Hobart 2912PS Assembly Instructions

Type
Assembly Instructions
PL-41105-1
FOOD CHUTE
MODEL 2612
HANGERS
REAR HEAVY
MEAT GRIP
REAR MEAT GRIP
SLIDE ROD
IN FRONT POSITION
Fig. 3
ASSEMBLY INSTRUCTIONS
FOOD CHUTE — KIT NO. 873604
Use this kit for any of the following Hobart slicer models: 1612, 1612P, 1612E, 1712, 1712E, 1712R,
1712RE, 1812, 1812PS, 1812RS, 1912, 1912R, 2612, 2612C, 2712, 2712C, 2812, 2812C, 2812PS,
2912, 2912B, 2912C, 2912PS, 2912SC.
PART NO. NAME OF PART AMT.
873604 Food Chute Kit (complete) .....................................................1
Chute & Hangers ........................................................................
1
Pusher Plate & Handle ...............................................................
1
F-33999 Assembly Instructions ................................................................
1
ASSEMBLY
Slicers with Front Meat Grip
WARNING: TURN SLICER OFF BEFORE ASSEMBLING FOOD CHUTE.
1. Position the Food Chute so the hangers fit around the Front Meat Grip Slide Rod (Figs. 1, 2). Rotate
Food Chute Hangers around the Slide Rod, lowering the Food Chute onto the Carriage Tray.
The Pusher Plate is used to push food down inside the Food Chute during slicing.
Fig. 1 Fig. 2
Slicers with Rear Meat Grip
WARNING
:
TURN SLICER OFF BEFORE ASSEMBLING
FOOD CHUTE.
For models 2612, 2612C, 2712, 2712C, 2812, 2812C,
2812PS, 2912, 2912B, 2912C, 2912PS, 2912SC when
equipped with accessory Rear Meat Grip only.
Assemble the Food Chute to the Slide Rod in the front
Slide Rod location, as shown (Fig. 3).
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
FORM 33999 Rev. A (06-06)
PL-41103-1
FOOD CHUTE
FRONT MEAT GRIP
SLIDE ROD
MODEL 1712E
HANGERS
FRONT MEAT GRIP
PL-41104-1
FOOD CHUTE
MODEL 2612
HANGERS
FRONT MEAT GRIP
FRONT MEAT GRIP
SLIDE ROD
– 2 –
Slicers with Feed-Screw Mechanism
For models 1712R, 1712RE, 1912R only.
WARNING: TURN SLICER OFF BEFORE ASSEMBLING FOOD CHUTE.
1. Turn the Knurled Knob on the Adjusting Screw
clockwise to move the Actuating Block all the
way to the front (Fig. 4).
2. Assemble the Food Chute so the first Hanger
fits around the Front Meat Grip Slide Rod
(Fig. 5). Slide the Food Chute and first
Hanger down the Front Meat Grip Slide Rod
and fit the second Hanger around the Rod.
With both Food Chute Hangers in place around
the Slide Rod, lower the Food Chute to the
Carriage Tray.
3. Turn the Prongs of the Meat Grip toward the
Food Chute. Position the Pin on the Plunger
Knob shaft in the slot on the Plunger Housing
with the Meat Grip positioned at the top of the
Feed Screw (Fig. 6).
FORM 33999 Rev. A (06-06) PRINTED IN U.S.A.
Fig. 4
Fig. 5
Fig. 6
PL-41132-1
ACTUATING BLOCK
ADJUSTING SCREW
KNURLED KNOB
PL-41133-1
HANGER
FRONT MEAT GRIP
SLIDE ROD
FOOD CHUTE
PL-41134-1
FOOD CHUTE
PLUNGER KNOB
FEED SCREW
PIN IN SLOT
PLUNGER HOUSING
MEA
T GRIP PR
ONGS
  • Page 1 1
  • Page 2 2

Hobart 2912PS Assembly Instructions

Type
Assembly Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI