Hobart 1612 Assembly Instructions

Brand: Hobart

Model: 1612

Type: Assembly Instructions

PL-41105-1

FOOD CHUTE

MODEL 2612

HANGERS

REAR HEAVY

MEAT GRIP

REAR MEAT GRIP

SLIDE ROD

IN FRONT POSITION

Fig. 3

ASSEMBLY INSTRUCTIONS

FOOD CHUTE — KIT NO. 873604

Use this kit for any of the following Hobart slicer models: 1612, 1612P, 1612E, 1712, 1712E, 1712R,

1712RE, 1812, 1812PS, 1812RS, 1912, 1912R, 2612, 2612C, 2712, 2712C, 2812, 2812C, 2812PS,

2912, 2912B, 2912C, 2912PS, 2912SC.

PART NO. NAME OF PART AMT.

873604 Food Chute Kit (complete) .....................................................1

Chute & Hangers ........................................................................

Pusher Plate & Handle ...............................................................

F-33999 Assembly Instructions ................................................................

ASSEMBLY

Slicers with Front Meat Grip

WARNING: TURN SLICER OFF BEFORE ASSEMBLING FOOD CHUTE.

1. Position the Food Chute so the hangers ﬁt around the Front Meat Grip Slide Rod (Figs. 1, 2). Rotate

Food Chute Hangers around the Slide Rod, lowering the Food Chute onto the Carriage Tray.

The Pusher Plate is used to push food down inside the Food Chute during slicing.

Fig. 1 Fig. 2

Slicers with Rear Meat Grip

WARNING

TURN SLICER OFF BEFORE ASSEMBLING

FOOD CHUTE.

For models 2612, 2612C, 2712, 2712C, 2812, 2812C,

2812PS, 2912, 2912B, 2912C, 2912PS, 2912SC when

equipped with accessory Rear Meat Grip only.

Assemble the Food Chute to the Slide Rod in the front

Slide Rod location, as shown (Fig. 3).

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

FORM 33999 Rev. A (06-06)

PL-41103-1

FOOD CHUTE

FRONT MEAT GRIP

SLIDE ROD

MODEL 1712E

HANGERS

FRONT MEAT GRIP

PL-41104-1

FOOD CHUTE

MODEL 2612

HANGERS

FRONT MEAT GRIP

SLIDE ROD

– 2 –

Slicers with Feed-Screw Mechanism

For models 1712R, 1712RE, 1912R only.

WARNING: TURN SLICER OFF BEFORE ASSEMBLING FOOD CHUTE.

1. Turn the Knurled Knob on the Adjusting Screw

clockwise to move the Actuating Block all the

way to the front (Fig. 4).

2. Assemble the Food Chute so the ﬁrst Hanger

ﬁts around the Front Meat Grip Slide Rod

(Fig. 5). Slide the Food Chute and first

Hanger down the Front Meat Grip Slide Rod

and ﬁt the second Hanger around the Rod.

With both Food Chute Hangers in place around

the Slide Rod, lower the Food Chute to the

Carriage Tray.

3. Turn the Prongs of the Meat Grip toward the

Food Chute. Position the Pin on the Plunger

Knob shaft in the slot on the Plunger Housing

with the Meat Grip positioned at the top of the

Feed Screw (Fig. 6).

FORM 33999 Rev. A (06-06) PRINTED IN U.S.A.

Fig. 4

Fig. 5

Fig. 6

PL-41132-1

ACTUATING BLOCK

ADJUSTING SCREW

KNURLED KNOB

PL-41133-1

HANGER

FRONT MEAT GRIP

SLIDE ROD

FOOD CHUTE

PL-41134-1

FOOD CHUTE

PLUNGER KNOB

FEED SCREW

PIN IN SLOT

PLUNGER HOUSING

MEA

T GRIP PR

ONGS

Hobart 1612 Assembly Instructions

Hobart 1612 Assembly Instructions

Hobart 1612 Assembly Instructions

Related papers

Other documents