other

video templates in the storyboard. Now go to step 10.

Alternatively you can produce a live video.

Ensure your G2 is connected to the computer via the USB cable. Click on the capture icon.

Step 7 And press the record icon. Wait for the video link to go live and now you’re recording, press the ESC key on

your keyboard to end the video.

Step 8 Press the “Save” icon and name your le, and then press “save”. Video impression will ask you where you want to

place your video. Select “video template”.

Step 9 Select the “album” icon and your video clip you have just produced will appear in the video templates. Double click

on your video, your video will now drop into the storyboard.

Running the video.

Step 10 Select the “play movie” icon which will assemble your video together. Press the play icon to watch your

completed video. Watch to see how the special effects merge between the frames on the story board. Now you try

to make your own and also try the audio template.

11.5 How to use Microsoft® NetMeeting™

1. Connect your G2 to the USB cable on one end.

2. Connect your USB cable to an available USB port on your PC on the other end.

3. Put your G2 next to your PC monitor or another at surface.

4. Connect your microphone (not included) to your audio card’s external microphone connector.

5. Double click the “NetMeeting” icon on the desktop or select the “NetMeeting” icon from the Windows Start Menu.

6. Type in the IP address, e-mail address, computer name or telephone number for the person you want to call and press

the “Place Call” button.

To nd your own IP address, go to “Start” and click “Run”. Type in “winipcfg” and click “OK”, IP conguration window will

appear and you can see your IP address.

7. If you need further help on how to use Microsoft® NetMeeting™, select the “Help” under the manual bar and choose the

topic you need. Or you can visit the following website:

http://www.microsoft.com/windows/netmeeting

11.6 How to use Adobe® Acrobat® Reader

1. Adobe® Acrobat® Reader enable you to view the full user’s manual in PDF format in the

G2 CD-Rom.

2. Find the user manual.pdf le on your G2 CD-Rom. Double click the le. Adobe®

Acrobat® Reader will be launched automatically.

3. If you want to review the full User’s Manual without the CD-ROM, copy the user

manual.pdf le into your Hard Disk by the following steps:

Go to Start -> Programs -> Window Explorer, then go to your CD-ROM drive, highlight

the “user manual.pdf” le and click the right button of your mouse. Select “Copy”. Go

back to you Hard Disk, click the right button and select “Paste”. The “user manual.pdf”

will be saved in your Hard Disk.

4. You can now review the full User’s Manual from your computer even without the G2 CD-

ROM inserted.

11.7 How to use QuickTime™

1. QuickTime™ enables you to view the movie clip taken by your G2.

2. Follow steps on Section 10.1 on how to upload movie clips to your computer.

3. You can now open the movie clip save in your computer using QuickTime by the following

step:

• Go to “File” and then “Open”.

• Select “desktop” and then select “My Images” folder. Highlight the wanted movie clip

and select “Open”.

For Macintosh® Users:

MAC

11.8 How to use PhotoStudio® 4.0

1. Select the “PhotoStudio® 4.0” software.

You can now start to download your stored images from your Camera:

2. Go to “File” and select the folder where you store your image and then click “open”.

3. You can now edit your image(s) with PhotoStudio’s features.

4. For further help on how to use PhotoStudio® 4.0, go to “Help” to access the Help Topics.

Visit http://www.arcsoft.com for all your FAQ’s, tips and technical support. See Section 9 for more details.

11.9 How to use ArcSoft Funhouse™ 1.0

1. Double click the “Funhouse 1.0” icon from the Funhouse™.

2. Click “1. Get Template” to select the template from the category and then click “OK” to conrm.

Important! Make sure the “Digital Camera” CD-ROM is in the CD-ROM Drive.

Using the images stored in your G2:-

3. Double click on “2. Get Photo” and click “Open”. Select the image you previously saved in your hard disk and click

“Open”.

4. The selected image will shown within the “mask” on the selected template. You can play with the image by clicking on “3.

Fine-Tune” to resize, rotate or reposition the images by reposition the image using your mouse and dragging the image.

Press “OK” to conrm.

5. Click “4. Add Text”. Type in the text your want to write and then press “OK” to conrm.

6. Click “5. Print Preview” to print a hard copy.

11.10 How to use ArcSoft PhotoPrinter® 2000

1. Double click the “PhotoPrinter®” icon from the PhotoPrinter®.

Important! Make sure the “G2” CD-ROM is in the CD-ROM Drive.

2. Choose the “Page Layout”. The selected page layout will on shown on the right panel.

3. Click “Get Photo” and then “add photo”. Find the image you want which you have already

saved in your hard disk and click “Open”.

4. The selected images will be shown on the photo library panel. Select the image you want

and click “OK”.

5. The selected image will be shown on the chosen template. Click “Print” when nish placing

the images.

6. For further help on how to use ArcSoft PhotoPrinter® 2000, click the “?” on the top right

hand corner to access the Help Topics.

Visit http://www.arcsoft.com for all your FAQ’s, tips and technical support. See Section 12

for more details.

11.12 How to use Adobe® Acrobat® Reader

1. Adobe® Acrobat® Reader enable you to view the full user’s manual in PDF format in the

G2 CD-Rom.

2. Find the user manual.pdf le on your G2 CD-Rom. Double click the le. Adobe®

Acrobat® Reader will be launched automatically.

3. If you want to review the full User’s Manual without the CD-ROM. Copy the user

manual.pdf le by dragging the “user manual.pdf’ le from CD-Rom into your Hard

Disk.

You can now review the full User’s Manual from your computer even without the G2 CD-

ROM.

11.13 How to use QuickTime™

1. QuickTime™ enables you to view the movie clip taken by your G2.

2. Follow steps on Section 10.2 on how to upload movie clips to your computer.

3. You can now open the movie clip save in your computer using QuickTime™.

12. ArcSoft® WorldWide Customer Support

For Japan For North America

ArcSoft Japan Support Center (Tokyo) ArcSoft HQ Support Center

Tel: +81-03-3834-5256 (Fremont California, CA)

Fax: +81-03-5816-4730 Tel: 1-800-762-8657 (toll free number)

Web: http://www.mds2000.co.jp/arcsoft Fax: 1-510-440-1270

E-mail: [email protected] and E-mail: [email protected]

[email protected]

For China For South & Central America

ArcSoft China Support Center (Beijing) Tel: 1-510-979-5520

Tel: 8610-6849-1368 Fax: 1-510-440-1270

Fax: 8610-6849-1367 E-mail: [email protected]

E-mail: [email protected]

For Oceania For Europe / Middle East / Africa & Rest

of the World

ArcSoft Australian Support Center ArcSoft Europe Support Center (Ireland)

(Baulkham Hills, New South Wales) Tel: +353-(0) 61-702087

Tel: 61 (2) 9899-5888 Fax: +353-(0) 61-702001

Fax: 61 (2) 9899-5728 E-mail: [email protected]

E-mail: [email protected]

Visit www.arcsoft.com or go to Start -> Programs -> ArcSoft Camera Suite -> Web Services for tips, technical support

and frequently asked questions (FAQ’s).

Customer Support

WWL UK

Unit 14, Distribution Centre.

Shannon Ind. Est.,

Shannon, Co. Clare,

Ireland

Tel : 353-61-702097

Website : www.cool-icam.com

Support email : [email protected]

13. Troubleshooting

The troubleshooting guide is designed to help you. If problems continue, please contact your local customer support hot-line.

See your registration card for helpline contact details.

For Windows® Users:

Symptom Problem Solution

Check the USB controller in your BIOS if they are

activated. If these does not work contact your

national customer support representative.

Install the software, restart your PC, and nally,

connect the G2 to the PC via the USB port, then the

software folder will appear in the Program menu.

Upload all images to your PC as soon as possible.

(please refer to Battery Guidance section in User’s

Manual.)

If you need to change batteries, and retain the

images in your G2 ’s memory, ensure you are

connected to a PC which is turned on via the USB

cable, which will then draw power from the PC whilst

you insert fresh batteries.

Upload all images to your PC or insert another

SmartMedia™ Card.

If you need to change batteries, and retain the

images in your G2’s memory, ensure you are

connected to a PC which is turned on via the USB

cable, which will then draw power from the PC whilst

you insert new batteries.

“My Camera Driver” does not load.

The installer for the Digital Camera

Manager requires the G2 be connected to

the PC (via the USB) after the software has

been installed & the PC restarted.

You have lost power to your G2 by either:

Insufcient battery power

Removing the battery without being

connected to your PC (turned on) via the

USB cable.

Your G2’s memory is full.

This means there is insufcient power to

upload images to your computer.

I receive an error message when I am

installing “My Camera Driver”

Digital Camera Manager folder is not

found in the Programs menu after I have

installed the driver.

All the images I have taken do not appear

on the G2.

The Red LED is on but not working

although I switched on my G2.

My G2 LCD displays “ ”.

Check all cables connections are secured.

* Always wait for the message to revert back to

number of images taken on your LCD.

• Always switch the G2 on rst before connecting

to the USB cable.

• Always let G2 swotch off using the auto off

function.

Connection failure or

The G2 has not completed the image

processing when you have tried to upload

the image.

I cannot upload images to the PC.

Upload saved images immediately, then replace

battery.

Battery power is too low to continue taking

images.

Battery indicator icon is blinking.

If you have any other camera installed on your

computer, remove the camera and it’s driver

completely from your system to avoid conict with

another camera or capture device.

Conict with another camera driver capture

device.

I cannot run the My Camera Driver.

Put G2 CD in CD ROM drive.No CD in CD-ROM drive.I cannot access any Funhouse’s

templates.

Go to the computer desktop. Right click on “My

Computer”. Click “Properties”. Select “Device

Manager”. Double click on “CD-ROM”, double click on

“CD-R” (normally the manufacturer’s name). Click

on “Settings”. Ensure “Auto insert notication” is

ticked and the “disconnect” is ticked. If you change

the settings the computer will ask you to restart

your PC. Click “Yes”.

The auto installation le is switched to off.

The CD ROM is disconnected.

My CD Installation wizard does not work.

Uninstall “My Digital Camera” software. Using the

different frequency setting this time.

I may have selected the wrong frequency

setting on installation.

My image quality is grainy.

Shut down all other applications and attempt to

reinstall the driver, or download the updated driver

from www.cool-icam.com and install the updated

driver.

Please also refer to the help les & User Guides that accompany the enclosed applications.

For further information and support, please visit our website: http://www.cool-icam.com

For Macintosh® Users:

MAC

Symptom Problem Solution

Shut down all other applications and attempt to

reinstall the driver, or download the updated driver

from www.coolicam.com and install the updated

driver.

Upload all images to your PC as soon as possible.

(please refer to Battery Guidance section in User’s

Manual.)

If you need to change batteries, and retain the

images in your G2 ’s memory, ensure you are

connected to a PC which is turned on via the USB

cable, which will then draw power from the PC whilst

you insert fresh batteries.

Upload all images to your PC or insert another

SmartMedia™ Card.

If you need to change batteries, and retain the

images in your G2’s memory, ensure you are

connected to a PC which is turned on via the USB

cable, which will then draw power from the PC whilst

you insert new batteries.

“Digital Camera Driver” does not load.

You have lost power to your G2 by either:

Insufcient battery power

Removing the battery without being con-

nected to your PC (turned on) via the

USB cable.

Your G2’s memory is full.

This means there is insufcient power to

upload images to your computer.

I receive an error message when I am

installing “Digital Camera Driver”

All the images I have taken do not appear

on the G2.

The Green LED is not working although I

switched on my G2.

My G2 LCD displays “ ”.

Check all cables connections are secured.

* Always wait for the message to revert back to

number of images taken on your LCD.

• Always switch the G2 on rst before connecting

to the USB cable.

• Always let G2 swotch off using the auto off

function.

Connection failure or

The G2 has not completed the image

processing when you have tried to upload

the image.

I cannot upload images to the PC.

Upload saved images immediately, then replace

battery.

Battery power is too low to continue taking

images.

Battery indicator icon is blinking.

Make sure the SmartMedia™ Card is inserted all the

way in and close the slot door properly.

The card slot door is not closed properly.I cannot switch on my G2 after inserting a

SmartMedia™ Card.

Put G2 CD in CD ROM drive.No CD in CD-ROM drive.I cannot access any Funhouse’s

templates.

Please also refer to the help les & User Guides that accompany the enclosed applications.

For further information and support, please visit our website: http://www.cool-icam.com

14. Battery Guidance

Important Notes:

We strongly recommend that you do not use rechargeable batteries as this will affect the performance of your G2.

Important Notes:

Do not remove batteries from the battery compartment when G2 is switched on.

Battery Life

• Continuous Snapshot - 3 hours (1,080 images)

• Continuous Snapshot with Flash - 30 minutes (180 images)

• Stand-by Mode - 25 days

WARNINGS!

• Batteries should be replaced by an adult.

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are to be removed from the camera before being charged (if removable).

• Rechargeable batteries are only to be charged under adult supervision (if removable).

• Different types of batteries or new and used batteries are not to be mixed.

• Only batteries of the same or equivalent type as recommended are to be used.

• Batteries are to be inserted with the correct polarity.

• Exhausted batteries are to be removed from the camera.

• The supply terminals are not to be short-circuited.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

• Do not dispose the batteries in re.

• Batteries are to be removed from the camera when not in use.

• Do not use rechargeable batteries.

These instructions should be retained for future reference.

Page is loading ...

Cool-Icam CIC-280 User manual

Brand: Cool-Icam

Model: CIC-280

Type: User manual

This manual is also suitable for

Download PDF

report

Cool-Icam CIC-280 User manual

This manual is also suitable for

Cool-Icam CIC-280 User manual

Related papers

Other documents