Speakman S-3015 Dimensions Guide

Type
Dimensions Guide
THIS SPACE FOR ARCHITECT/ENGINEER APPROVAL.
400 ANCHOR MILL ROAD | NEW CASTLE, DE 19720
P: 800-537-2107 | F: 800-977-2747
WWW.SPEAKMANCOMPANY.COM
REVISION DATE: JANUARY 2014
SPECIFICATION
29
Management Systems
Registered to ISO 9001
SEE REVERSE FOR ROUGH-IN DIMENSIONS
SPEAKMAN
®
RetroShowerhead
FEATURES:
• 1920s Speakman showerhead inspired design
• 4 in. diameter face
• 8 jets with 64 spray channels
• Spray adjusting handle
• Solid brass construction
• 2.5 gpm (9.5 L/min) ow rate
COMPLIANCE:
• ASME A112.18.1/CSA B125.1 certied
FINISH:
• Polished Chrome (standard)
WARRANTY:
• Lifetime Limited Warranty
S-3015
THIS SPACE FOR ARCHITECT/ENGINEER APPROVAL.
400 ANCHOR MILL ROAD | NEW CASTLE, DE 19720
P: 800-537-2107 | F: 800-977-2747
WWW.SPEAKMANCOMPANY.COM
REVISION DATE: JANUARY 2014
SPECIFICATION
30
NOTE: 1. All dimensions are in inches (millimeters) unless otherwise specified and are
subject to change without notice.
Management Systems
Registered to ISO 9001
07/18
92-3275
SPEAKMAN COMPANY
S-3015, S-3019 Installation, Maintenance & Operation Instructions
ANYSTREAM
®
SHOWERHEAD
DESCRIPTION
Polished chrome plated ANYSTREAM showerhead. Brass ball swivel joint. Brass shank. Spray adjusting
P-nut handle. 3-1/2” face. 8 Lexan deposit resisting plungers with 64 spray channels. Water conserving pressure
compensating AUTOFLO® device reduces flow to 2.5 GPM/9.46LPM maximum, to meet existing ANSI A112.18.1M
Standard. ½” NPT inlet.
SPECIFICATIONS SUPPLY INLET: ½” NPTF, FLOW RATE: 2.5 GPM/ 9.46LPM, WEIGHT: 2.43 LBS.
For use with automatic compensating valves rated at 2.30Gpm / 8.71Lpm or less at 45psi.
INSTALLATION
Apply pipe thread tape in a clockwise direction to threads of shower arm. Pipe joint compound may be used instead
of tape. Turning in a clockwise direction, thread the showerhead on to the shower arm. Tighten with a pipe wrench
or a pair of pliers. Position the showerhead by rotating it clockwise. Make sure the ball joint coupling nut is properly
tightened. Turn the water supply on and check for leaks. Check all threaded connection periodically to make sure
they are tight.
OPERATION
To adjust the spray pattern, simply rotate the handle to the desired spray (needle spray, gentle rain or full flood).
MAINTENANCE
Product improvements may cause
specification and dimensional
changes without notice.
Periodic cleaning, using mild soap and warm water, will help keep your SPEAKMAN ANYSTREAM® showerhead’s
appearance in its original condition. For best results, dry immediately with a soft, clean cloth.
Caution: Do not use harsh and/or abrasive cleaners on showerheads.
In certain water conditions, mineral deposits may form. To keep your showerhead like new we recommend soaking
the showerhead in 2 parts white vinegar and 1 part water for about 1 hour or more, depending on the amount of
buildu
p
. Rinse thorou
g
hl
y
. Brush off an
y
remainin
g
mineral de
p
osits if necessar
y
.
SPEAKMAN
®
PO Box 191 Wilmington, DE 19899 Phone: 800-537-2107 Fax: 800-977-2747
Visit us on the web at www.speakmancompany.com
ROUGH-IN MEASUREMENTS
S-3015 Round Shank
S-3019 Octagon Shank
SPEAKMAN
®
RetroShowerhead S-3015
  • Page 1 1
  • Page 2 2

Speakman S-3015 Dimensions Guide

Type
Dimensions Guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages