Home Styles 5554-831 Operating instructions

Type
Operating instructions
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
88 5552 83
Biscayne Chaise
Head Cap Bolt (large)
6 pcs.(+1 extra)
Head Cap Bolt (round head)
2 pcs.(+1 extra)
Key Wrench
1 pc.
Key Wrench (large)
1 pc.
Bolt
6 pcs.(+1 extra)
Flat Washer (middle)
6 pcs.(+1 extra)
Flat Washer (small)
2 pcs.(+1 extra)
Flat Washer (large)
2 pcs.(+1 extra)
Spring Washer (middle)
6 pcs.(+1 extra)
Spring Washer (small)
2 pcs.(+1 extra)
Spring Washer (large)
2pcs.(+1 extra)
Nut (middle)
6 pcs.(+1 extra)
Nut (small)
2 pcs.(+1 extra)
Nut (large)
2 pcs.(+1 extra)
Nut Cap
6 pcs.(+1 extra)
Wheel Bolt
2 pcs.(+1 extra)
A.
Seat
1 pc.
B.
Arm
1 pc.
C.
Arm
1 pc.
D.
Back Frame
1 pc.
E.
Support
1 pc.
G.
Wheel
2 pcs.
F.
Leg
2 pcs.
Tools required for assembly : Slotted screwdriver
Part List
Hardware List
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Small
Hex Wrench
1 pc.
Large
Hex Wrench
1 pc.
Figure 1
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Key Wrenches and Hex Wrench in a safe place as you may need to tighten up the Nuts and Head Cap Bolts
in the future.
* Use a soft cloth between the parts and the floor.
Figure 2
Insert all Bolts into the
pre-drilled holes of Seat (A). (See Figure1)
Attach Legs (F) onto Seat (A) with
Flat Washers (middle), Spring Washers (middle),
Nuts (middle) and Nut Caps.
STEP 1
Attach Arms (B) and (C) to
unit with Head Cap Bolts (large).
Attach Wheels (F) to unit with
Flat Washers (large),
Spring Washers (large) and Nuts (large).
(See Figure 2)
STEP 2
Nut Cap
Nut (large)
Wheel Bolt
Nut (middle)
Flat Washer (large)
Flat
Washer (middle)
Spring Washer (large)
Spring
Washer (middle)
B
A
Assembly Instructions 2/3
F
F
A
C
G
G
Head Cap Bolt (large)
Large Key Wrench
Nut (large)
Spring Washer (large)
Flat Washer (large)
Wheel Bolt
Plastic Ring is on
outside of wheel
Assembly Instructions 3/3
STEP 3
Turn the unit to its’ upright position.
Place Back Frame (D) into position with Head Cap Bolts (large).
Attach Support (E) to Back Frame (D) with Head Cap Bolts
(round head), Flat Washers (small), Spring Washers (small) and Nuts.
(See Figure 3)
Nut (small)
Nut (small)
Flat Washer (small)
Flat Washer (small)
Head Cap Bolt (round head)
Head Cap Bolt
(round head)
Spring Washer (small)
Spring Washer (small)
Figure 3
Head Cap Bolt (large)
D
E
  • Page 1 1
  • Page 2 2
  • Page 3 3

Home Styles 5554-831 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI