Regency Fireplace Products CitySeries Chicago Corner 40RE Power Vent Owner's manual

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

City Series

®

Direct Vent Gas Power Vent Fireplace

Owners &

Installation Manual

STYLE MODEL

Left Corner CC40LEPV-NG / CC40LEPV-LP

Right Corner CC40REPV-NG / CC40REPV-LP

Tested by:

www.regency-re.com

- Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

- Installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.

Warning

Fire or explosion Hazard

Failure to follow safety warnings exactly could result in serious

injury, death, or property damage.

919-925d

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

04.09.20

Certiﬁed to/Certiﬁé pour: CSA 2.17-2017

ANSI Z21.88-2017

CSA 2.33-2017

2 | City Series CC40EPV

This appliance may be installed in an aftermarket, permanently lo-

cated, manufactured home (USA only) or mobile home, where not

prohibited by local codes.

This appliance is only for use with the type of gas indicated on the

rating plate. This appliance is not convertible fore use with other

gases, unless a certiﬁed kit is used.

To the New Owner:

Congratulations!

You are the owner of a state-of-the-art Gas Fireplace by REGENCY

®

. The City Series are hand crafted appliances and

have been designed to provide you with all the warmth and charm of a wood ﬁreplace at the ﬂick of a switch. The CC40LE

/CC40RE City Series have been approved by Intertek for both safety and efﬁciency. As it also bears our own mark, it

promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment

now to acquaint yourself with these instructions and the many features of your Regency

®

Fireplace.

City Series CC40EPV | 3

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency

®

product has been tested and listed by Warnock Hersey/Intertek as a Direct Vent Wall Furnace to the following standards:

VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2017 / CSA 2.33-2017 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES

CSA 2.17-2017.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home

Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes

follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the

current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This Regency

®

mobile/manufactured home listed appliance comes factory equipped with four 1/4" diameter holes located near each corner

of the base. Fasten the ﬁreplace in place using screw, inserted through the holes.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local

codes. See the "Wiring Diagram" section.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

This appliance may only be installed in an aftermarket permanently located, manufactured home (U.S.A only) or mobile home, where not

prohibited by local codes.

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases,

unless a certiﬁed kit is used.

Ensure that structural members are not cut or weakened during installation.

4 | City Series CC40EPV

table of contents

Gas Power Vent Installation - Framing

-Inline Power Vent Terminations .................................51

Power Vent Terminal Installation - Inline Power Vent

Terminations ..............................................................52

Gas Power Vent Installation Clearance Requirements

Inline Power Vent Terminations ....................................53

Unit Installation with Horizontal Termination - End of

Line Power Vent-4" x 6-5/8" Rigid Venting .................54

Unit Installation with Horizontal Termination - End of

Line Power Vent-4" x 6-5/8" Flex Venting ...................55

Verical Inline Power Vent Terminations - Rigid Pipe ....56

Verical Inline Power Vent Terminations - Flex Pipe ......57

Vertical Flue Extension Kit-Horizontal Power Vent Kit . 59

Ceiling Firestop / Firestop Spacer ...............................60

Gas Power Vent Installation - Wiring Power Vent to Unit 6 1

Gas Power Vent Install -Wiring End of Line Power Vent 6 2

Gas Power Vent Installation - Wiring Power Vent to Unit 6 4

System Data ................................................................67

High Elevation ..............................................................67

Gas Line Installation ....................................................67

Pilot Adjustment ...........................................................67

Gas Pipe Pressure Testing ..........................................67

885 S.I.T. Valve Description .........................................67

Wiring Diagram ............................................................68

Inner Glass Panel (Firebox Glass) Install/Removal .....69

Outer Safety Glass Panel (Barrier Glass) Install/Removal

.....................................................................................71

LP Conversion Instructions ..........................................73

CC40LE/CC40RE Painted Panel Installation ..............75

Inner Panels - CC40LE/CC40RE.................................75

Outer Panels - CC40LE/CC40RE ................................75

CC40LE/CC40RE Glass Panel Installation .................76

CC40LE/CC40RE Enamel Panel Installation ..............78

Burner and Firebox Media Options ..............................80

Optional Driftwood Log Set Installation .......................81

Optional Birchwood Log Set Installation ......................83

Optional Splitwood Log Set Installation .......................85

CC40LE/CC40RE - Removable Drywall Guides .........87

First Fire ......................................................................88

Normal Operating Sounds of Gas Appliances .............88

Aeration Adjustment ....................................................88

Bulb Replacement .......................................................89

Valve Replacement ......................................................90

Power Vent Maintenance-End of Line Power Vent

-External Power Vent Access .....................................91

Internal Power Vent Access .........................................92

Power Vent Maintenance-External Power Vent

Access-Inline Power Vent ..........................................93

CC40LE Main Assembly ..............................................94

CC40RE Main Assembly .............................................96

Power Vent - End of Line .............................................98

Power Vent Inline .........................................................99

Warranty ............................................................100-104

Copy of Safety Decal .....................................................5

Important Message ......................................................8

Before You Start .............................................................8

Owner's Information

Installer's Information

General Safety Information ............................................9

Lighting Procedure ......................................................10

Shutdown Procedure ...................................................10

Copy of the Lighting Plate Instructions ........................11

Proﬂame II Remote Control Operating Instructions .....12

Inner Glass Panel (Firebox Glass) Installation ............16

Outer Safety Glass Panel (Barrier Glass) Installation . 18

Maintenance Instructions ............................................20

Log Replacement ........................................................20

Glass Gasket ...............................................................20

Glass ...........................................................................20

Glass Replacement .....................................................20

Warranty ............................................................100-104

Locating Your Gas Fireplace ........................................22

Unit Assembly Prior to Installation ...............................22

Installation Checklist ....................................................23

Heatwave Duct System ...............................................23

Clearances CC40LE/CC40RE .....................................25

Clearances CC40LE/CC40RE .....................................26

Clearances CC40LE/CC40RE .....................................27

Mantel Clearances CC40LE/CC40RE .........................28

Framing Dimensions CC40LE (Left Corner) ................29

Framing Dimensions CC40RE (Right corner) .............30

Wall Board/Drywall Installation CC40LE/CC40RE ......31

Framing & Finishing Inset Install CC40LE/CC40RE ....32

Optional Framing Kit Installation CC40LE/CC40RE ....33

Building additional Framing Off of the Framing Kit ......36

TV Recessed into Wall - Typical Installs ......................37

Maximum TV Recess ...................................................37

TV Flush with Hearth ...................................................37

Wall Mount On / Off Switch Installation .......................38

Exterior Vent Termination Locations ............................39

4"x 6-5/8" Rigid Pipe - Cross Reference Chart ............40

Venting Arrangements for Horizontal Terminations

- End of Line Horizontal Vent Chart ...........................42

Vent Restrictor Position ...............................................42

Venting Arrangements for Horizontal Terminations

- Inline Horizontal Vent Chart .....................................43

Venting Arrangement for Vertical Terminations

-Inline Power Vent ......................................................44

Vertical Inline Power Vent Terminations - Rigid Pipe ...45

Venting Arrangements Vertical Terminations-Flex Pipe 46

Horizontal Terminations-Inline Power Vent

-4" x 6-5/8" Flex Vent .................................................47

Horizontal Terminations-Inline Power Vent

-4" x 6-5/8" Rigid Pipe ...............................................48

Horizontal Terminations-End of Line Power Vent

-4" x 6-5/8" Rigid Pipe ...............................................49

End of Line Power Vent Dimensions ............................50

City Series CC40EPV | 5

safety decal

This is a copy of the label that accompanies Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. The safety label is located

on the front inside base of the unit, visible when the outer front panel is removed.

NOTE: Regency

®

units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

Copy of Safety Decal

For the State of Massachusetts, installation

and repair must be done by a plumber or

gas ﬁtter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, ﬂexible con-

nectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appli-

ances individual manual shut-off must be a

t-handle type valve.

The State of Massachusetts requires the

installation of a carbon monoxide alarm in

accordance with NFPA 720 and a CO alarm

with battery back up in the same room where

the gas appliance is installed.

Part #: 919-919a

Colour: Black on grey except what is indicated as being printed red.

Size: (File at 100%) 9.3"w x 5.7"h

Material:

Start serial sequence @ 477000001

Oct. 10/18: Created draft

Nov.21/18: Added efficiencies as per R/D

Jan. 29/19: Remodeled decal + added ETL logo at the bottom

DO NOT REMOVE THIS LABEL /

NE PAS ENLEVER CETTE ÉTIQUETTE

477

DOOR SEAL: Please

check that the door is

properly sealed

FPI Fireplace Products International Ltd. Delta, BC, Canada

Minimum Clearances to Combustibles /

Dégagements minimaux par rapport aux matériaux combustibles

Serial No./ No de série

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.

Listed/Nom: VENTED GAS FIREPLACE / FOYER AU GAZ À ÉVACUATION

Certified to/Certifi : é

ANSI Z21.88-2017 • CSA-2.33-2017

CSA 2.17-2017

Electrical supply / Alimentation électrique 115VAC, 1.5 A, 60Hz.

Made in Canada/ Fabriqué au Canada

Duplicate S/N

(See instruction manual for detailed instructions)

(Voir manuel pour plus de détails)

GAZ PROPANE : Modèle

CC40LEPV-LP/CC40REPV-LP

PROPANE GAS: Model:

CC40LEPV-LP/CC40REPV-LP

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

GAZ NATUREL : Modèle CC40LEPV-NG/CC40REPV-NG

5.0" WC/C.E. (1.25 kPa)

3.8" WC/C.E. (0.94 kPa)

1.1" WC/C.E. (0.27 kPa)

# 42 DMS

28,500 Btu/h (8.33 kW)

15,500 Btu/h (4.54 kW)

0-4500 ft/pi (0-1372 m)

11" WC (2.73 kpa)

10.5 " WC/C.E. (2.62 kPa)

2.9" WC/C.E. (0.72 kPa)

# 53 DMS

28,500 Btu/h (8.35kW)

15,500 Btu/h (4.54 kW)

0-4500 ft/pi (0-1372 m)

Minimum supply pressure

Manifold pressure - High

Manifold pressure - Low

Orifice size

Maximum input

Minimum input

Altitude

Side Walls / Murs latéraux

A 36” (914 mm)

Ceiling / Plafond

B 37-1/2” (953 mm)

Min. Mantel Height /Hteur Min

Manteau

C 9" (229 mm)

Max. Mantel Depth/Profondeur Max

Manteau

D 12” (305 mm)

Alcove Width/Largeur Alcôve

E 84" (1524 mm)

Alcove Depth/Profondeur Alcôve

F 36" (2134 mm)

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.

This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the

United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles

This appliance is only for use with the type(s) of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by

local codes. See owner's manual for details. This appliance is supplied with a conversion kit.

L'appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation National Fuel Gas Code ANSI Z223.1, ou CSA-B149.1 Natural Gas and

Propane Installation Code en vigueur.

L'appareil doit être installé conformément à la norme CAN/CSA-Z240, Série MM, Maisons mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction

and Safety Standard. Si ces normes ne sont pas applicables, veuillez vous référer à la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C

Standard for Recreational Vehicles.

Cet appareil doit être utilisé uniquement avec les types de gaz indiqués sur la plaque signalétique et peut être installé dans une maison préfabriquée (É.-U. seulement) ou mobile installée à demeure si les règlements

For Use Only with Barrier CC40LEPV - Left Corner (Part # 940-485/P,940-440/P) & CC40REPV Right Corner (Part # 940-485/P,940-439/P) Follow installation instructions.

Utiliser uniquement avec l’écran CC40LEPV -Coin gauche (n°940-485/P,940-440/P) & CC40REPV - Coin droit (n°940-485/P,940-439/P) . Suivre les instructions d'installation.

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) -

Basse

Taille de l’orifice

D bit calorifique maximal é

D bit calorifique minimalé

Altitude

Pression d'alimentation minimale

Pression de sortie (manifold) - Haute

Pression de sortie (manifold) - Basse

Taille de l’orifice

D bit calorifique maximalé

D bit calorifique minimalé

Altitude

VENTED GAS FIREPLACE - NOT FOR USE WITH SOLID FUELS.

NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE. FOYER AU GAZ À ÉVACUATION -

Part No. 946-556 Heatwave Kit may be used. La trousse Heatwave (pièce n°946-556) peut être utilisée.

Model/Modèle :

CC40LEPV-NG

CC40LEPV-LP CC40REPV-NG CC40REPV-LP

FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY À UTILISER AVEC LES PORTES VITRÉES HOMOLOGUÉES POUR L'APPAREIL

C #: 4001172

Refer to Intertek's Directory of Building Products for detailed information.

Pour plus de détails, se reporter au Répertoire des produits de construction de Intertek.

J

B

C

D

H

A

E

F

919-919a

CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1

Natural Gas / Gaz naturel 60.02%

Propane Gas / Gaz propane 60.85%

CANADIAN ENERGY

PERFORMANCE

VERIFIED

RENDEMENT

ÉNERGÉTIQUE

VÉRIFIÉ

EP5011169

NATURAL GAS: Model: CC40LEPV-NG/CC40REPV-NG

Decal Location

Remove barrier glass from unit (refer to manual)

lift out the outer liner base glass once the glass

has been removed the rating plate will be attached

to a small black chain as seen below.

DO NOT REMOVE DECAL FROM UNIT

6 | City Series CC40EPV

dimensions

25

1

4

"

643mm

33

3

16

"

842mm

37

1

8

"

943mm

42

7

8

"

1089mm

43

5

8

"

1109mm

10

1

4

"

261mm

15

1

16

"

382mm

7

8

"

200mm

14

3

4

"

375mm

34

3

8

"

873mm

18

11

16

"

475mm

17

5

8

"

449mm

6

3

4

"

172mm

4"

102mm

48"

1219mm

23

1

8

"

587mm

24

1

4

"

616mm

47

3

8

"

1203mm

Note: Height Dimension may vary depending on the height of the leveling legs.

CC40LE (Left Corner) Dimensions

Dimensions will appear as (inches)" / (metric)mm

throughout this manual. The inches are rounded to the

nearest 1/16" when converted, when greater accuracy

is required, use the metric dimensions.

Note: These units are non-load bearing.

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.

ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

City Series CC40EPV | 7

dimensions

43"

1091mm

25

1

4

"

643mm

33

3

16

"

842mm

37

1

8

"

943mm

43

5

8

"

1108mm

7

8

"

200mm

15

1

16

"

382mm

10

1

4

"

262mm

14

3

4

"

374mm

34

3

8

"

873mm

17

5

8

"

448mm

18

11

16

"

475mm

6

3

4

"

172mm

4"

102mm

11

7

16

"

290mm

7

1

4

"

184mm

23

1

8

"

587mm

24

1

4

"

616mm

47

3

8

"

1203mm

CC40RE (Right Corner) Dimensions

Note: Height Dimension may vary depending on the height of the leveling legs.

Dimensions will appear as (inches)" / (metric)mm

throughout this manual. The inches are rounded to the

nearest 1/16" when converted, when greater accuracy

is required, use the metric dimensions.

Note: These units are non-load bearing.

8 | City Series CC40EPV

owner's information

CLOTHING OR OTHER FLAMMABLE

MATERIAL SHOULD NOT BE PLACED

ON OR NEAR THE APPLIANCE.

CHILDREN AND ADULTS SHOULD BE

ALERTED TO THE HAZARDS OF HIGH

SURFACE TEMPERATURES, ESPE-

CIALLY THE FIREPLACE GLASS, AND

SHOULD STAY AWAY TO AVOID BURNS

OR CLOTHING IGNITION.

INSTALLATION AND REPAIR SHOULD

BE DONE BY AN AUTHORIZED

SERVICE PERSON. THE APPLIANCE

SHOULD BE INSPECTED BEFORE

USE AND AT LEAST ANNUALLY BY A

PROFESSIONAL SERVICE PERSON.

MORE FREQUENT CLEANING MAY

BE REQUIRED DUE TO EXCESSIVE

LINT FROM CARPETING, BEDDING

MATERIAL, ETC. IT IS IMPERATIVE THAT

CONTROL COMPARTMENTS, BURNERS

AND CIRCULATING AIR PASSAGEWAYS

OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE

APPLIANCE SHOULD BE LOCATED

OUT OF TRAFFIC AND AWAY FROM

FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS

APPLIANCE CORRECTLY WILL VOID

YOUR WARRANTY AND MAY CAUSE A

SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE CARE-

FULLY SUPERVISED WHEN THEY ARE

IN THE SAME AREA AS THE APPLI-

ANCE. TODDLERS, YOUNG CHILDREN

AND OTHERS MAY BE SUSCEPTIBLE

TO ACCIDENTAL CONTACT BURNS. A

PHYSICAL BARRIERS IS RECOMMEND-

ED IF THERE ARE AT RISK INDIVIDUAL

IN THE HOUSE. TO RESTRICT ACCESS

TO A FIREPLACE OR STOVE, INSTALL

AN ADJUSTABLE SAFETY GATE TO

KEEP TODDLERS, YOUNG CHILDREN

AND OTHER AT RISK INDIVIDUALS OUT

OF THE ROOM AND AWAY FROM HOT

SURFACES.

Important Message

SAVE THESE INSTRUCTIONS

City Series Direct Vent Fireplaces must be

installed in accordance with these instructions.

Carefully read all the instructions in this manual

ﬁrst. Consult the "authority having jurisdiction" to

determine the need for a permit prior to starting the

installation. It is the responsibility of the installer to

ensure this ﬁreplace is installed in compliance with

manufacturer's instructions and all applicable codes.

Before You Start

Safe installation and operation of this appliance

requires common sense, however, we are required

by the Canadian Safety Standards and ANSI

Standards to make you aware of the following:

ANY SAFETY SCREEN, GUARD, OR

BARRIER REMOVED FOR SERVICING

THE APPLIANCE, MUST BE REPLACED

PRIOR T O OPERATING THE APPLIANCE.

IF THE BARRIER BECOMES DAMAGED,

THE BARRIER SHALL BE REPLACED

WITH THE MANUFACTURER'S

BARRIER FOR THIS APPLIANCE.

A BARRIER DESIGNED TO REDUCE

THE RISK OF BURNS FROM THE HOT

VIEWING GLASS IS PROVIDED WITH

THIS APPLIANCE AND SHALL BE

INSTALLED FOR THE PROTECTION

OF CHILDREN AND OTHER AT-RISK

INDIVIDUALS

WE RECOMMEND REMOVING THE

GLASS WITH THE GLASS VACUUM

HOLDERS SUPPLIED BY THE MANU-

FACTURER. LOWER THE GLASS TO

REST IN A SAFE PLACE. THIS IS TO

PREVENT DAMAGE TO THE GLASS

EDGES. EXTRA CARE MUST BE TAKEN

WHEN REMOVING/INSTALLING THE

GLASS. BREAKAGE OR DAMAGE TO

THE EDGE OF THE GLASS WHICH

OCCURS AS A RESULT OF CARELESS

HANDLING WILL NOT BE COVERED

UNDER WARRANTY.

City Series CC40EPV | 9

owner's information

General Safety Information

1. The appliance installation must conform with

local codes or, in the absence of local codes,

with the current Canadian or National Gas

Codes, CAN1-B149 or ANSI Z223.1 Installation

Codes.

2. See general construction and assembly

instructions. The appliance and vent should be

enclosed.

3. This appliance must be connected to the

speciﬁed vent and termination cap to the outside

of the building envelope. Never vent to another

room or inside a building. Make sure that the

vent is ﬁtted as per Venting instructions.

4. Inspect the venting system annually for blockage

and any signs of deterioration.

5. Venting terminals shall not be recessed into a

wall or siding.

6. Any safety glass removed for servicing must

be replaced prior to operating the appliance.

7. To prevent injury, do not allow anyone who is

unfamiliar with the operation to use the ﬁreplace.

8. Wear gloves and safety glasses for protection

while doing required maintenance.

9. Be aware of electrical wiring locations in walls

and ceilings when cutting holes for termination.

10. Under no circumstances should this appliance

be modiﬁed. Parts that have to be removed for

servicing should be replaced prior to operating

this appliance.

11. Installation and any repairs to this appliance

should be done by a qualiﬁed service person.

A professional service person should be called

to inspect this appliance annually. Make it a

practice to have all of your gas appliances

checked annually.

12. Do not slam shut or strike the glass door.

13. Under no circumstances should any solid fuels

(wood, paper, cardboard, coal, etc.) be used in

this appliance.

14. The appliance area must be kept clear and

free of combustible materials, (gases and other

ﬂammable vapours and liquids).

10 | City Series CC40EPV

owner's information

* Not offered on all models.

IMPORTANT: The remote control system supplied with this appliance has

several options for starting/operating the appliance using the battery holder

and ON/OFF key on the hand held transmitter.

Prior to operating this appliance, please read the remote control operating

instructions (packaged with remote control) to understand how to operate

this remote control system.

1. Ensure the battery holder switch is in the Remote position and / or wall

mounted battery holder (if equipped) is in the <REMOTE> position.

2. Press and release the ON/OFF button on the remote handheld transmitter

(see Diagram 1). An audible beep should be heard from the receiver. If

not using the remote, the unit can also be turned on by sliding the battery

holder switch to the <ON> position (if equipped).

Note: The ﬁrst try for ignition will last approximately 60 seconds. If there is no

ﬂame ignition (rectiﬁcation) the board will stop sparking for approximately

35 seconds. After wait time , the board will start second try for ignition by

sparking for approximately 60 seconds . If there is still no positive ignition

the board will go into lock out.

The system will need to be reset as follows:

a) Turn the system off by pressing the ON/OFF button on the remote.

b) Wait 5 minutes then repeat from step 2.

Shutdown Procedure

1. Press the ON/OFF button on the remote

2. If service is to be performed, you must disconnect power and shut off gas

to the unit.

ON/OFF

Button

Diagram 1

Remote shown in Manual Mode on Hi

3. After approximately 15 seconds the spark ignition system will spark for 60

seconds to light the main burner.

4. The unit will turn on.

Lighting Procedure

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection

See remote control instructions for details.

*

City Series CC40EPV | 11

owner's information

Copy of the Lighting Plate Instructions

Part #: 919-854

Colours: Black on Grey, except for parts indicated as being Red.

Punch out .25" hole top right corner where indicated.

Size: 100%

w- 6.52"

h- 11.13"

Mar. 12/18: Created decal

Note: Side B of 919-855

w- 6.5"

h- 11"

A) This appliance is equipped with an ignition device which automatically lights the pilot.

Do not try to light the pilot by hand.

B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the oor

because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electric switch, do not use any phone in your building.

- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the re department.

C) Do not use this appliance if any part has been under water. Immediately call a qualied service

technician to inspect the appliance and replace any part of the control system and any

gas control which has been underwater.

A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.

Ne tentez pas d’allumer la veilleuse manuellement.

B) AVANT LA MISE EN MARCHE, reniez tout autour de l’appareil pour déceler une odeur de gaz. Reniez au niveau du plancher, car certains gaz

sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne tentez pas d’allumer l’appareil

• Ne touchez à aucun interrupteur; n'utilisez pas de téléphones se trouvant dans le bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un téléphone extérieur. Suivez les instructions du fournisseur.

• Si vous ne pouvez pas rejoindre le fournisseur, appelez le service incendie.

C) N’utilisez pas cet appareil s’il a été plongé dans l’eau, même partiellement. Faites inspecter l’appareil par un technicien qualié et remplacez

tout élément du système de contrôle ou de commande qui a été plongé dans l’eau.

DO NOT REMOVE THIS INSTRUCTION PLATE

NE PAS ENLEVER CETTE ÉTIQUETTE D’INSTRUCTIONS

TO TURN OFF GAS APPLIANCE / POUR ÉTEINDRE UN APPAREIL AU GAZ

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54,

or Natural Gas and Propane Installation Codes, CSA B149.1.

Cet appareil doit être installé conformément aux codes locaux, s’il y a lieu. En l’absence de tels codes, suivre le National Fuel Gas Code,

ANSI Z223.1/NFPA 54, ou les Natural Gas and Propane Installation Codes, CSA B149.1.

CAUTION: Hot while in operation. Do not touch. Severe burns may result. Due to high surface temperatures keep

children, clothing and furniture, gasoline and other liquids having ammable vapors away. Keep burner and control

compartment clean. See installation and operating instructions accompanying appliance.

ATTENTION : Surfaces chaudes lorsque l’appareil est en marche. Ne pas toucher. Risque de brûlures graves. En raison

des températures élevées, les enfants, les vêtements et le mobilier, le carburant et tout autre liquide aux vapeurs

inammables doivent être tenus éloignés de l’appareil. Nettoyer régulièrement le brûleur et le compartiment des

commandes. Voir les consignes d’installation et d’utilisation fournies avec l’appareil.

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,

personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or

property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional

information consult a qualified installer, service agency or gas supplier.

AVERTISSEMENT : Quiconque ne respecte pas scrupuleusement les instructions de la présente notice risque de déclencher

un incendie ou une explosion pouvant entraîner des dégâts matériels ou des blessures pouvant être mortelles.

Tout défaut d'installation, de réglage, de modication, de service ou d'entretien peut entraîner des blessures ou des dom-

mages matériels. Reportez-vous au manuel d'utilisation fourni avec cet équipement. Pour obtenir de l'aide ou des informa-

tions complémentaires, consulter un installateur ou un service d'entretien qualié, ou le fournisseur de gaz.

1) Ensure the Main switch is in the ON position and/or the wall mounted battery holder (if equipped) is in the <REMOTE> position.

2) Press and release the ON/OFF button on the remote handheld transmitter. An audible beep should be heard from the receiver. If not

using the remote, the unit can also be turned on by sliding the battery holder switch to the <ON> position (if equipped).

3) After approximately 15 seconds the spark ignition system will spark for 60 seconds to light the main burner.

4) The unit will turn on.

Note: The rst attempt to ignition will last approximately 60 seconds. If there is no ame ignition (rectication) the board will stop spark-

ing for approximately 35 seconds. After this wait time, the board will start a second try for ignition by sparking for approximately 60

seconds. If there is still no positive ignition after the second attempt the board will go into lock out.

The system will need to be reset as follows (after going into lock out mode):

a) Wait 5 minutes - turn the system o by pressing the ON/OFF button on the remote.

b) After approximately 2 seconds press the ON/OFF button again.

c) Unit will repeat step 2.

1) S’assurer que le commutateur principal est en position ON et/ou que le bloc-piles mural (le cas échéant) est en position <REMOTE>.

2) Appuyer sur la touche ON/OFF de la télécommande puis relâcher. Un bip sonore retentira depuis le récepteur. Si vous n'utilisez pas

la télécommande, l'appareil peut également être allumé en faisant glisser le commutateur du bloc-piles sur la position <ON> (le cas

échéant).

3) Après environ 15 secondes, le système d'allumage produira une étincelle pendant 60 secondes pour allumer le brûleur principal.

4) L'appareil s’allumera.

Remarque : Au premier allumage, le système tente d’allumer les ammes pendant 60 secondes. Si l’essai est infructueux, le système

fera une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectication. Ce délai écoulé, le système tente à nouveau d'allumer les

ammes en produisant des étincelles pendant 60 secondes. Si les ammes ne s’allument toujours pas, le système se met en mode ver-

rouillage.

Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) :

a) Attendre 5 minutes et éteindre l’appareil en appuyant sur la touche ON/OFF de la télécommande.

b) Attendre 2 secondes et appuyer encore une fois sur la touche ON/OFF.

c) L'appareil répètera l'étape 2.

1) Press the ON/OFF button on the remote.

2) If service is to be performed–you must disconnect power and shut off gas to the unit.

1)

Appuyer sur la touche ON/OFF de la télécommande.

2) Lors de l'entretien de l'appareil, vous devez débrancher l'alimentation électrique et couper le gaz alimentant l'appareil.

LIGHTING INSTRUCTIONS / CONSIGNES D’ALLUMAGE

FOR YOUR SAFETY READ BEFORE LIGHTING

POUR VOTRE SÉCURITÉ – À LIRE AVANT LA MISE EN MARCHE

12 | City Series CC40EPV

owner's information

Proﬂame II Remote Control Operating Instructions

919-829

09.29.17

PROFLAME II REMOTE CONTROL OPERATING INSTRUCTIONS

WARNING: THE TRANSMITTER AND RECEIVER ARE RA‑

DIO FREQUENCY DEVICES. PLACING THE RECEIVER IN

OR NEAR METAL MAY SERVERELY REDUCE THE SIGNAL

The Proﬂame 2 Transmitter provides for controlling the following hearth

appliance functions:

1. Main Burner On/Off

2. Main Burner ﬂame modulation (6 levels)

3. Choice of standing or intermittent pilot (CPI/IPI)

4. Thermostat and Smart thermostat functions

5. Accent light modulation (6 levels)**

6. Split ﬂow valve**

7. Comfort Fan speed modulation (6 levels)**

** This feature is not available on all models.

IMPORTANT:The Proﬂame Transmitter 2 is an integrated part of the

Proﬂame 2 System, which consists of these elements:

• Proﬂame 2 Transmitter, to be used in conjunction with:

• Integrated Fireplaces Control (Proﬂame 2 IFC)

The Proﬂame Transmitter uses a streamline design with a simple button

layout and informative LCD display (Fig. 1). A Mode Key is provided to

index between the features and a Thermostat Key is used to turn on/off

or index through Thermostat functions (Fig. 1 & 2). Additionally, a Key

Lock feature is provided (Fig. 22).

Figure 1: Proﬂame Transmitter

Figure 2: Transmitter LCD Display

TECHNICAL DATA

REMOTE CONTROL

Supply Voltage 4.5V (three 1.5V AAA batteries)

Ambient temperature

ratings

0 - 50

o

C (32 - 122

o

F)

Radio Frequency 315 MHZ

ATTENTION!

- Turn “OFF” the main gas supply of the appliance during installation or

maintenance of the Receiver device.

- Turn “OFF” main gas supply to the appliance prior to removing or rein-

serting the batteries.

- In case of remote control malfunction, turn off the IFC device using the

"ON/OFF" main switch.

- For installation / maintenance, switch off the IFC device removing main

power supply plug.

OPERATING PROCEDURE

Initializing the System for the ﬁrst time

Power the receiver. Activate the procedure of the receiver address pro-

gramming, see the receiver instruction (*). The Receiver will “beep” three

(3) times to indicate that it is ready to synchronize with a Transmitter. Install

the 3 AAA type batteries in the Transmitter battery bay, located on the

base of the Transmitter. (ﬁg. 3) With the batteries already installed in the

Transmitter, push the On button. The Receiver will “beep” four times to

indicate the Transmitter’s command is accepted and sets to the particular

code of that Transmitter. The system is now initialized.

(*) The receiver may be independent or integral to the IFC hearth ap-

pliance control module. The receiver instruction may not be indepen-

dent when part of the IFC.

Figure 3: Battery Compartment

4

PROFLAM

E 2

TRANSMI

TTER

USE

ANDINST

AL

L

The Proflame Remote Control System consists of three elements:

1. Proflame Transmitter.

2. Proflame Receiver and a wiring harness to connect the Receiver to the gas valve, stepper

motor and Fan Control Module.

3. Proflame Fan Control Module (FCM)

The Proflame Transmitter uses a streamline design with a simple button layout and informative

LCD display (Fig. 1).

The Transmitter is powered by 3 AAA type batteries.

A Mode Key is provided to Index between the features and a Thermostat Key is used to turn on/

off or index through Thermostat functions (Fig. 1 & 2).

TRANSMITTER (Remote Control with LCD Display)

SYSTEM DESCRIPTION

Fig. 1: PROFLAME Transmitter.

Low battery alarm

Child safety lock-out

Room

Temperature

Aux ON

Set Point

Temperature/Level/State

Flame ON

Thermostat OFF/

ON/SMART

Fan

Fig. 2: Transmitter LCD display.

Transmission

Turn on the Appliance

With the system OFF, press the ON/OFF Key on the

Transmitter. The Transmitter display will show some other

active Icons on the screen. At the same time the Receiver

wil activate the appliance. A single “beep” from the

Receiver will confirm reception of the command.

Turn off the Appliance

With the system ON, press the ON/OFF Key on the

Transmitter. The Transmitter LCD display will only show

the room temperature (Fig. 6). At the same time the

Receiver will turn off the appliance. A single “beep” from

the Receiver confirms reception of the command.

Fig. 6: Remote Control display.

3 Positions Slider

Fig. 4: Proflame Receiver body.

PRG Key

Fig3: Battery

compartment.

Fig. 4: Remote Control display in Farenheit. Fig. 5: Remote Control display in Celsius.

9957099_00_nero_mod_05-10-2011.i4 4 05/10/2011 8.36.38

1

City Series CC40EPV | 13

owner's information

919-829 09.29.17

Figure 4: Remote Control dis-

play in Farenheit.

Temperature indication Display

With the system in the "OFF" position, press the Thermostat Key and

the Mode Key at the same time. Look at the LCD screen on the transmit-

ter to verify that a C or F is visible to the right of the room temperature

display (Figures 4 & 5).

Figure 5: Remote Control dis-

play in Celsius.

Turn on the Appliance

With the system OFF, press the ON/

OFF Key on the Transmitter. The

Transmitter display will show some

other active Icons on the screen. At

the same time the Receiver wil ac-

tivate the appliance. A single “beep”

from the Receiver will conﬁ rm recep-

tion of the command.

Figure 6: Remote Control

display

Remote-Flame Control

The proﬂ ame has six (6) ﬂ ame levels. With the system on, and the ﬂ ame

level at the maximum in the appliance, pressing the Down Arrow Key

once will reduce the ﬂ ame height by one step until the ﬂ ame is turned off.

The Up Arrow Key will increase the ﬂ ame height each time it is pressed.

If the Up Arrow Key is pressed while the system is on but the ﬂ ame is off,

the ﬂ ame will come on in the high position. ( Fig. 7 & 8 ) A single “beep”

will conﬁ rm reception of the command.

Fig. 7

Fig. 8

Room Thermostat (Transmitter Operation)

The Remote Control can operate as a room thermostat. The thermostat

can be set to a desired temperature to control the comfort level in a room.

To activate this function, press the Thermostat Key (Fig. 1). The Lcd

display on the Transmitter will change to show that the room thermostat

is “ON” and the set temperature is now displayed (Fig. 9). To adjust the

set temperature, press the Up or Down Arrow Keys until the desired set

temperature is displayed on the LCD screen of the Tr ansmitter.

Figure 9 Figure 10

Turn off the Appliance

With the system ON, press the ON/OFF Key on the Tr ansmitter. The

Transmitter LCD display will only show the room temperature (Fig. 6).

At the same time the Receiver will turn off the appliance. A single “beep”

from the Receiver conﬁ rms reception of the command.

2

14 | City Series CC40EPV

owner's information

919-829

09.29.17

Smart Thermostat (Transmitter Operation)

The Smart Thermostat function adjusts the ﬂ ame height in accordance

to the difference

between the set point temperature and the actual room temperatures.

As the room

temperature gets closer to the set point the Smart Function will modulate

the ﬂ ame down.

To activate this function, press the Thermostat Key (Fig. 1) until the word

"SMART" appears to

the right of the temperature bulb graphic (Fig. 11).

To adjust the set temperature, press the Up or Down Arrow Keys until

the desidered set

temperature is displayed on the LCD screen of the Tr ansmitter (Fig. 12).

Note. When Smart Thermostat is activated, manual ﬂ ame height adjust-

ment is disabled.

Figure 12Figure 11: Smart Flame Function

Fan Speed Control**

If the appliance is equipped with a hot air circulating fan, the speed of

the fan can be controlled by the Proﬂ ame system. The fan speed can be

adjusted through six (6) speeds. To activate this function use the Mode Key

(ﬁ g.1) to index to the fan control icon (Fig. 13). Use the Up/Down Arrow

Keys (ﬁ g.1) to turn on, off or adjust the fan speed (ﬁ g. 14). A single “beep”

will conﬁ rm reception of the command.

Figure 13 Figure 14

Remote dimmer control (Light)**

The auxiliary function controls the AUX power outlet by the dimmable

light control. To activate this function use the Mode Key (ﬁ g. 1) to index

to the AUX icon (ﬁ g. 15 & 16).

The intensity of the output can be adjusted through six (6) levels. Use

the Up/Down Arrow Keys (ﬁ g.1) adjust the output level (ﬁ g. 16). A single

“beep” will conﬁ rm reception of the command.

Note: This function is available only with the IFC Control Module.

Figure 15 Figure 16

Split Flow control**

The secondary burner is controlled by the split Flow. To activate this

function use the Mode Key (ﬁ g. 1) to index to the SPLIT FLOW mode

icon (ﬁ g. 17 & 18).

Pressing the Up Arrow Key will activate the secondary burner. Pressing

the Down Arrow Key will turn the secondary burner off. A single “beep”

will conﬁ rm the reception of the command.

Figure 17 Figure 18

3

City Series CC40EPV | 15

owner's information

919-829 09.29.17

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection

Note: Power vent models do not have a Continuous

Pilot option.

With the system in "OFF" position press the Mode Key (ﬁ g. 1) to index

to the CPI mode icon (ﬁ g. 19 & 20).

Pressing the Up Arrow Key will activate the Continuous Pilot Ignition

mode (CPI). Pressing the Down Arrow Key will return to IPI. A single

“beep” will conﬁ rm the reception of the command.

Figure 19 Figure 20

KEY LOCK

This function will lock the keys to avoid unsupervised operation.

To activate this function, press the MODE and UP Keys at the same

time (ﬁ g. 21).

To de-activate this function, press the MODE and UP Keys at the

same time.

Figure 21

LOW BATTERY POWER DETECTION

Transmitter

The life span of the remote control batteries depends on various factors:

quality of the batteries used, the number of ignitions of the appliance,

the number of changes to the room thermostat set point, etc.

When the Transmitter batteries are low, a Battery Icon will appear on the

LCD display of the Tr ansmitter (Fig. 22) before all battery power is lost.

When the batteries are replaced this Icon will disappear.

Figure 22

CPI/IPI SWITCH

This appliances comes equipped with a CPI/IPI switch. The function of

both the CPI/IPI switch are as follows:

Continuous pilot (CPI) - A pilot that when in operation, is intended to

remain continuously ignited until it is manually interrupted.

Intermittent pilot (IPI) - A pilot that is automatically ignited when an ap-

pliance is called on to operate and which remains continuously ignited

during each period of main burner operation. The pilot is automatically

extinguished when each main burner operating cycle is completed. The

mode of the ﬁ replace is easily changed from an intermittent pilot ignition

system (IPI) to a continuous pilot ignition system (CPI) by using remote

control as noted above.

The beneﬁ ts of having as CPI are as follows:

- Keeps venting primed for trouble free start-up under colder weather

conditions or inversions.

- Keeps the unit glass warm, which decreases the amount of condensa-

tion on start-up

-Provides owners with ﬂ exibility to choose a traditional continuous pilot.

The primary beneﬁ t of having the IPI function is a signiﬁ cant savings on

fuel as the pilot will only run when there is a call for heat.

Thermostat Icon: If the thermostat icon is not present on the remote

transmitter, follow instructions noted below

1. Ta ke one or all batteries out (removing one battery will work).

2. Press and hold down the Thermostat button on the remote.

3. Reinstall the 3rd battery while still holding thermostat button down.

4. If you see "Set" the thermostat option is now enabled. If you see "Clr"

the thermostat option is now disabled

5. Repeat the procedure if you did not see the "Set" or "Clr" to remove

or add the option back to the remote.

Enable all other functions if not present on the remote transmitter, follow

instructions noted below:

1. Remove one battery or all batteries (removing one battery will work).

2. Press and hold both the ON/OFF and the MODE button at the same time .

3. Reinstall the 3rd battery while still holding both buttons (keep holding

buttons once 3rd battery is installed, then release the mode button only.

4. The screen will show either "Clr" or "Set" with the 1st mode being

your option to disable or enable.

5. "Clr" will remove the mode by using the up or down arrow while still

holding both buttons (icon will disappear once removed, or icon

will

show up again once added).

6. Use the "Mode" button to move to the next function.

7. "Set" will add that mode by using the up or down arrow while still

holding both buttons (icon will disappear once removed, or icon

will show up again once added) Use the "Mode" button to move

to the next function.

Note: You should never program out the fan (if installed) or CPI/IPI

mode on the remote.

4

Important: If set to CPI mode, the pilot will continue to run at all times

but this will also cause the power vent blower to remain on at all times

as a result of the pilot being on. Keep this set to IPI mode only. Never

use CPI as it is not required when operating a power vented appliance.

16 | City Series CC40EPV

owner's information

Inner Glass Panel (Firebox Glass) Installation / Removal

1. Remove outer safety glass panels if previously installed–see instructions

in this manual.

2. CC40LE/CC40RE Single sided & CC40LE/CC40RE 3 Sided Units—Re-

move outer panels installed in units - see panel removal section in this manual.

Single sided units–proceed to Step 5.

3. Ensure all 4 clamps on each side are open to allow clearance for the glass.

Lift up side panel using supplied vacuum clamp and tilt inward and upward

positioning into a top channel and lowering gently into the lower glass chan-

nel–slide the side glass panel ﬁrmly towards the back wall until the springs

at the back wall are compressed.

4. With the springs compressed, close the 2 clamps at the bottom and 2 clamps

at the top, by turning inward, to secure the glass in position. For the 3 sided

unit, repeat on the opposite side.

Top clamps in

open position

Bottom side clamps in

open position

CC40LE/CC40RE shown

Bottom

channel

Top clamps in

closed position

Bottom clamps in

closed position

Push side glass

panel ﬁrmly

to back wall

until springs are

compressed—

then close

clamps.

Important:

Prior to installing the inner glass, ensure that there is no media present in

the bottom channel as this can cause damage to the glass. Remove any

media from bottom channel prior to installing the glass.

WARNING: GLASS HANDLING

We recommend using the glass vacuum holders supplied by the manufac-

turer. Lower the glass to rest in a safe place, this is to prevent damage to the

glass edges. Extra care must be taken when removing/installing the glass.

Breakage or damage to the edge of the glass which occurs as a result of

careless handling will not be covered under warranty.

• We recommend handling the glass with supplied vacuum

clamps

• When removing glass–prepare a soft, scratch resistant

surface to place the glass

• Never clean or remove hot glass

Note: The suction cups may leave a round ﬁlm on the glass

when used. Ensure that the glass is cleaned using a ﬁreplace

glass cleaner prior to operating the appliance.

Note: glass panels must be installed to operate ﬁreplace

To watch the ﬁrebox installation video click here http://bit.ly/2qfQwST

City Series CC40EPV | 17

owner's information

Note: Ensure that the front glass is centered and evenly spaced with side glass

(3 sided unit) - open to release glass clamps to remove from surface of glass.

CC40LE shown

Handle front panel with supplied vacuum clamps

tooltip

Open clamps

prior to placing

front glass

panel

5. Ensure all 7 front clamps are in the open position to allow clearance for

the glass.

6. Lift up the front panel using the supplied vacuum clamps and position into

the lower front channel–ensure the front panel is accurately centered—with

the front panel in position—secure in place by closing the 3 lower clamps

and 4 upper clamps.

Open clamps to

release pressure on

the springs

Press glass vacuum clamps in open position ﬁrmly onto surface of glass. Bring

handles together to close.

Open

Closed

7. Return to the side panel(s), and release the upper and lower clamps. The

springs will release and push the glass side panel forward slightly—this will

create a seal between the front and side panels. When the junction between

the front and side glass panels is sealed, close the clamps to secure the

side panel(s) in place.

8. To remove the glass panels—always remove the side panel(s) (for 3 sided

units) before removing the front panel.

9. Reverse steps to remove glass.

18 | City Series CC40EPV

owner's information

To watch the safety barrier glass installation video click here http://bit.ly/2ryq0c0

Outer Safety Glass Panel (Barrier Glass) Installation / Removal

Outer glass safety panels to be installed during the initial installation after the

unit is in the ﬁnal position.

Note: The outer safety panels come with plastic corners to protect these against

damage. These should be kept in place until such time the outer safety panels

are installed. Ensure these are removed prior to operating the appliance. Keep

the plastic corners in a safe place if ever removing the outer panels for servicing.

1. Carefully remove glass safety panels from packaging.

3. Tilt the top of the glass panel inward and lift up and underneath

the upper front panel of the outside frame. Hook the glass panel

onto the pins and also onto the two angle adjustment brackets lo-

cated on the frame in two locations as shown in the diagram below.

Note: The front frame upper panel is shown as transparent to better

illustrate the install (this area is not visible when installing glass).

Press glass vacuum clamp in open position ﬁrmly onto surface of glass. Bring

handles together to close.

Open

Closed

NOTE: Inner glass panel shown in image - depicting proper handling

of glass.

WARNING: GLASS HANDLING

We recommend using the glass vacuum holders supplied by the manufac-

turer. Lower the glass to rest in a safe place, this is to prevent damage to the

glass edges. Extra care must be taken when removing/installing the glass.

Breakage or damage to the edge of the glass which occurs as a result of

careless handling will not be covered under warranty.

• We recommend handling the glass with supplied vacuum

clamps

• When removing glass–prepare a soft, scratch resistant

surface to place the glass

• Never clean or remove hot glass

Note: The suction cups may leave a round ﬁlm on the glass

when used. Ensure that the glass is cleaned using a ﬁreplace

glass cleaner prior to operating the appliance.

Note: If the outer safety glass panels do not sit at 90º and angle too far

inward or outward, remove the glass panel and adjust the screw of

the panel angle bracket. Turn the panel angle bracket screw in 1/4

increments—reinstall panel to check.

Angle adjustment brackets

Pins on body of unit

Panel angle bracket—to

adjust, turn screw:

Clockwise = bring panel in

Counter clockwise= bring

panel out

2. Using the supplied vacuum clamps, lift the large front glass panel and

position it front and centre by manoeuvering up and underneath the front

of the unit frame.

Note: safety glass panels must be installed to operate ﬁreplace

City Series CC40EPV | 19

owner's information

Outer Safety Glass Panel (Barrier Glass) Installation / Removal

Note: safety glass panels must be installed to operate ﬁreplace.

Note: If the outer safety glass side panels angle too far inward or outward,

remove the side glass panel and adjust on the panel angle bracket,

see details on previous page.

5. Lift up the side panel with the supplied glass clamps (see procedure on

previous page). Tilt the side of the glass panel inward and lift up and under-

neath the upper side panel and hook the 2 outer hooks on to the pins, there

is also a panel angle adjustment bracket for the third hook.

Note: The side frame upper panel is shown as transparent to better

illustrate the install (this area is not visible when installing glass).

4. For 3 sided and corner units only:

With front panel installed, proceed to install the side panel(s).

Identify the left and right side panels before installing. Facing the front of

the unit, the right panel will show an arrow pointing to the front of the unit

as shown in the diagram below.

Note: After the side panel has been adjusted so it is installed at 90º to the

unit and not ﬂaring in or out, check to ensure there is no gap between

the front and side panel. If there is a gap as shown below, slide the side

panel to adjust the position and close the gap.

Direction arrow on side

panel bracket, should

point toward front of

unit

6. Repeat Steps 4 and 5 to install the opposite side panel.

7. Reverse Steps to remove all panels.

Note: When removing panels, we recommend using the supplied glass clamps.

Panel

angle bracket

20 | City Series CC40EPV

owner's information

and exterior portions of the system being

exposed to cold weather.

4. Inspect joints, to verify that no pipe sections or

ﬁttings have been disturbed, and consequently

loosened. Also check mechanical supports

such as Wall Straps, or plumbers' tape for

rigidity.

Log Replacement

The unit should never be used with broken logs.

Turn off the gas valve and allow the unit to cool

before opening door and carefully remove the logs.

(The pilot light generates enough heat to burn

someone.) If for any reason a log should need

replacement, you must use the proper replacement

log. The position of these logs must be as shown

in the diagrams under Log Installation.

Note: Improper positioning of logs may

create carbon build-up and will

severely alter the unit's performance

which is not covered under warranty.

Glass Gasket

If the glass gasket requires replacement use a

tadpole glass gasket (Part # 936-220).

Glass

Your Regency

®

ﬁreplace is supplied with high

temperature 5mm-Tempered outer glass & 5mm-

Ceramic inner glass. If your glass requires cleaning,

we recommend using an approved glass cleaner

available at all authorized dealers. Do not use

abrasive materials.

CAUTION & WARNINGS:

* Do not clean when the glass is hot.

* The use of substitute glass will void all

product warranties.

* Care must be taken to avoid breakage of

the glass.

* Do not strike or abuse the glass.

* Do not operate this ﬁreplace without the

glass front or with a cracked or broken

glass front.

* Wear gloves when removing damaged or

broken glass.

* Replacement of the glass panels should be

done by a licensed or qualiﬁed service person.

Glass Replacement

In the event that you break your glass by impact,

purchase your replacement from an authorized

Regency dealer only. Replacement glass is shipped

already installed into the door frame. Reinstall as per

Glass Installation in the "Glass Installation" section.

REPLACEMENT GLASS:

CC40LE/CC40RE

Inner Glass Front - Ceramic (Part# 940-436/P)

Inner Glass Side - Ceramic (Part# 940-437/P)

CC40LE

Outer Safety Glass Side - Tempered Large

#940-486/P

Outer Safety Glass Side - Tempered Small

# 940-440/P

CC40RE

Outer Safety Glass Side - Tempered Large

#940-485/P

Outer Safety Glass Side - Tempered Small

#940-439/P

Maintenance Instructions

1. Always turn off the gas valve before cleaning.

For relighting, refer to lighting instructions. Keep

the burner and control compartment clean by

brushing and vacuuming at least once a year.

When cleaning the logs, use a soft clean paint

brush as the logs are fragile and easily damaged.

2. Clean appliance and door with a damp cloth

(never when unit is hot). Never use an abrasive

cleaner. The glass should be cleaned with a gas

ﬁreplace glass cleaner. The glass should be

cleaned when it starts looking cloudy.

3. The ﬁreplace is ﬁnished in a heat resistant paint

and should only be reﬁnished with heat resistant

paint. Regency

®

uses StoveBright Paint - Metallic

Black #6309.

4. Make a periodic check of burner for proper

position and condition. Visually check the ﬂame

of the burner periodically, making sure the ﬂames

are steady; not lifting or ﬂoating. If there is a

problem, call a qualiﬁed service person.

5. The appliance and venting system must be

inspected before use, and at least annually, by

a qualiﬁed ﬁeld service person, to ensure that

the ﬂow of combustion and ventilation air is not

obstructed.

Note: Never operate the appliance without

the glass properly secured in place.

6. Do not use this appliance if any part has been

under water. Immediately call a qualiﬁed service

technician to inspect the appliance and to

replace nay part of the control system and any

gas control which has been under water.

7. In the event this appliance has been serviced

check that the vent-air system has been properly

resealed & reinstalled in accordance with the

manufacturer's instructions.

8. Verify operation after servicing.

General Vent Maintenance

Conduct an inspection of the venting system semi-

annually. Recommended areas to inspect as follows:

1. Check the Venting System for corrosion in areas

that are exposed to the elements. These will

appear as rust spots or streaks, and in extreme

cases, holes. These components should be

replaced immediately.

2. Remove the Cap, and shine a ﬂashlight down

the Vent. Remove any bird nests, or other foreign

material.

3. Check for evidences of excessive condensation,

such as water droplets forming in the inner

liner, and subsequently dripping out the joints,

Continuous condensation can cause corrosion

of caps, pipe, and ﬁttings. It may be caused by

having excessive lateral runs, too many elbows,

Page is loading ...

Regency Fireplace Products CitySeries Chicago Corner 40RE Power Vent Owner's manual

This manual is also suitable for

Regency Fireplace Products CitySeries Chicago Corner 40RE Power Vent Owner's manual

Related papers

Other documents