Safety Basement WR8800 Quick Operational Manual

Safety Basement
Brand
Safety Basement
Model
WR8800
Type
Quick Operational Manual
www.safetybasement.com
Quick Operational Guide – ITEM# WR8800
Thanks for purchasing this unique camera recorder. This unit has incredible features:
1. Video Recording (with audio)
2. Voice recording (audio only recording) at 128 Kbps.
3. Camera function for picture taking.
4. Infra red LEDs for night recording
5. PC camera
www.safetybasement.com
TURNING UNIT ON/STANDBY MODE
1. This unit was made to start recording video a few seconds after being turned on. So if you want it to
start recording video right away then turn it on and let it begin. However since this unit has other
features such as voice recording and camera, then you may not want it to start recording video right
after being turned on. See instructions below on how to get it to standby mode:
GETTING TO STANDBY MODE:
1. firmly press ON/OFF button for about two seconds and release. The BLUE indicator light will turn on
and after about 3 seconds it will start to blink. Quickly (and firmly) press the same (ON/OFF) button and
release. The blue light will stop blinking and stay at a steady blue. You are now in standby mode!
TURNING UNIT OFF:
1. To turn unit off at any point simply press and hold the ON/OFF button for about 5 seconds and
release. The indicator lights will briefly turn on then off.
2. If this unit is not used for about 1minutes, unit will turn itself off.
AUDIO RECORDING:
1. To get to audio mode, get unit to standby mode. See instructions above.
2. Then press the MODE button quickly (and firmly) and a RED indicator light will turn on. Once you see
the steady red light press the button again quickly (and firmly). You will now get a steady BLUE/RED light
(although it looks more like blue than both)This should get you in audio mode. Essentially you pressed
the mode button TWICE, slowly. RED LIGHT THE FIRST PRESS THEN BLUE LIGHT THE SECOND PRESS.
3. Now quickly and firmly press the ON/OFF button and release. The blue light will start blinking slowly.
You are now in audio recording mode. (blue light will blink while in audio recording mode)
4. To stop audio recording, just firmly press and release the same ON/OFF button
www.safetybasement.com
VIDEO MODE:
TURNING ON INFRA RED LAMPS:
This watch camera has infra-red capability. Turn them on and it allows your video to record in the dark.
1. Turn your watch on and get it to standby mode (see instructions at top)
2. Once in standby mode (steady blue) press and hold MODE button and notice that a small red light
inside the blue steady light will blink three times. Release the MODE button after the third blink. This
means the infra-red lamps have now been turned on. You will not notice the infra red lamps with the
naked eye. They are invisible. So make sure you notice the inside red light blink three times! Now you
can start your video recording in the dark and you should be able to capture good night video!
3. To record video after turning on infrared lamps, just quickly press the ON/OFF button. The blue light
will blink three times and go off. You are now recording video with infra red lamps turned on!
4. To stop video recording, firmly press the ON/OFF button TWICE. You should get a steady blue after
that.
VIDEO RECORDING:
1. To record video just press ON/OFF button for about two seconds and release. Blue light will stay
steady for about 3 seconds then blink 3 times and go off. You are now recording video.
2. To stop video recording simply press the ON/OFF button twice (firmly) and the blue light will return to
steady mode.
CAMERA MODE:
1. To get to camera turn unit on and get it to standby mode. (see first instructions)
2. Now press the MODE button firmly (once). You should get a steady red indicator light. You are now in
CAMERA MODE
3. To take a picture press the ON/OFF button once. The red light will blink once and return to steady red.
Repeat as necessary.
www.safetybasement.com
IMPORTANT: If at any point you get confused as to which mode you are in, just turn the unit off
(by pressing and holding the ON/OFF button for about 5 seconds and releasing. You will have turned
unit off.) Then start the process from the beginning so that you are sure which function you are in. This
is a simple short cut for you.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Safety Basement WR8800 Quick Operational Manual

Safety Basement
Brand
Safety Basement
Model
WR8800
Type
Quick Operational Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents